

Gripper hatt
some of my creations
- Size
- 65 × 56 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 20
- Nets
- 53
- Pads
- 115
- Tracks, vias
- 282, 2
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 6 Jun 2025
- Updated
- 8 Jun 2025
Overview
Gripper hatt is an open-source printed circuit board by sami-klibi, from the sami-klibi/PCBs repository on GitHub. It is a 2-layer board of 65 × 56 mm with 20 parts on 53 nets, routed with 282 tracks and 2 vias.
It is built around the TMC2209SILENTSTEPSTICK. Its parts include 2 ICs, 2 diodes, 2 connectors and 1 resistor.
Main components
1README
ESP32_Shield/README.mda custom shield designed for the ESP32, aimed at centralizing and simplifying the control of various system components. This board integrates several essential elements:
🧠 A dedicated slot for the ESP32, ensuring a clean and stable integration of the microcontroller.
🔄 A TMC2209 stepper motor driver, used for quiet and precise motor control.
🔋 An LM2596 voltage regulator, selected with the help of the datasheet [5], to provide a stable power supply to the system.
🔔 An integrated buzzer for simple audible alerts.
💡 Status indicator LEDs, to visually monitor the state and operation of the system.The shield also includes several connection ports:
⛓️ A port for a limit switch used for homing and position detection.
🔗 An I2C communication port for connecting servo motor driver boards (e.g., PCA9685).
🔌 A port for the stepper motor connection.
🌬️ A port for a cooling fan, ensuring efficient thermal management.This shield provides a centralized, compact, and efficient management solution for the system’s hardware, reducing wiring complexity and improving physical integration within the enclosure.
Schematic Diagram
Routing

3D View

Parts
20| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_2.7mm_M2.5 | MountingHole:MountingHole_2.7mm_M2.5 | MH1, MH2, MH3, MH4 |
| 2 | TMC2209_SILENTSTEPSTICK | TMC2209:MODULE_TMC2209_SILENTSTEPSTICK | U2, U3 |
| 1 | 1N5819 | Diode_SMD:D_SOD-123 | D2 |
| 1 | 470Ω | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | Barrel_Jack | Connector_BarrelJack:BarrelJack_Horizontal | J2 |
| 1 | FAN | Connector_PinHeader_1.00mm:PinHeader_1x02_P1.00mm_Vertical | FAN |
| 1 | GPIO | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | GR_SERVO | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | GR_SERVO |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
| 1 | LOGO | logos:asqii.logo | G*** |
| 1 | STEPPER_X | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | STEPPER_X |
| 1 | STEPPER_Y | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | STEPPER_Y |
| 1 | X_SWITCH | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | X_SWITCH |
| 1 | Y_SWITCH | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | Y_SWITCH |
| 1 | Z_SERVO | Connector_JST:JST_XH_B3B-XH-AM_1x03_P2.50mm_Vertical | Z_SERVO |
| 1 | Z_SWITCH | Connector_PinHeader_1.00mm:PinHeader_1x03_P1.00mm_Vertical | Z_SWITCH |
More from sami-klibi/PCBs
3- 2 layers165.3 × 115.1 mm

- 2 layers119.9 × 58 mm

- 2 layers73.5 × 71.5 mm

Similar boards
- 2 layers90.8 × 35.6 mm

ERCF easy brd
Tircown/ERCF-easy-brd
More informations on how to reset for flashing:\ https://wiki.seeedstudio.com/Seeeduino-XIAO/#enter-bootloader-mode
28 parts195GPL-3.0 - 2 layers113.4 × 55.3 mm

- 2 layers92.5 × 62.5 mm

DropGenPCB
harrislab-brown/DropGen
DropGen uses a fluid reservoir and a piezoelectric buzzer to precisely and repeatably dispense small droplets on demand.
25 parts12CC-BY-SA-4.0 - 4 layers130.5 × 171 mm

UniMixBase
jarekkt/UniController
This is a off-spin from my commercial controller for industrial ink printers. It is designed for pick & place machines controlled by OpenPnp
157 parts6 - 2 layers91.6 × 65 mm

- 2 layers185.7 × 101.9 mm

- 4 layers102 × 102 mm

Controller
Angelo13C/3d-printer
Firmware, electronics, mechanics and control interface of a 3D printer
97 parts2 - 2 layers24.5 × 49.4 mm

Roller blind controller
ItsRebaseTime/turbomansion
Hello, welcome to the turbomansion repository.
6 parts2Unlicense
Questions
How big is the Gripper hatt PCB?
It measures 65 × 56 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Gripper hatt use?
20 parts, built around the TMC2209SILENTSTEPSTICK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gripper hatt KiCad files?
From the sami-klibi/PCBs repository on GitHub, at the commit this page was made from: the board is PI_hat/Gripper_hatt/Gripper_hatt.kicad_pcb and its schematic ESP32_Shield/esp32_driver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gripper hatt design in my own project?
Its repository states no licence, so its author keeps all rights: ask sami-klibi before reusing the design.