

Pico dram tester
Raspberry Pi Pico 2 Vintage DRAM Tester
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 47
- Nets
- 67
- Pads
- 273
- Tracks, vias
- 927, 205
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 3 Oct 2024
- Updated
- 26 Aug 2026
Overview
Pico dram tester is an open-source printed circuit board by schlae, from the schlae/pico-dram-tester repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 100 × 100 mm with 47 parts on 67 nets, routed with 927 tracks and 205 vias.
It is built around the RFM-0505S. Its parts include 12 resistors, 10 capacitors, 9 ICs, 3 connectors and 2 switches. It belongs with the RP2040 and RP2350 boards of this library.
Main components
1README
README.mdPico DRAM Tester
Having trouble with your old-school DIP dynamic RAM chips? Here's a simple RAM tester that will give you a definitive pass or fail for a variety of chips.
New rev 3 now available! New features include:
- USB-C power connector with PD resistors
- Universal encoder wiring supports Bourns and Panasonic style encoders
- Through-hole footprint for the Pico2 to ease soldering

Benefits
- Tests RAM at full speed so you can feel confident about a chip that passes.
- Easy to construct with widely-available parts. No surface mount chips.
- Low cost
- Built-in DC-DC modules generate extra voltages required by 4116-class chips
- Can be operated from a bench supply for voltage margin testing
Supported Devices
- 4027 (4K x 1)
- 4108 (8K x 1 that are 4116s with only half test good: MK4108, TMS4108, etc)
- 4116 (16K x 1)
- 4132 (32K x 1, piggyback)
- 4132 (32K x 1 that are 4164s with only half tested good: TMS4532, M3732)
- 4164 (64K x 1)
- 41128 (128K x 1, piggyback)
- 41256 (256K x 1)
- 4416 (16K x 4)
- 4464 (64K x 4)
- 44256 (256K x 4)
Out of scope
- SRAM, DRAM chips larger than 1MBit
- Logic chips
Construction
The board is a simple 2-layer board, 100mm x 100mm, and 1.6mm thick. Fabricate at your favorite vendor in any color you wish.
You may populate the board only with the sockets for devices you plan to use, or you may populate all the sockets. You can try substituting the sockets with standard IC sockets, but I recommend ZIF sockets which are much easier to use. Why so many sockets? It saves you from having to install dozens of pin control transistors required to make a tester work with a single universal socket.
If you want to populate the USB-C connector, do it first before any other components. It makes it much easier to access the surface-mount pins along the edge with a soldering iron.
Populate Q1, U7, U8, R2, R3, R4, and R5 if you would like to test 4116 and 4132 devices without requiring an external -5V and +12V power supply.
If you want to provide the -5V, +5V, and +12V power from your bench supply, then you may leave those components off of the board and connect your power leads to the -5V, +5V, and +12V test points. If you don't plan to test 4116 or 4132 chips, then you can safely leave out those components.
The LCD display is nominally the Adafruit 4383 which is to be installed at location J1 (U9 is not required when using this display). You can also use cheaper devices available from Aliexpress and others. They are 8-pin LCD displays sold as 1.14" 135x240 IPS ST7789 modules. Install this display at position J2. You may also need to add the voltage monitor at position U9.
For several reasons, this board requires a Pico 2 microcontroller board and will not work at all with the Pico 1.
If you use a Bourns-style encoder, you will need to solder across the jumper on the back of the board. This is the most common type of cheaply-available encoders, so you probably want to do this. Otherwise, for Panasonic-style encoders, leave this open.
After installing all the components and inspecting the board for accidental short circuits, connect the Pico 2 via the USB connector to a computer. The device should power up and appear as a USB mass storage device. Copy the prebuilt firmware file pmemtest.uf2 to this device, and the Pico 2 will program itself. Reset the power and you should see a menu of chips on the LCD screen.
Using the DRAM Tester
Before starting, connect the tester to a power source:
- If you did not install U7 and U8, connect a bench supply to the GND, -5V, +5V, and +12V test points. Connect the Pico 2 USB jack to a power adapter or computer.
- If you installed U7 and U8, connect a 5V bench supply to the 5VIN and GND test points. Instead of a bench supply, you could connect the Pico 2 USB jack to a power adapter, but you won't be able to control the voltage. A computer often has a much lower voltage and you may fail RAM chips that actually function at 5V.
- Install the chip in the socket designated for that type of memory chip, following the pin 1 orientation (the pin 1 notch faces the ZIF socket lever). Note that some of the sockets are used for several types of memory.
- Rotate the selection knob until the correct part number is highlighted, and push down on the top of the selection knob (it's also a button!)
- If you make a mistake, press the button to the left of the selection knob to go back.
- After selecting a part, you need to pick the correct speed grade to run the test. Often the speed grade is marked on the chip as a suffix. For example, -15 typically means 150ns. If you're not sure, pick the slowest speed.
- If you are using an external bench power supply to supply -5V and +12V, turn it on now. If you soldered in the on-board voltage converter modules, you don't need to do anything. Push the top of the selection knob to continue.
- The test runs. You will see a red "X" if the test fails or a green checkmark if the test passes.
- You can rerun the test immediately by pushing down on the top of the selection knob. Or go back to the menu by pushing the button to the left.
Note: The visualization pane on the left is just for entertainment and doesn't really represent bad bits.
Technical Details
The Pico 2 microcontroller (RP2350) has built-in high-speed PIO processors which are overclocked to 300MHz. This means that the DRAM timing can be set to a resolution of 3.3ns. The RAM test runs on the second CPU core, decoupling it from the GUI, which runs on the first CPU core.
RAM testing can be surprisingly complicated. There are many kinds of failures:
- Stuck-at fault - a cell is stuck at a 1 or a 0
- Stuck-open fault - a cell isn't connected (input or output)
- Transition fault - a cell can't go from one state to another (1 to 0 or 0 to 1)
- Data retention fault - a cell flips after a time delay
- Coupling fault - the state of one cell affects the state of another
- Neighborhood pattern sensitive fault - a specific pattern in nearby cells causes a cell to flip
- Address decoder fault - cells may be isolated, or multiple cells accessed at the same address, or multiple addresses may access a single cell
There are a number of "traditional" RAM tests such as the checkerboard or walking 1/0, but these tests can be slow and don't have precise coverage over all failure modes. The Pico DRAM Tester uses more modern testing algorithms:
- March-B. This is a sequence of linear reads and writes designed to catch address faults, stuck-at faults, transition faults, and coupling faults.
- Pseudorandom test. This test loads a pseudorandom number sequence into the memory, reads it back, and checks to make sure it didn't change. The test is repeated with 64 different pseudorandom patterns to enhance coverage. The patterns are identical between runs, making the test repeatable. The test only uses pseudorandom data and does not randomize the address. This test can detect many pattern-sensitive faults.
- Refresh test. This test loads a pattern into the memory, waits for a time delay, and then tries to read it back. The time delay is longer than a typical refresh rate. This test can detect data retention faults. The default delay of 32ms may be adjusted by editing the line
return refresh_subtest(addr_size, bits, 32000);with a new value, in microseconds.
Tips and Tricks
- Use a multimeter to check the voltage on the leftmost 5V test point to make sure your AC adapter is up to snuff! Lower voltages will cause memory chips to perform poorly and fail to meet their speed grade.
- Have a memory chip that may be marginal? Try using a heat gun (without melting the board!) to warm it up and make it fail. Cold spray or an inverted air duster can help you hit the low temperature range.
- Suspect contact problems with the sockets or the memory chip leads? Put it in the socket, close the lever, and then slide it sideways, which will clean the contacts and establish a better connection.
Troubleshooting
Check your solder connections. Does the Pico 2 board show up in bootloader mode when you plug it into a computer?
The Pico DRAM Tester uses an overclocked Pico 2 configuration.
Some Pico 2 boards may not work well at 300MHz, crashing or not drawing the GUI on the screen correctly.
You may be able to get it working by editing pmemtest.c, find the line vreg_set_voltage(VREG_VOLTAGE_1_20); and change the voltage setting to VREG_VOLTAGE_1_25.
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. See https://creativecommons.org/licenses/by-sa/4.0/.
Parts
47| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 0.1uF | Passive:CAPAC200 | C2, C3, C4, C5, C6, C7, C8, C9, C10 |
| 6 | 4.7K | Passive:RESA500 | R4, R6, R7, R8, R9, R10 |
| 4 | 33 | Resistor_THT:R_Array_SIP8 | RN1, RN2, RN3, RN4 |
| 2 | 5.1K | Passive:RESA500 | R11, R12 |
| 2 | 680 | Passive:RESA500 | R2, R3 |
| 1 | -5V | TestPoint:TestPoint_Keystone_5005-5009_Compact | TP4 |
| 1 | 100 | Passive:RESA500 | R5 |
| 1 | 10uF | Passive:CAPAE200P500X1100 | C1 |
| 1 | 12V | TestPoint:TestPoint_Keystone_5005-5009_Compact | TP3 |
| 1 | 33 | Passive:RESA500 | R1 |
| 1 | 4116 | Socket:DIP_Socket-16_W4.3_W5.08_W7.62_W10.16_W10.9_3M_216-3340-00-0602J | U2 |
| 1 | 4132 | Socket:DIP_Socket-18_W4.3_W5.08_W7.62_W10.16_W10.9_3M_218-3341-00-0602J | U3 |
| 1 | 4164/41128/41256 | Socket:DIP_Socket-16_W4.3_W5.08_W7.62_W10.16_W10.9_3M_216-3340-00-0602J | U4 |
| 1 | 4416/4464 | Socket:DIP_Socket-18_W4.3_W5.08_W7.62_W10.16_W10.9_3M_218-3341-00-0602J | U5 |
| 1 | 44256 | Socket:DIP_Socket-20_W4.3_W5.08_W7.62_W10.16_W10.9_3M_220-3342-00-0602J | U6 |
| 1 | 5V | TestPoint:TestPoint_Keystone_5005-5009_Compact | TP1 |
| 1 | 5VIN | TestPoint:TestPoint_Keystone_5005-5009_Compact | TP5 |
| 1 | APX803S | Package_TO_SOT_SMD:SOT-23_Handsoldering | U9 |
| 1 | BACK | Button_Switch_THT:SW_SPST_Omron_B3F-50xx | SW2 |
| 1 | DCDC_ITR03 | Active:DCDC_ITR03 | U7 |
| 1 | GND | TestPoint:TestPoint_Keystone_5005-5009_Compact | TP2 |
| 1 | PICO2 | Active:Pico2_PTH | U1 |
| 1 | POWER | Connector_USB:USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_Horizontal | J3 |
| 1 | RFM-0505S | Active:DCDC_ITR03 | U8 |
| 1 | RotaryEncoder_Switch | Switch:ENCODER_SW_UNIV | SW1 |
| 1 | SUP53P06-20-E3 or equiv | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | TFT 4383 | Active:ADAFRUIT_4383 | J1 |
| 1 | TYPE | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | mrd_114_ips_lcd_8p | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2 |
Similar boards
- 4 layers80 × 100 mm

- 4 layers100 × 50 mm

Psu ext
PSU-Ext-Org/psu-ext-hardware
A repository to store PSU-EXT hardware design assets, schematics, circuit diagrams, CAD files and manufacturing data.
137 parts9CERN-OHL-S-2.0 - 4 layers165 × 50 mm

- 2 layers127 × 100.3 mm

Cross point exp brd mini red2-sjmp
damercer/Cross-Point-Project
A Software Configurable Solderless Breadboard
130 parts3 - 2 layers59.4 × 32.3 mm

- 6 layers170 × 172.2 mm

Esc rev b
iamdarshg/drone-arm
Reworked cheaper, maybe faster but less redundant drone controller.
681 parts2 - 4 layers68.5 × 53.3 mm

- 2 layers80 × 55 mm

RPI Pico Oscilloscope
Alexou1209/RPI-Pico-oscilloscope-and-logic-analyzer
A pocket sized Oscilloscope and logic Analyzer made using a Raspberry Pi Pico 2 (RP2350) and sigrok-pico firmware
42 parts
Questions
How big is the Pico dram tester PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pico dram tester use?
47 parts, built around the RFM-0505S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pico dram tester KiCad files?
From the schlae/pico-dram-tester repository on GitHub, at the commit this page was made from: the board is pico-dram-tester.kicad_pcb and its schematic pico-dram-tester.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pico dram tester design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).