
Ultra DB X51 v1
ExploreEmbedded/8051_DevelopmentBoard
Design files and sample code for 8051 development Ultra Boards

This is Project 3 of my #50BoardChallenge. This is a 2-channel H-Bridge motor driver board, designed to control the speed and direction of two DC motors.
MOTOR DRIVER is an open-source printed circuit board by SANJITHKUMAR-EMBEDDED, from the SANJITHKUMAR-EMBEDDED/L293D-Motor-Driver repository on GitHub. It is a 2-layer board of 35 × 44 mm with 14 parts on 13 nets, routed with 74 tracks and 5 vias.
It is built around the L293D. Its parts include 6 connectors, 3 capacitors and 1 IC. It belongs with the robots and motor control boards of this library.
This is Project 3 of my #50BoardChallenge. This is a 2-channel H-Bridge motor driver board, designed to control the speed and direction of two DC motors.
This project was a major step up in complexity, focusing on power management and heatsinking.
+V (Motor) supply and a VCC (Logic) supply.This board was designed to handle high currents and manage heat:
GND pins to act as a heatsink and pull heat away from the chip.MOTOR_POWER (60 mil): For all high-current motor and +V traces.LOGIC_POWER (20 mil): For the VCC and logic GND traces.Default (8 mil): For all low-current logic signals (IN1-4, EN1-2).GND Plane: Used a solid copper pour on the bottom layer for a stable, low-noise ground reference.| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | Screw_Terminal_01x02 | 1729128:PHOENIX_1729128 | J2, J5, J6 |
| 2 | 0.1uF | Capacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mm | C1, C3 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3, J4 |
| 1 | 220uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C2 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | L293D | Package_DIP:DIP-16_W7.62mm | U1 |
The 10 most common of 14 parts.

ExploreEmbedded/8051_DevelopmentBoard
Design files and sample code for 8051 development Ultra Boards

NikodemBartnik/Small-Projects
All of smaller projects (Arduino, PCBs, electronics, code)

geno543/Redropi_highway
the project aims to detect asteroids and meteor movement using high-quality cameras and radar detection methods using an AI model for accurate analysis, and it classifies bodies be in three categories: non-meteor…


harrislab-brown/DropGen
DropGen uses a fluid reservoir and a piezoelectric buzzer to precisely and repeatably dispense small droplets on demand.



It measures 35 × 44 mm and has 2 copper layers, 1.6 mm thick.
14 parts, built around the L293D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the SANJITHKUMAR-EMBEDDED/L293D-Motor-Driver repository on GitHub, at the commit this page was made from: the board is MOTOR_DRIVER.kicad_pcb and its schematic MOTOR_DRIVER.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask SANJITHKUMAR-EMBEDDED before reusing the design.