Skip to the content
4 layers50 × 65 mmLink mod lr brd, the printed circuit board in 3D

Open hardware for the Semtronik Link devices: ESP32-S3 base board, interface modules and enclosure. KiCad and Fusion sources, CERN-OHL-S v2.

Size
50 × 65 mm
Copper layers
4
Thickness
1.6 mm
Parts
18
Nets
19
Pads
70
Tracks, vias
179, 19
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
31 Aug 2026
Updated
12 Oct 2026

Overview

Link mod lr brd is an open-source printed circuit board by semtronik, from the semtronik/link-hardware repository on GitHub. It is a 4-layer board of 50 × 65 mm with 18 parts on 19 nets, routed with 179 tracks and 19 vias.

It is built around the WIO-SX1262 and M2.5. Its parts include 7 resistors, 3 connectors, 2 capacitors and 1 IC. It belongs with the interfaces and adapters boards of this library.

Main components

2

README

board/link-mod-lr-brd/README.md

link-mod-lr-brd

LoRa interface module of the Link platform. Plugged onto the base board, it makes a Link-LR: a LoRa P2P radio on 868/915 MHz.

Part of link-hardware. See the repository README for naming, versioning and release conventions.

Design

FunctionPart
LoRa radioSeeed Wio-SX1262 module (Semtech SX1262, TCXO, RF switch)
Base interface2×10 header, 2 mm pitch

The board is 60 × 50 mm. It carries the radio module and little else: decoupling, pull-ups and the connector to the base. The antenna leaves through a u.FL to SMA pigtail to the enclosure.

Connectors

RefRole
J2To the base board's J3: power (+3V3, +VSYS, +VNR), I²C and the eight module I/Os IO_MOD01–IO_MOD08, which carry the radio's SPI and control lines
J1, J31×8 sockets, 2.54 mm — not fitted on the Link-LR

J2 mates with the base's J3, the platform contract: its pinout, the mounting footprint and the 60 × 50 mm outline are what every interface module must satisfy.

Radio wiring

Module I/OSX1262
IO_MOD01MISO
IO_MOD02SCK
IO_MOD03MOSI
IO_MOD04RF_SW
IO_MOD05NRESET
IO_MOD06NSS
IO_MOD07DIO1 (interrupt)
IO_MOD08BUSY

The SX1262 drives the module's RF switch itself through DIO2, and powers its TCXO through DIO3; neither pin leaves the module. The module's RF_SW input must stay high for DIO2 to choose the direction: R3 (10 k to +3V3) holds it, so the firmware leaves that pin alone.

Status

Pre-production (0.x). Revision 0.2.0 is validated on our own bench; all interfaces may still change without a MAJOR bump.

Files

Design sources are the KiCad project in this folder. outputs/ holds the fab-agnostic exports of the last freeze — schematic PDF, BOM, position file, gerbers and STEP.

They are regenerated by running outputs.kicad_jobset from the KiCad project window. Output names carry the revision read from the schematic title block, so they cannot drift from the sources.

Parts

18
QtyValueFootprintReferences
40RResistor_SMD:R_0805_2012MetricR4, R5, R6, R7
4M2.5MountingHole:MountingHole_2.7mm_M2.5H1, H2, H3, H4
310kResistor_SMD:R_0603_1608MetricR1, R2, R3
2Socket-2.54mm-VRConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ1, J3
10.1uFCapacitor_SMD:C_0603_1608MetricC2
110uFCapacitor_SMD:C_0805_2012MetricC1
1Header-2x10-2mm-VRConnector_PinHeader_2.00mm:PinHeader_2x10_P2.00mm_VerticalJ2
1Wio-SX1262RF_Lora:WioSX1262U1
1~Board:BRD-MIKROE-SBRD1

More from semtronik/link-hardware

1
  • 4 layers94 × 65 mmLink base brd, the printed circuit board in 3D

    Link base brd

    semtronik/link-hardware

    Open hardware for the Semtronik Link devices: ESP32-S3 base board, interface modules and enclosure. KiCad and Fusion sources, CERN-OHL-S v2.

    115 parts

Similar boards

  • 2 layers79 × 30 mmLIA, the printed circuit board in 3D

    LIA

    JGAguado/LIA

    Low-power pet tracking platform built around Meshtastic and LoRa mesh networking

    81 parts29
  • 4 layers42.5 × 32 mmMeshlet, the printed circuit board in 3D

    Meshlet

    dj505/Meshlet

    A feature-packed LoRa mesh network node

    101 parts7
  • 2 layers50 × 60 mmGO, the printed circuit board in 3D

    GO

    Ainacteru/GO

    The source code for the GO PCB

    72 parts1
  • 2 layers40 × 50 mmSensor Station, the printed circuit board in 3D

    Sensor Station

    BeeEyeIoT/sensor-station-board

    Complete KiCAD project for a sensor data collection station

    39 parts
  • 6 layers43 × 82.4 mmCmd z5, the printed circuit board in 3D

    Cmd z5

    befinitiv/cmd-z5-pager

    Replacement PCB & Software to turn Sony CMD-Z5 into a Meshtastic/Lorawan pager

    120 parts
  • 2 layers79.3 × 46.4 mmRook, the printed circuit board in 3D

    Rook

    edgecollective/rook

    Rook is an open hardware radio board from Edge Collective. It is built for nodes that sit outdoors on a battery and keep working: mesh repeaters, remote sensors, and anything else that needs to send data a long way…

    51 parts
  • 2 layers65.5 × 30.3 mmLoraHat, the printed circuit board in 3D

    LoraHat

    joaouzeda/LoRa-Esp32_RaspbeeryPi0W_Hat

    Project Description An Esp32 with LoRa to connect with a Raspberry Pi Zero W using serial Pins.

    9 parts
  • 2 layers17.8 × 21.4 mmSeeed xiao esp32s3-expander, the printed circuit board in 3D

    Seeed xiao esp32s3-expander

    lucg/seeed-xiao-esp32s3-expander

    An expansion board for the Seeed Studio XIAO ESP32-S3 (Plus) using the B2B connector

    15 partsCC-BY-SA-4.0

Questions

How big is the Link mod lr brd PCB?

It measures 50 × 65 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Link mod lr brd use?

18 parts, built around the WIO-SX1262 and M2.5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Link mod lr brd KiCad files?

From the semtronik/link-hardware repository on GitHub, at the commit this page was made from: the board is board/link-mod-lr-brd/link-mod-lr-brd.kicad_pcb and its schematic board/link-base-brd/core.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Link mod lr brd design in my own project?

Its repository states no licence, so its author keeps all rights: ask semtronik before reusing the design.