

Reverse engineered disposable v a p e boards
- Size
- 37.8 × 16.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 54
- Nets
- 43
- Pads
- 167
- Tracks, vias
- 497, 104
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 24 Sep 2025
- Updated
- 1 Nov 2025
Overview
Tmy is an open-source printed circuit board by schlae, from the schlae/VapeRE repository on GitHub. It is a 2-layer board of 37.8 × 16.2 mm with 54 parts on 43 nets, routed with 497 tracks and 104 vias.
It is built around the CS32F031K8V6-RA, TP4054 and DTC143E, with the 12P10-VB, CJE3139K and LMUN2232LT1G among its other parts. Its parts include 15 resistors, 7 capacitors, 5 transistors, 4 ICs and 3 connectors.
Main components
6CS32F031K8V6-RA
QFN-32(4x4)QFN-32(4x4) Microcontrollers (MCU/MPU/SOC) ROHSCHIPSEAMicrocontrollers (MCU/MPU/SOC)TP4054
SOT-23-5L-40℃~+85℃ 1 25uA 4.2V 4.2V~6.5V 500mA Charging IC Lithium Battery Not supported 恒流充电、恒压充电、涓流充电、自动再充电、充电终止、可编程充电电流、软启动、欠压锁定 SOT-23-5L Battery Management ROHSUMWBattery ManagementDTC143E
-1 NPN 100mA 100nA 350mW 50V NPN - Bipolar (BJT)onsemiBipolar (BJT)12P10-VB
TO-252MOSFETsVBsemi ElecCJE3139K
SOT-523-55℃~+150℃ 1 P-Channel 150mW 15pF 170pF 20V 350mV 520mΩ@4.5V 660mA SOT-523 MOSFETs ROHSJiangsu Changjing Electronics Technology (CJ)MOSFETsLMUN2232LT1G
SOT-23-55℃~+150℃ 1 NPN (Pre-Biased) 1.2 100mA 15 200mV 246mW 250mV 50V 50nA 6.1kΩ NPN SOT-23 Digital Transistors ROHSLeshan Radio (LRC)Digital Transistors
README
README.mdReverse Engineered Vape Circuit Boards
Disposable vapes show up all the time in e-waste and are often found as litter at the side of the road (shame!) but they contain some useful components that can be reused by the cost-conscious hacker.
Note: Wear gloves when handling used devices and don't allow the vape liquid to contact your skin or eyes.
I've reverse engineered a number of different brands and placed the schematics and layout files in this repository. The summary table below is a good starting point.
Many of the vapes have debugging connections accessible through the USB-C charging cable interface, typically SWD on the CC pins, so you may be able to reprogram the vape without even opening up the case.
| Brand | PCB ID | Display | MCU | NOR flash | Battery IC | LDO regulator | Debug | Other Notes |
|---|---|---|---|---|---|---|---|---|
| (Unknown) | FT03 V3.0 | LCD | CHIPSEA F031K8V6 | GT 25Q32A | PC3221 | CJ6330 | SWD on CC lines. UART test points. | Touch IC TTP223. Pushbutton. 3 heater outputs with feedback. |
| Flum Mello | TMY_0118470101_V04 | LCD | CHIPSEA F031K8V6 | ZB 25VQ32 | TP4054 | CJ6330 | SWD on CC lines. | One heater output with feedback. |
| Rama 16000 | YK761-VP9012-A | LCD | BlueX BX2400 or RF01 | Puya PY25Q64 | CST4056 | CJ6330 | Test points for SWD | One heater with feedback. Bluetooth (!) |
| GeekBar Pulse 15000 | BD0027-USB_V1.5 | Blue and RGB LEDs | Puya PY32F030EK28 | None | LP4068 | None | SWD on CC lines. | 3-position slide switch. Two heaters with feedback. |
| Lost Mary MO20000 Pro | STW2915 V1.7 | LCD | Pya PY32F030EK28 | Puya PY32Q64 | LP4068 | CJ6330 (?) | SWD on CC lines. | |
| GeekBar Pulse X Jam | BD0061 | LCD and blue LEDs, PLS916H driver IC | Puya PY32F030EK28 | None | LR5112/LR5108 | None | SWD on CC lines. |
I also have firmware running on the Lost Mary MO20000 Pro that could be modified to run on other vapes with the same PY32F030 microcontroller.
License
All the reverse engineered hardware data is provided under the Creative Commons Attribution-ShareAlike 4.0 International license.
Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 10K | Resistor_SMD:R_0402_1005Metric | R2, R4, R9, R15 |
| 4 | 1K | Resistor_SMD:R_0402_1005Metric | R1, R6, R10, R13 |
| 3 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C4, C5, C7 |
| 2 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C3, C6 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R11, R12 |
| 2 | B+ | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP17 |
| 2 | DTC143E | Package_TO_SOT_SMD:SOT-523 | Q2, Q3 |
| 1 | 0.01uF | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | 1.8K | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 12P10V | Package_SON:Texas_DQK | Q1 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 2 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 2 | Resistor_SMD:R_0402_1005Metric | R8 |
| 1 | 2K | Resistor_SMD:R_0402_1005Metric | R14 |
| 1 | 30K | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | B- | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | BL_A | TestPoint:TestPoint_Pad_D1.0mm | TP12 |
| 1 | BL_K | TestPoint:TestPoint_Pad_D1.0mm | TP11 |
| 1 | CJE3139K | Package_TO_SOT_SMD:SOT-523 | Q4 |
| 1 | CLK | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | CS32F031K8V6 | Package_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.9x2.9mm | U1 |
| 1 | Conn_01x03 | Active:MIC_3P_Alt | MIC1 |
| 1 | DI | TestPoint:TestPoint_Pad_D1.0mm | TP10 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP14 |
| 1 | H- | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | J2 |
| 1 | H- | TestPoint:TestPoint_Pad_D1.0mm | TP16 |
| 1 | H1+ | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | J1 |
| 1 | H1+ | TestPoint:TestPoint_Pad_D1.0mm | TP15 |
| 1 | LCD | VapeRE:UNK_FPC_1x10-1MP_P0.5mm_Horizontal | J3 |
| 1 | LDO | Active:SOT95P230X117-3 | U4 |
| 1 | LMUN2232LT1G | Package_TO_SOT_SMD:SC-59 | Q5 |
| 1 | PA1 | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | PA10 | TestPoint:TestPoint_Pad_D1.0mm | TP13 |
| 1 | PA2 | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | PA3 | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | PA4 | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | Polyfuse_Small | Fuse:Fuse_0603_1608Metric | F1 |
| 1 | SWCLK | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | SWDIO | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | TP4054 | Package_SO:TSOP-5_1.65x3.05mm_P0.95mm | U3 |
| 1 | USB_C_Receptacle_PowerOnly_6P | VapeRE:USB_C_Receptacle_TYPE-C-VERT | USB1 |
| 1 | ZB 25VQ32 | Package_SON:Winbond_USON-8-1EP_3x2mm_P0.5mm_EP0.2x1.6mm | U2 |
More from schlae/VapeRE
5- 4 layers34.9 × 20.3 mm

- 4 layers40.9 × 23.7 mm

- 2 layers

- 2 layers79.3 × 20.7 mm

- 2 layers31.1 × 19 mm

Similar boards
- 4 layers40.6 × 17.8 mm

- 2 layers50.3 × 50 mm

- 2 layers135 × 35 mm

Printhead pcb
Fiberprinter/fiberprinter-electronics
Fiberelectronics Control every pulse, master every micron
78 parts4 - 2 layers68.9 × 121.6 mm

- 2 layers102.9 × 116.7 mm

PocketBeagleCommandStation
RobertPHeller/CommandStationsAndBoosters
Command Stations and Boosters
133 parts - 4 layers74 × 104 mm

- 2 layers83.2 × 40 mm

- 2 layers53 × 53 mm

Hair electrolysis machine
zoemaestra/hair-electrolysis-machine-usb-c
A fork of scd31's hair electrolysis machine but with USB-C and optimised for cheaper assembly with JLCPCB
83 parts168CERN-OHL-P-2.0
Questions
How big is the Tmy PCB?
It measures 37.8 × 16.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Tmy use?
54 parts, built around the CS32F031K8V6-RA, TP4054, DTC143E and 12P10-VB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tmy KiCad files?
From the schlae/VapeRE repository on GitHub, at the commit this page was made from: the board is TMY/tmy.kicad_pcb and its schematic BD0027/BD0027.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tmy design in my own project?
Its repository states no licence, so its author keeps all rights: ask schlae before reusing the design.