

Edge Atmos PCB
A local weather station built with no HAL and all custom drivers and libraries built from bare-metal register level coding.
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 7
- Nets
- 51
- Pads
- 74
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 10 Mar 2026
- Updated
- 2 Nov 2026
Overview
Edge Atmos PCB is an open-source printed circuit board by ShreyasKombinadka, from the ShreyasKombinadka/Edge-Atmos repository on GitHub. It is a 2-layer board with 7 parts on 51 nets.
It is built around the AHT10 and BMP280. It belongs with the home automation and IoT boards and the STM32 boards of this library.
Main components
2AHT10
SMD-40℃~+85℃ 0%RH~100%RH 1.8V~3.6V 23uA Factory calibration I2C ±0.3℃ ±2%RH SMD Temperature and Humidity Sensor ROHSAosong ElecTemperature And Humidity SensorBMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure Sensors
README
README.mdEdge Atmos
A local weather station built with no HAL and all custom drivers and libraries built from bare-metal register level coding.
Overview
- Built on STM32 board with no HAL.
- All the driver and libraries are custom built.
Status
- Firmware
- Hardware
- Completed
Libraries built
- I2C driver
- LCD1602 driver
- ASCII conversion library
- AHT10 Temperature and humidity sensor driver
- BMP280 Pressure sensor driver
- GPIO driver
- SPI driver
- W25Q32 Flash memory driver
- ST7789LCD TFT display driver
- Font bitmap file
Parts
7| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | AHT10 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | BMP280 | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J2 |
| 1 | Conn_01x04 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J7 |
| 1 | STM32F103C8T6_1 | Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_Vertical | J4 |
| 1 | STM32F103C8T6_2 | Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_Vertical | J5 |
| 1 | TFT | Connector_PinSocket_2.54mm:PinSocket_1x14_P2.54mm_Vertical | J6 |
| 1 | W25Q32 | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J3 |
Similar boards
- 2 layers38.3 × 20.8 mm

- 2 layers35.3 × 18.4 mm

Remote Temp Humidity Sensor
gadjet/Multifunction-ESP8266-Sensor-board
AKA Wireless window/door sensor version 4
28 parts3GPL-3.0 - 2 layers38.4 × 27.4 mm

- 4 layers50 × 50 mm

Dryer control
souptik-samanta/dryer
A custom PCB and self-centering spool holder for drying 3D printer filament. The PCB controls the fans, monitors temperature, and provides connections for PTC heaters.
33 parts1 - 2 layers120 × 80 mm

- 2 layers96.1 × 70 mm

Adapter
ErBWs/GD32-Mesh
LoRa & 4G Mesh with GD32, my bachelor's thesis. 基于 GD32 的 LoRa 组网和 4G 通信,本科毕业设计
5 partsGPL-3.0 - 2 layers60.1 × 42.3 mm

TermoHumi
LinJesUxUs/TermoHumi
Thermo-hygrometer code, powered on ATMega, AHT10 sensor and 7 Segment Display.
91 parts - 2 layers26.9 × 46.7 mm

Questions
What parts does the Edge Atmos PCB use?
7 parts, built around the AHT10 and BMP280. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Edge Atmos PCB KiCad files?
From the ShreyasKombinadka/Edge-Atmos repository on GitHub, at the commit this page was made from: the board is PCB/Edge_Atmos_PCB.kicad_pcb and its schematic PCB/Edge_Atmos_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Edge Atmos PCB design in my own project?
Its repository states no licence, so its author keeps all rights: ask ShreyasKombinadka before reusing the design.