Skip to the content
2 layers42.8 × 40.5 mmLcd, the printed circuit board in 3D

Just odds and ends I've saved for a rainy day

Size
42.8 × 40.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
36
Nets
63
Pads
176
Tracks, vias
287, 44
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
23 Oct 2022
Updated
1 Mar 2025

Overview

Lcd is an open-source printed circuit board by shades66, from the shades66/OddsAndEnds repository on GitHub. It is a 2-layer board of 42.8 × 40.5 mm with 36 parts on 63 nets, routed with 287 tracks and 44 vias.

It is built around the ESP32-WROVER, CH340G and AP2112K-3.3, with the WS2812B and S8050 among its other parts. Its parts include 8 diodes, 6 capacitors, 6 connectors, 5 resistors and 3 ICs. It belongs with the lEDs and displays boards and the ESP32 boards of this library.

Main components

5

README

README.md

OddsAndEnds

Just odds and ends I've saved for a rainy day

markisol.h - ESPHome library to allow use of BOFU BF-301 controlled blinds via RF transmitter

Philips-LivingColours-GEN2.jpeg - PCB from an old Philips LivingColours lamp which we have long since lost the remote for. Modified to work as part of my ESPHome setup. See key on image for the locations of the various control pins, I mounted a M5Stack Pico over the location the original CPU sat and ran wires to the 4 gpios for RED/GREEN/BLUE & Enable (as far as I can tell enables the powersupply section that feeds the LED's). I did try using the 3v feed that fed the microprocessor but it was not enough for the ESP32 to powerup. instead I used a mini buck converter with the inputs from a capacitor connected to the Power in port (18 Volts!!) which provided a 5v feed for the pico.

LivingColours.yaml - ESPHome config for the above circuit. See pins defined for the connections I made on the PCB. This setup is the basic rgb light config with two extras for on_turn_on/on_turn_off which switch the enable pin high/low.

ESPHome/clockhacking - Hacking a cheap AliExpress clock to work via ESPHome.

Parts

36
QtyValueFootprintReferences
6WS2812BMyLib:WS2812_2020D3, D4, D5, D6, D7, D8
510kResistor_SMD:R_0805_2012MetricR1, R2, R3, R4, R5
310uFCapacitor_SMD:C_0805_2012MetricC1, C3, C11
31uFCapacitor_SMD:C_0805_2012MetricC2, C4, C5
2LEDLED_SMD:LED_0603_1608MetricD1, D2
2S8050MyLib:SOT-23-1and2-swappedQ1, Q2
2SW_PushButton_Switch_SMD:SW_SPST_CK_RS282G05A3SW1, SW2
2SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP4, JP5
2SolderJumper_3_OpenJumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mmJP1, JP2
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U2
1CH340GPackage_SO:SOIC-16_3.9x9.9mm_P1.27mmU3
1Conn_01x03_MaleConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ6
1Conn_01x04_MaleConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ4
1Conn_01x07Connector_PinHeader_2.00mm:PinHeader_1x07_P2.00mm_VerticalJ1
1Conn_01x08_MaleConnector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ3
1Conn_01x09_MaleConnector_PinHeader_2.00mm:PinHeader_1x09_P2.00mm_VerticalJ5
1Conn_02x08_Counter_ClockwiseConnector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_VerticalJ2
1ESP32-WROVEResp-wrover:ESP32-WROVER-smallfeetU1

More from shades66/OddsAndEnds

5
  • 2 layers46.6 × 32.7 mmEsp32-s3-dev, the printed circuit board in 3D

    Esp32-s3-dev

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    48 parts
  • 2 layers42.8 × 45.7 mmLcd, the printed circuit board in 3D

    Lcd

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    32 parts
  • 4 layers29.3 × 12.1 mmESP32PICOV3, the printed circuit board in 3D

    ESP32PICOV3

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    26 parts
  • 2 layers39.3 × 16.4 mmLcd, the printed circuit board in 3D

    Lcd

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    17 parts
  • 2 layers15.1 × 16.2 mmLcd, the printed circuit board in 3D

    Lcd

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    4 parts

Similar boards

  • 2 layers110 × 31.5 mmMirobot, the printed circuit board in 3D

    Mirobot

    mirobot/mirobot-pcb

    The CAD files for the Mirobot PCB

    55 parts12
  • 2 layers76.2 × 76.2 mm4x4 platform, the printed circuit board in 3D

    4x4 platform

    jpconstantineau/NRF52-Board

    This Repository is a collection of NRF5x boards.

    71 parts100BSD-3-Clause
  • 2 layers52.8 × 71.8 mmESPBoosted, the printed circuit board in 3D

    ESPBoosted

    schoolllex/ESPBoosted

    A custom, feature-rich ESP32-WROOM-32 development board featuring built-in environmental sensors, power management, and expansion interfaces.

    51 parts
  • 4 layers81.4 × 90 mmSensor node, the printed circuit board in 3D

    Sensor node

    Kaiote-opensource/OpenHAP

    A low cost, opensource research tool with remote measurement capability for non invasive monitoring of household air pollution.

    127 partsMIT
  • 2 layers97.1 × 97.1 mmESP32 IMU Module V1.1, the printed circuit board in 3D

    ESP32 IMU Module V1.1

    shaun-lloyd/dev-ardupilot-obal

    ArduPi is an open hardware Raspberry Pi hat to run Ardupilot.

    87 parts2CC0-1.0
  • 2 layers47.5 × 20 mmDriver slim v1, the printed circuit board in 3D

    Driver slim v1

    brainsmoke/leddriver3d

    Renamed from esp32leddriver because it also contains code and PCBs for other MCUs

    17 parts11
  • 4 layers56 × 40 mmClocklet board, the printed circuit board in 3D

    Clocklet board

    samscam/clocklet

    A fancy clock implementation for ESP32

    36 parts2MIT

Questions

How big is the Lcd PCB?

It measures 42.8 × 40.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Lcd use?

36 parts, built around the ESP32-WROVER, CH340G, AP2112K-3.3 and WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Lcd KiCad files?

From the shades66/OddsAndEnds repository on GitHub, at the commit this page was made from: the board is ESP32Boards/V1.1/lcd.kicad_pcb and its schematic ESP32Boards/ESP32-Pico-V2-MiniPICO/ESP32PICOV3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Lcd design in my own project?

Its repository states no licence, so its author keeps all rights: ask shades66 before reusing the design.