Skip to the content
2 layers69 × 73 mmLed potencia, the printed circuit board in 3D

multiplexacion de transistores por medio de un 74hc695 (SIPO)

Size
69 × 73 mm
Copper layers
2
Thickness
1.6 mm
Parts
44
Nets
31
Pads
108
Tracks, vias
182, 0
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
10 Jun 2026
Updated
2 Oct 2026

Overview

Led potencia is an open-source printed circuit board by santitfg, from the santitfg/proyectores_led_5w repository on GitHub. It is a 2-layer board of 69 × 73 mm with 44 parts on 31 nets, routed with 182 tracks and 0 vias.

It is built around the 74HC595 and IRLZ44N. Its parts include 16 resistors, 14 connectors, 8 transistors and 1 IC.

Main components

2

README

README.md

redo

en el 74hc595 el pin 10 (rst ) si o si a vcc y el pin 13 output enable va a gng si o si

Conector 1 — entrada de datos serie (SER)

Chip: 74HC595 (registro de desplazamiento serie-in / paralelo-out). Molex 5 pines.

PinColorSeñalGPIO ESP32GPIO ESP32-S3Descripción
1⚫ NegroGND——Tierra
2⚪ BlancoSRCLK / CPgpio23gpio18Shift Clock (SH_CP, pin 11) / SPI2 SCLK
3🟢 VerdeRCLK / PLgpio22gpio10Register Clock / Latch (ST_CP, pin 12)
4🩶 GrisSER / DSgpio2gpio4Serial data in (DS, pin 14) / SPI2 MOSI
5🔴 RojoVCC——Alimentación

Conector 2 — salida en cascada (Q7)

Conector para encadenar el SER (pin 14) del siguiente 74HC595 a la salida en cascada Q7' (pin 9) de este.

PinColorSeñalGPIO ESP32GPIO ESP32-S3Descripción
1⚫ NegroGND——Tierra
2⚪ BlancoSRCLK / CPgpio23gpio18Shift Clock (SH_CP, pin 11) / SPI2 SCLK
3🟢 VerdeRCLK / PLgpio22gpio10Register Clock / Latch (ST_CP, pin 12)
4🩶 GrisQ7gpio35gpio5Salida en cascada (Q7', pin 9) hacia el SER del siguiente 74HC595
5🔴 RojoVCC——Alimentación

estoy controlando con el 74hc595 la matriz desde las siguientes filas y columnas: Q0 ... Q3 se conectan a los 2n2222 controlanto el gate de IRF9630 Q4 ... Q7 se conectan directo al gate IRLZ44N

revision de laburo

PCB

IRF9630 high side y esta a up down en gate IRLZ44N low side y esta a pull down en gate

————

revision en protoboard 5v y señales activas de irlz44n y 2n2222 a 3.3: IRLZ44N gate ( pin 1) 10k a pull Down 1k a señal (vcc activa el paso de corriente) drain ( pin 2) a gnd-terminal source (pin 3) a GND

IRF9630 gate ( pin 1) 10k a pull up 1k a señal (gnd activa el paso de corriente)(2n2222) drain ( pin 2) a Vout-terminal source (pin 3) a VIN

2n2222 ( funcionamiento real es emisor a gnd y colector lado vcc) emisor (pin 1) a GND base (pin 2) señal ic ( via 1k Resi) colector (pin 3) ( señal hacia irf9630 via 1k resi) vcc activa el paso de corriente)x

TODO: arreglar kicad corrigiendo los elementos mencionados (inverti pista VIN x Vout-terminal)

Fallas en el circuito funciona la mitad de puntos en modo damero O X O X X O X O O X O X X O X O

Nomenclar correstamente las columnas y filas pero los v y gnd en los mismos no todos fallan de la misma manera 1: 2: 3: 4:

Filas q0 (pin 15) : IRF9630 1 q1 (pin 1) : IRF9630 2 q2 (pin 2) : IRF9630 3 q3 (pin 3) : IRF9630 4

Columnas q4 (pin 4) : IRLZ44N 1 q5 (pin 5) : IRLZ44N 2 q6 (pin 6) : IRLZ44N 3 q7 (pin 7) : IRLZ44N 4

. q4 q3 q2 q1 q3 4 3 2 1 q2 8 7 6 5 q1 12 11 10 9 q0 16 15 14 13

funciona raro al enviar 0xFF se apagan las salidas y al 0x00 se prenden

Parts

44
QtyValueFootprintReferences
810kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR33, R34, R35, R36, R37, R38, R39, R40
8220Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR9, R10, R11, R12, R13, R14, R15, R16
8Conn_01x02_PinConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ9, J10, J11, J12, J13, J14, J15, J16
8IRLZ44NPackage_TO_SOT_THT:TO-220-3_VerticalQ17, Q18, Q19, Q20, Q21, Q22, Q23, Q24
4Conn_01x02_SocketConnector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_VerticalJ3, J17, J18, J19
4MountingHoleMountingHole:MountingHole_2.2mm_M2_DIN965_PadH1, H2, H3, H4
2Conn_01x03_PinConnector_Molex:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_VerticalJ1, J2
10Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontalpuente1
174HC595Package_DIP:DIP-16_W7.62mm_Socket_LongPadsU1

Similar boards

  • 2 layers99.1 × 99.1 mmFlipDotDriver, the printed circuit board in 3D

    FlipDotDriver

    bitluni/FlippyFlip

    49 parts14
  • 4 layers71.3 × 95.9 mmChessBotController, the printed circuit board in 3D

    ChessBotController

    cryptoAlgorithm/chess-printer

    A chess bot, but on steroids. Custom 3D printer control board with a few oddly specific features.

    55 parts3
  • 2 layersOrgan Serial to Parallel, the printed circuit board in 3D

    Organ Serial to Parallel

    locokepler/Pipe_Organ

    The repository of the pipe organ, over the different iterations of mechanical, electrical, and code design

    105 parts2
  • 2 layers163.5 × 55 mmIROC U Charging NMOS, the printed circuit board in 3D

    IROC U Charging NMOS

    24bec124-sketch/IROC-U-Charging-NMOS

    Developed for Team Arrow as part of IRoC-U (ISRO Robotics Challenge - URSC), a national student competition hosted by the Indian Space Research Organization (ISRO).

    41 parts1MIT
  • 2 layers103.1 × 77 mmPCB layout, the printed circuit board in 3D

    PCB layout

    Abdulsalam-Alsheikh/CircleOfLuck

    This project was developed to provide an efficient and engaging way to randomly select winners in competitions or events where the order of winners needs to be determined fairly and without bias.

    59 parts
  • 2 layers163.8 × 52.4 mmSolenoid driver v2, the printed circuit board in 3D

    Solenoid driver v2

    jboymel/piano-robot

    Modular solenoid-based robotic piano actuator system — Northwestern SURG 2026

    75 parts
  • 2 layers91.8 × 42.7 mmRacktemperatur, the printed circuit board in 3D

    Racktemperatur

    klein0r/pcb-rack-temperature-control

    Control fans in your rack depending on current temperature

    28 partsMIT

Questions

How big is the Led potencia PCB?

It measures 69 × 73 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Led potencia use?

44 parts, built around the 74HC595 and IRLZ44N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Led potencia KiCad files?

From the santitfg/proyectores_led_5w repository on GitHub, at the commit this page was made from: the board is circuitos/led_potencia/led_potencia.kicad_pcb and its schematic circuitos/led_potencia/led_potencia.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Led potencia design in my own project?

Its repository states no licence, so its author keeps all rights: ask santitfg before reusing the design.