

BD0027
Reverse engineered disposable v a p e boards
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 81
- Nets
- 76
- Pads
- 277
- Tracks, vias
- 989, 154
- Pours
- 18
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 24 Sep 2025
- Updated
- 1 Nov 2025
Overview
BD0027 is an open-source printed circuit board by schlae, from the schlae/VapeRE repository on GitHub. It is a 2-layer board with 81 parts on 76 nets, routed with 989 tracks and 154 vias.
It is built around the PY32F030K28T6, LP4068B5F and SI2305. Its parts include 32 resistors, 16 diodes, 6 connectors, 5 capacitors and 5 transistors.
Main components
3PY32F030K28T6
LQFP-32(7x7)64KB FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSPUYAMicrocontrollers (MCU/MPU/SOC)LP4068B5F
SOT-23-5-20℃~+85℃ 1 1uA 4.2V 4.5V~9V 800mA Charging IC Lithium Battery SOT-23-5 Battery Management ROHSLOWPOWERBattery ManagementSI2305
SOT-23-55℃~+150℃ 1 P-Channel 12V 15nC@4.5V 290pF 350mW 4.1A 45mΩ@4.5V 740pF 900mV SOT-23 MOSFETs ROHSGuangdong HottechMOSFETs
README
README.mdReverse Engineered Vape Circuit Boards
Disposable vapes show up all the time in e-waste and are often found as litter at the side of the road (shame!) but they contain some useful components that can be reused by the cost-conscious hacker.
Note: Wear gloves when handling used devices and don't allow the vape liquid to contact your skin or eyes.
I've reverse engineered a number of different brands and placed the schematics and layout files in this repository. The summary table below is a good starting point.
Many of the vapes have debugging connections accessible through the USB-C charging cable interface, typically SWD on the CC pins, so you may be able to reprogram the vape without even opening up the case.
| Brand | PCB ID | Display | MCU | NOR flash | Battery IC | LDO regulator | Debug | Other Notes |
|---|---|---|---|---|---|---|---|---|
| (Unknown) | FT03 V3.0 | LCD | CHIPSEA F031K8V6 | GT 25Q32A | PC3221 | CJ6330 | SWD on CC lines. UART test points. | Touch IC TTP223. Pushbutton. 3 heater outputs with feedback. |
| Flum Mello | TMY_0118470101_V04 | LCD | CHIPSEA F031K8V6 | ZB 25VQ32 | TP4054 | CJ6330 | SWD on CC lines. | One heater output with feedback. |
| Rama 16000 | YK761-VP9012-A | LCD | BlueX BX2400 or RF01 | Puya PY25Q64 | CST4056 | CJ6330 | Test points for SWD | One heater with feedback. Bluetooth (!) |
| GeekBar Pulse 15000 | BD0027-USB_V1.5 | Blue and RGB LEDs | Puya PY32F030EK28 | None | LP4068 | None | SWD on CC lines. | 3-position slide switch. Two heaters with feedback. |
| Lost Mary MO20000 Pro | STW2915 V1.7 | LCD | Pya PY32F030EK28 | Puya PY32Q64 | LP4068 | CJ6330 (?) | SWD on CC lines. | |
| GeekBar Pulse X Jam | BD0061 | LCD and blue LEDs, PLS916H driver IC | Puya PY32F030EK28 | None | LR5112/LR5108 | None | SWD on CC lines. |
I also have firmware running on the Lost Mary MO20000 Pro that could be modified to run on other vapes with the same PY32F030 microcontroller.
License
All the reverse engineered hardware data is provided under the Creative Commons Attribution-ShareAlike 4.0 International license.
Parts
81| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | LED_ABGR | LED_SMD:LED_SK6812_EC15_1.5x1.5mm | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8, LED9, LED10, LED11, LED12, LED13, LED14, LED15, LED16 |
| 9 | 56 | Resistor_SMD:R_0402_1005Metric | R1B1, R2B1, R23, R24, R25, R26, R27, R28, R29 |
| 4 | 10K | Resistor_SMD:R_0402_1005Metric | R12, R13, R18, R34 |
| 4 | 1K | Resistor_SMD:R_0402_1005Metric | R4, R5, R10, R14 |
| 3 | 100K | Resistor_SMD:R_0402_1005Metric | R9, R11, R19 |
| 3 | 2N7002 | Package_TO_SOT_SMD:SOT-523 | Q3, Q4, Q5 |
| 3 | ? | Resistor_SMD:R_0805_2012Metric | R31, R32, R33 |
| 3 | ? | Connector_Pin:Pin_D1.2mm_L10.2mm_W2.9mm_FlatFork | J2, J3, J4 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 2.4K | Resistor_SMD:R_0402_1005Metric | R6, R17 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | Conn_01x11 | Connector_PinHeader_1.00mm:PinHeader_1x11_P1.00mm_Vertical | CN1, CN2 |
| 2 | Si2305 | Active:SOT95P230X117-3 | Q1, Q2 |
| 1 | 0 | Resistor_SMD:R_0402_1005Metric | R21 |
| 1 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | 100 | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 1M | Resistor_SMD:R_0402_1005Metric | R16 |
| 1 | 2.2 | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | ? | Capacitor_SMD:C_0402_1005Metric | C31 |
| 1 | B+ | TestPoint:TestPoint_Pad_D1.5mm | TP10 |
| 1 | BA+ | TestPoint:TestPoint_Pad_D1.5mm | TP6 |
| 1 | DNI | Resistor_SMD:R_0402_1005Metric | R22 |
| 1 | G | Fuse:Fuse_0603_1608Metric | FS1 |
| 1 | LED_OLW4710Z-DZ | VapeRE:OLW4710Z-DZ | S1 |
| 1 | LP4068 | Package_SO:TSOP-5_1.65x3.05mm_P0.95mm | U1 |
| 1 | PY32F030K2 | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U2 |
| 1 | SW_DP3T | VapeRE:SW_DP3T_SMD | SW1 |
| 1 | T5V | TestPoint:TestPoint_Pad_D1.5mm | TP11 |
| 1 | T5V1 | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | TB+ | TestPoint:TestPoint_Pad_D1.5mm | TP9 |
| 1 | TB1 | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | TB2 | TestPoint:TestPoint_Pad_D1.5mm | TP3 |
| 1 | TGND | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | TGND1 | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | TU1 | TestPoint:TestPoint_Pad_D1.5mm | TP7 |
| 1 | TU2 | TestPoint:TestPoint_Pad_D1.5mm | TP8 |
| 1 | USB_C_Receptacle_PowerOnly_6P | VapeRE:USB_C_Receptacle_TYPE-C-VERT | J1 |
| 1 | Unknown Mic Amp | Package_TO_SOT_SMD:SOT-23-5 | U3 |
More from schlae/VapeRE
5- 4 layers34.9 × 20.3 mm

- 4 layers40.9 × 23.7 mm

- 2 layers79.3 × 20.7 mm

- 2 layers37.8 × 16.2 mm

- 2 layers31.1 × 19 mm

Similar boards
- 2 layers68.8 × 53.6 mm

- 4 layers48.5 × 33.5 mm

- 2 layers92 × 73.1 mm

Open squib esp wroom v2
chromalock/OpenSquib
Open-Sourced implementation of a PCB-Based Squib
37 parts17CC0-1.0 - 2 layers45 × 45 mm

- 2 layers60.8 × 31 mm

- 2 layers449.1 × 144.3 mm

Chili master
silitekmodder/Chili-master
Re-uploaded Chili PCB for the Cherry G80-3000/G81-3000 series keyvboards (NOT MINE)
465 parts3CC0-1.0 - 2 layers80 × 80 mm

Kubisat power v2
gredzikk/kubisat
Hardware and software of cubesat model for engineering thesis
82 parts2MIT - 4 layers68.6 × 53.3 mm

Questions
What parts does the BD0027 use?
81 parts, built around the PY32F030K28T6, LP4068B5F and SI2305. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BD0027 KiCad files?
From the schlae/VapeRE repository on GitHub, at the commit this page was made from: the board is BD0027/BD0027.kicad_pcb and its schematic BD0027/BD0027.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BD0027 design in my own project?
Its repository states no licence, so its author keeps all rights: ask schlae before reusing the design.