

Levelshift tunable ahct
A universal level shifter for driving different types of cable
- Size
- 71.8 × 25.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 12
- Nets
- 10
- Pads
- 32
- Tracks, vias
- 60, 6
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 1 Apr 2026
- Updated
- 7 May 2026
Overview
Levelshift tunable ahct is an open-source printed circuit board by saratoga4, from the saratoga4/levelshift_tunable_ahct repository on GitHub. It is a 2-layer board of 71.8 × 25.2 mm with 12 parts on 10 nets, routed with 60 tracks and 6 vias.
It is built around the 74AHCT1G125SE and 3386P-1-101TLF. Its parts include 4 capacitors, 2 resistors, 2 ICs and 2 connectors. It belongs with the interfaces and adapters boards of this library.
Main components
274AHCT1G125SE
SOT-353-40℃~+125℃ 1 1 4.5V~5.5V 4.7ns@5V,50pF 40uA 74AHCT 8mA 8mA Schmitt trigger Tri-State Unidirectional SOT-353 Buffers, Drivers, Receivers, Transceivers ROHSDiodes IncorporatedBuffers, Drivers, Receivers, Transceivers3386P-1-101TLF
插件-3P,9.5x9.5mm1 100Ω 500mW ±10% ±100ppm/℃ 插件-3P,9.5x9.5mm Potentiometers, Variable Resistors ROHSBournsPotentiometers & Variable Resistors
README
README.mdUniversal level shifter

This project contains KiCAD files for a 3-3V->5V level shifter that can drive arbitrary impedance lines using a potentiometer to continuously adjust impedance. Labels are provided for typical wire types, including 3-wire cable, 75 ohm coax, 100 ohm twisted pair, and higher impedance 2-wire cables.
BOM
A bill of materials with Digikey part numbers is provided: bom/ibom.html
Instructions
By rotating the knob to the appropriate position, you can drive a variety of cable types without requiring an oscilloscope to fine tune the resistor value. Just turn until the strip stops glitching.
Testing

20m of 3-wire 20AWG LED cable from Amazon worked extremely well.

Power cables (which are not made to carry data) are much harder to drive. 72m of cable is definitely pushing it, but works without data corruption. The knob position is a little off due to the thickness of the cables, which lowers their impedance a little vs typical thinner data cable.
Wiring for long distance
Most addressable LEDs use single-ended signaling, meaning that the data ground and power ground share a wire. For very long runs (>10s of meters) or at very high current, voltage drop due to current in the ground wire can cause data corruption by lifting the ground voltage at the far end of the cable. To avoid this, run a separate (thicker) ground cable from the power supply in addition to the controller ground wire and tie the grounds together at the strip. This will prevent ground current from passing through the controller's ground wire, keeping the grounds at the same voltage. If physical separation isn't possible, differential signaling should be used at long distances or high currents to electrically separate ground and signal currents.
Parts
12| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3 |
| 2 | Screw_Terminal_01x03 | footprints:CUI_TB004-508-03BE | J1, J2 |
| 1 | 33 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 3386P-1-101TLF | footprints:TRIM_3386P-1-101TLF | VR1 |
| 1 | 500pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 74AHCT1G125 | Package_TO_SOT_SMD:TSOT-23-5_HandSoldering | U3 |
| 1 | NCP730ASN500T1G | footprints:DBV0005A_M | U1 |
| 1 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | ~ | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
Similar boards
- 4 layers241.2 × 327.2 mm

- 2 layers40 × 18.5 mm

- 2 layers40.1 × 49.3 mm

Big Honking Button
wntrblm/Big_Honking_Button
A simple Eurorack sampler and performance module in a silly package.
54 parts60 - 2 layers68 × 100 mm

Keyboard featherwing
arturo182/keyboard_featherwing_hw
The Keyboard FeatherWing is an easy way to add a handheld Qwerty keyboard and a 2.6” color display (+ more) to your project! It fits well in your hands and is great for typing with your thumbs, early 2000s-style.
58 parts43 - 2 layers53 × 53 mm

Keypad
realworldpixel/home-assistant-keypad
A 9-key macro keypad for Home Assistant, running ESPHome. Every key is RGB backlit, and comes in two variants: one that sits on a desk and one that mounts on a wall, with magnets or screws.
36 parts29 - 2 layers45.5 × 26.2 mm

P1-wifi gateway22v4jlc
romix123/P1-wifi-gateway
Deze software brengt verschillende componenten bij elkaar in een handzaam pakket.
27 parts27 - 2 layers65 × 85 mm

- 2 layers

Questions
How big is the Levelshift tunable ahct PCB?
It measures 71.8 × 25.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Levelshift tunable ahct use?
12 parts, built around the 74AHCT1G125SE and 3386P-1-101TLF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Levelshift tunable ahct KiCad files?
From the saratoga4/levelshift_tunable_ahct repository on GitHub, at the commit this page was made from: the board is levelshift_tunable_ahct.kicad_pcb and its schematic .history/levelshift_tunable_ahct.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Levelshift tunable ahct design in my own project?
Its repository states no licence, so its author keeps all rights: ask saratoga4 before reusing the design.