Skip to the content
4 layers60.4 × 110 mmSpankulator, the printed circuit board in 3D

The Spankulator is a WiFi-enabled multi-function Eurorack module. Its main function is to generate a trio of coordinated analog and digital signals which can be used in an endless variety of ways.

Size
60.4 × 110 mm
Copper layers
4
Thickness
1.6 mm
Parts
107
Nets
81
Pads
335
Tracks, vias
656, 98
Pours
4
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
5 Sep 2022
Updated
21 Feb 2025

Overview

Spankulator is an open-source printed circuit board by shannon-greenlight, from the shannon-greenlight/spankulator repository on GitHub. It is a 4-layer board of 60.4 × 110 mm with 107 parts on 81 nets, routed with 656 tracks and 98 vias.

It is built around the TL072CP, MCP6002-E/P and CD4013BE, with the MAX7480EPA among its other parts. Its parts include 30 resistors, 21 capacitors, 15 diodes, 10 connectors and 8 ICs.

Main components

4

README

README.md

Spankulator

The Spankulator has been discontinued due to parts issues

The Spankulator is a WiFi-enabled multi-function Eurorack module. Its main function is to generate a trio of coordinated analog and digital signals which can be used in an endless variety of ways. While each output generates familiar signals, it is the coordination of these signals and the methods of control that make the Spankulator special.

Spankulator-Hardware, Spankulator-Panel

These repos contain the materials needed to construct the Spankulator main board and the front panel. The files are for KiCAD 6.0. Go to the Greenlight Kicad repo to get the needed libraries. The gerber files work with JLCPC and will most likely work with other board manufacturers. Assembly instructions are in spankulator_assembly.docx.

If starting from a bare circuit board, the BOM for the Spankulator is in bom/Digi-Key/spankulator_full.csv. This file can be directly uploaded to Digi-Key for buying parts.

If using the JLCPCB assembly service, the BOM is split into 3 parts.

  • bom/LCSC/spankulator_bom.csv : The parts to be assembled by JLCPCB
  • bom/Digi-Key/spankulator_split.csv : The remaining parts to be assembled by user
  • bom/Other/other_bom.xlsx : The parts that must be bought from sources other than JLCPCB and Digi-Key

Also, when an assembly service is used, a component position file is required. This file's path is: fab/spankulator_cpl.xlsx

notes: The bom and cpl files are auto-generated from the csv BOM files produced by KiCAD. You will need to refresh the data when changes to the schematic that affect the BOM or changes to the board layout occur. The data that is the source of the BOM files is generated by the BOM function in KiCAD schematics. Use the bom2grouped_csv.xsl plugin that's supplied with KiCAD. This produces Spankulator.xml, which is used by the Python scripts found in the KiCAD repository. https://github.com/shannon-greenlight/KiCAD Once Spankulator.xml is up to date, use the generate_boms.bat batch file to create the BOMs. Edit this file to set the directory locations to match your system. The cpl file source is generated by the KiCAD pcb Fabrication Output function. File->Fabrication Outputs->Component Placement. Make sure to select "Separate files for front and back". Select ./fab/pos as the output directory. This creates the pos files, the 'top' file being used as the data source for the cpl file that is sent to JLCPCB: fab/spankulator_cpl.xsl Make sure to refresh the data and save the file before sending it to JLCPCB.

The additional data fields that appear on the schematic help to produce the different BOM files. They must be maintained for these BOMs to come out right.

Spankulator-Code

This repository contains the elements needed to build code for the Spankulator. The code is for the Arduino Nano 33 IoT and is found in the Spankulator folder. Make sure to get the required libraries from the Arduino-Libs repo.

The build files are for Windows. They are simple .bat files but depend on having a working Arduino development system. Certain variables must be edited to adapt these files to a particular installation.

Here is a list of the batch files and folders:

  • make.bat ... compiles the code
  • make_n_load.bat ... calls make.bat then uploads the code to the Spankulator
  • load_recent.bat ... loads most recent compile
  • list_ports.bat ... lists available COM ports
  • release.bat ... used to update release number in the code and create release binary zip
  • out ... this folder must be created. It holds compile output

Du Dad

The Du Dad is an addition to the Spankulator that provides these benefits:

  • Front Panel USB access
  • Power sensing shuts off USB to Arduino when synth power is off
  • Reset switch
  • USB Power indicator
  • Boot Loader / Ext Trig Disabled indicator
  • Trig In Latch indicator
  • Extremely useful to those who use Terminal Remote mode

The folder structure of the Du Dad is similar to the Spankulator Hardware folder. Currently there is no support for assembly service.

Parts

107
QtyValueFootprintReferences
8100nFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC5, C6, C7, C9, C12, C13, C17, C20
810KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R5, R6, R11, R15, R16, R21, R22
71N5711Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D2, D7, D15, D16, D19, D20
7Push ButtonButton_Switch_THT:SW_PUSH_6mmSW2, SW3, SW4, SW5, SW6, SW7, SW8
6100K .1%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR7, R12, R24, R26, R27, R31
51KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R3, R4, R10, R14
53.5mm Jacksputterizer:Molex-0472570001J1, J3, J4, J5, J6
410nFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC1, C2, C18, C19
41uFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC8, C10, C14, C21
4MountingHoleMountingHole:MountingHole_2.5mmH1, H2, H3, H4
4TestPointTestPoint:TestPoint_Keystone_5005-5009_CompactTP1, TP2, TP3, TP4
2100uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC3, C4
21N4148Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD6, D13
22.2uFsputterizer:CP_Radial_Tantal_D4.5mm_P5.00mm_MinC11, C15
220KPotentiometer_THT:Potentiometer_Bourns_3266Y_VerticalRV2, RV3
22x5 HeaderConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_VerticalJ2, J7
2300K .1%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR23, R28
243KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR9, R13
2470Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR19, R20
2Arduino Socketsputterizer:ArduinoConnectorJ12, J13
2MountingHolesputterizer:MountingHole_2.5mm-No-MarginH6, H7
2TL072CPPackage_DIP:DIP-8_W7.62mm_SocketU1, U3
1100KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR8
11KPotentiometer_THT:Potentiometer_Bourns_PTV09A-1_Single_VerticalRV1
11N5819Diode_THT:D_DO-41_SOD81_P2.54mm_Vertical_KathodeUpD9
11N5819Diode_THT:D_DO-41_SOD81_P2.54mm_Vertical_AnodeUpD8
1200K .1%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR29
1270pCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC16
12N3904digikey-footprints:TO-92-3_Formed_LeadsQ1
1324K 1%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR17
168KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR18
195.3K 1%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR30
1Adjdigikey-footprints:Rotary_Encoder_Switched_PEC11RSW1
1BLUE LEDLED_THT:LED_D3.0mmD4
1CD4013BEPackage_DIP:DIP-14_W7.62mm_SocketU2
1Display Headersputterizer:OLED_Header_SlimJ9
1GREEN LEDLED_THT:LED_D3.0mmD3
1LP2950-3.3_TO92digikey-footprints:TO-92-3_Formed_LeadsU5
1MAX7480Package_DIP:DIP-8_W7.62mm_Socket_LongPadsU6
1MB85RC256Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU7
1MC78L05_TO92Package_TO_SOT_THT:TO-92_Inline_WideU4
1MCP6002-E/PPackage_DIP:DIP-8_W7.62mm_SocketU8
1RED LEDLED_THT:LED_D3.0mmD14
1YELLOW LEDLED_THT:LED_D3.0mmD5
1small_logopanel:small_faceGR1

More from shannon-greenlight/spankulator

1
  • 2 layers60.6 × 24 mmDuDad, the printed circuit board in 3D

    DuDad

    shannon-greenlight/spankulator

    The Spankulator is a WiFi-enabled multi-function Eurorack module. Its main function is to generate a trio of coordinated analog and digital signals which can be used in an endless variety of ways.

    24 parts1

Similar boards

  • 2 layers34.9 × 35.6 mmEsque, the printed circuit board in 3D

    Esque

    alexmanuel27/Turbimeter_Citizen_science

    Design: Ing. Alex M. Rivera. Separated 19 October 2026.

    18 parts
  • 2 layers46 × 110 mmSputterizer, the printed circuit board in 3D

    Sputterizer

    cameronhotchkies/Sputterizer

    Synthesizer Module

    44 parts
  • 2 layers19.7 × 99.1 mmMain pcb, the printed circuit board in 3D

    Main pcb

    Testbild-synth/HAGIWO_arduino_oscillator

    4HP through hole version of the HAGIWO FM/additive/chord oscillator with mode switch and gain input.

    40 parts57MIT
  • 2 layers181.5 × 128.5 mmAndes 10HP, the printed circuit board in 3D

    Andes 10HP

    niektb/sluisbrinkie-eurorack-published

    Published Modules of the Sluisbrinkie project

    158 parts34
  • 4 layers158.5 × 57 mmGuitarAmplifier, the printed circuit board in 3D

    GuitarAmplifier

    RoMadrigal/GuitarAmplifier-PCB-IE0308

    Repositorio para el proyecto final del curso IE0308 sobre el diseño de una PCB de un amplificador para guitarra.

    48 parts3MIT
  • 2 layers100 × 60 mmLopielle, the printed circuit board in 3D

    Lopielle

    andreasimonetto/lopielle

    MIDI synth based on Yamaha OPLL FM synthesis sound chip (YM2413)

    49 parts2
  • 4 layers70.8 × 110 mmPipes sub, the printed circuit board in 3D

    Pipes sub

    shannon-greenlight/pipes

    8 Harmonic tracking oscillator

    303 parts2
  • 2 layers26 × 22 mmFaradometer, the printed circuit board in 3D

    Faradometer

    everyone-else-stole-the-good-usernames/ICLR-Faradometer

    Op Amp Capacitance to Voltage circuit

    22 parts1

Questions

How big is the Spankulator PCB?

It measures 60.4 × 110 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Spankulator use?

107 parts, built around the TL072CP, MCP6002-E/P, CD4013BE and MAX7480EPA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Spankulator KiCad files?

From the shannon-greenlight/spankulator repository on GitHub, at the commit this page was made from: the board is Spankulator-Hardware/Spankulator.kicad_pcb and its schematic DuDad/DuDad-Board/DuDad.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Spankulator design in my own project?

Its repository states no licence, so its author keeps all rights: ask shannon-greenlight before reusing the design.