Skip to the content
2 layersServo arm, the printed circuit board in 3D

Files for SemuBot PCB design.

Copper layers
2
Thickness
0.41 mm
Parts
74
Nets
63
Pads
278
Tracks, vias
626, 278
Pours
8
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
15 Jan 2024
Updated
29 Oct 2026

Overview

Servo arm is an open-source printed circuit board by SemuBot, from the SemuBot/semubot-electronics repository on GitHub. It is a 2-layer board with 74 parts on 63 nets, routed with 626 tracks and 278 vias.

Its parts include 27 capacitors, 14 resistors, 12 connectors, 8 ICs and 8 diodes. It belongs with the robots and motor control boards of this library.

README

wheelbase/README.md

Wheelbase

Overview

This project implements a 3-motor BLDC wheelbase controller using an STM32G4 microcontroller and three independent 3-phase gate-driver/MOSFET power stages, one per wheel.


Components

Microcontroller

  • STM32G474RET6 Main controller (LQFP-64).

BLDC Drivers

  • DRV8353FSRTAR (x3) 3-phase gate driver with integrated current-shunt amplifiers, one per motor.

MOSFETs

  • AON7262E (x18) N-channel MOSFETs for the power stage, 6 per motor (3-phase half-bridges).

Current Sensing

  • 9x 10 mΩ shunt resistors (2512 package), 3 per motor, read out through each DRV8353's integrated current-shunt amplifiers.

Voltage Regulation

  • RT9013-33GB 3.3V LDO regulator.

Power Input & Connectors

  • XT30PW-M Main DC power input connector.

  • MR30PW-M (x3) Motor phase power connectors, one per motor.

  • 10155435-00011LF (Amphenol) USB Type-C connector.

  • B5B-XH-A_LF(SN) (JST XH) (x6) 5-pin connectors for Hall/sensor inputs.

  • MTSW-104-09-L-S-400 (Samtec) 4-pin header, general purpose/debug I/O.

  • DS1013-10SSIB1 10-pin connector for general purpose I/O.

ESD / Overvoltage Protection

  • PRTR5V0U2X ESD protection for data lines (standard KiCad library part).
  • SMCJ33A 33V TVS diode for transient/overvoltage protection.
  • BZX84C3V3 3.3V zener diode.

Timing & Clock

  • X322516MLB4SI Crystal resonator for the STM32's HSE clock.

User Interface

  • 1x green + 4x red status LEDs.

Technical Summary

Power Stage

  • MOSFETs: 18x AON7262E (6 per motor)
  • Gate Drivers: 3x DRV8353FSRTAR
  • Current Sense Resistors: 9x 10mΩ (2512 package), read via the DRV8353's built-in current-shunt amplifiers (no separate current-sense ADC on this revision)

Parts

74
QtyValueFootprintReferences
17Vault:CAPC1608X08NC1, C2, C3, C4, C5, C6, C7, C8, C10, C11, C14, C15, C16, C19, C22, C25 +1
14Vault:RESC1608X04NR1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14
10Vault:CAPC1608X90X40NL10T20C12, C13, C17, C18, C20, C21, C23, C24, C26, C27
8Vault:DIOM1608X11ND1, D2, D3, D4, D5, D6, D7, D8
5Vault:SOIC127P600X175-8NU3, U5, U6, U7, U8
5Vault:691103110003J7, J8, J10, J11, J12
4, , ,
2Vault:Header-2.54-ZL201-05G-Footprint-1J1, J6
2Vault:SMTC-MTLW-104-07-X-S-125J3, J4
1Vault:SOT95P280X145-6NU4
1Vault:2_pin_f_2_54-Footprint-1J2
1Vault:LQFP50P1235X1235X165-64NU1
1Vault:Button 6mm tht-Footprint-1SW1
1Vault:USB3076-XX-X_revCJ5
1Vault:FP-C04-065-SL-IPC_BU2
1Vault:5mmScrewTerminal-Footprint-1J9

More from SemuBot/semubot-electronics

2
  • 4 layers160 × 80 mmPowerboard, the printed circuit board in 3D

    Powerboard

    SemuBot/semubot-electronics

    Files for SemuBot PCB design.

    130 parts
  • 4 layers110 × 90 mmWheelbase, the printed circuit board in 3D

    Wheelbase

    SemuBot/semubot-electronics

    Files for SemuBot PCB design.

    130 parts

Similar boards

  • 2 layers141.1 × 126.8 mmCalculator, the printed circuit board in 3D

    Calculator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    74 parts915
  • 2 layers49 × 44 mmSimple keeb reuser, the printed circuit board in 3D

    Simple keeb reuser

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    74 parts253GPL-3.0
  • 2 layers49 × 49 mmOSBMS Balancer Rev1 sot323, the printed circuit board in 3D

    OSBMS Balancer Rev1 sot323

    Teslafly/Dead-OpenBMS-dead

    A scalable, open source battery management system

    74 parts248
  • 2 layers72.4 × 72.4 mmSerialResonantFilter, the printed circuit board in 3D

    SerialResonantFilter

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    74 parts222
  • 2 layers58 × 65 mmSidechain mixer core, the printed circuit board in 3D

    Sidechain mixer core

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    74 parts222
  • 2 layers110 × 60 mmArduino Spot Welder, the printed circuit board in 3D

    Arduino Spot Welder

    KaeptnBalu/Arduino_Spot_Welder_V3

    This is the Kicad project for V3.1 The Arduino Board was not changed, only the Mosfet Board got a updgrade.

    74 parts207GPL-3.0
  • 2 layers51.5 × 89 mmMobo, the printed circuit board in 3D

    Mobo

    opulo-inc/feeder

    Source for LumenPnP Feeders

    74 parts202
  • 2 layers165.7 × 152.4 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-UART-Computer-1-2

    Legacy: Version 1 and 2 of my TTL-only CPU featuring UART I/O, an expansion port, 512KB SSD at up to 10MHz clock speed

    74 parts184

Questions

What parts does the Servo arm use?

74 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Servo arm KiCad files?

From the SemuBot/semubot-electronics repository on GitHub, at the commit this page was made from: the board is servo-arm/servo-arm.kicad_pcb and its schematic powerboard/hot-swap.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Servo arm design in my own project?

Its repository states no licence, so its author keeps all rights: ask SemuBot before reusing the design.