
Back pcb
ZeroPhone/ZeroPhone-PCBs
PCB files for ZeroPhone - for gerbers and schematics, go to "Releases" tab!

Main circuit board design for disinfected robot project.
All In One is an open-source printed circuit board by sajukhakurel074, from the sajukhakurel074/Disinfecting_Robot_PCB repository on GitHub. It is a 2-layer board of 257.1 × 139.3 mm with 158 parts on 162 nets, routed with 1,544 tracks and 9 vias.
It is built around the LM339 and BC547. Its parts include 58 resistors, 20 ICs, 18 diodes, 13 capacitors and 11 connectors. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Main circuit board design for disinfecting Robot Project.
This project was funded by Nepal Academy of Science and Technology (NAST) during the Covid-19 pandemic. The main aim of this project was to use a remotely comtrolled robot that would spary the disinfecting solution in the infected areas.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 1K | modFiles:Resistor_small | R24, R26, R28, R29, R30, R31, R32, R33, R34, R36, R37, R44, R55 |
| 13 | 220 | modFiles:Resistor_small | R8, R9, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R59 |
| 12 | PC817 | Package_DIP:DIP-4_W7.62mm | U5, U6, U7, U8, U9, U10, U11, U12, U13, U15, U16, U17 |
| 11 | C | modFiles:Capacitor_Disc_Small | C2, C3, C4, C5, C6, C7, C13, C25, C27, C33, C36 |
| 10 | R | modFiles:Resistor_small | 1K12, R4, R6, R23, R27, R38, R39, R40, R66, R74 |
| 10 | RED | modFiles:LED_D3.0mm | D2, D4, D5, D6, D8, D9, D11, D13, D15, D16 |
| 9 | 470 | modFiles:Resistor_small | R7, R43, R45, R47, R57, R58, R71, R72, R73 |
| 7 | 4.7k | modFiles:Resistor_small | eR70, R41, R42, R56, R60, R64, R65 |
| 7 | BC547 | modFiles:BC547 | Q1, Q2, Q3, Q4, Q5, Q6, Q7 |
| 5 | CP1 | modFiles:Capacitor_1000uF | 1000uf, C1, C8, C9, C41 |
| 4 | 10K | modFiles:Resistor_small | R53, R54, R67, R68 |
| 3 | DIODE | modFiles:Diode_Medium | D1, D3, D10 |
| 3 | D_Zener | Diode_THT:D_T-1_P5.08mm_Horizontal | D7, D12, D14 |
| 2 | 100 | modFiles:Resistor_small | R49, R62 |
| 2 | 104 | modFiles:Capacitor_Disc_Small | C37, C38 |
| 2 | 2.2k | modFiles:Resistor_small | R35, R69 |
| 2 | 3.3k | modFiles:Resistor_small | R3, R5 |
| 2 | 3.9K | modFiles:Resistor_small | R46, R52 |
| 2 | 47 | modFiles:Resistor_small | R50, R61 |
| 2 | 4k7 | modFiles:Resistor_small | R21, R25 |
| 2 | 5V_Regulator | modFiles:Buck_5A | U4, U20 |
| 2 | CP1 | modFiles:Capacitor_10uF | 10uf, C39 |
| 2 | Conn_01x01_Female | Connector_PinHeader_2.00mm:PinHeader_1x01_P2.00mm_Vertical | J13, J13 |
| 2 | Fuse | modFiles:Fuse_Holder | F1, F2 |
| 2 | L298 | 0_18:saju_____L298 | U2, U3 |
| 2 | LM339 | Package_DIP:DIP-14_W7.62mm_LongPads | U18, U19 |
| 1 | 1.5k | modFiles:Resistor_small | R1 |
| 1 | 10k | modFiles:Resistor_small | R2 |
| 1 | 12V_Supply | modFiles:Solar_Connector | d1 |
| 1 | 1k | modFiles:Resistor_small | R63 |
| 1 | 1k1 | modFiles:Resistor_small | R20 |
| 1 | 24V_Supply | modFiles:Solar_Connector | d2 |
| 1 | 33 | modFiles:Resistor_small | R51 |
| 1 | 5V_Regulator | modFiles:Buck_Regulator | U14 |
| 1 | 68 | modFiles:Resistor_small | R48 |
| 1 | 680 | modFiles:Resistor_small | R22 |
| 1 | 6V_Relay | modFiles:Relay_6V | Rly1 |
| 1 | ARM PROXY | 0_18:New_conn_1x4 | J8 |
| 1 | Base_Proxy | 0_18:New_conn_1x4 | J3 |
| 1 | Fan | 0_18:New_conn_1x2 | J11 |
| 1 | MS_jumper | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | GND |
| 1 | MS_jumper_xaxis | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | 5V |
| 1 | MS_jumper_yaxis | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | MS1 |
| 1 | Motors | 0_18:New_conn_1x8 | J10 |
| 1 | Prashant_library_Arduino_Mega2560_Shield | modFiles:Arduino_Mega2560_Shield | U1 |
| 1 | Raspberry_pi | 0_18:New_conn_1x2 | J12 |
| 1 | Stepper_xaxis | 0_18:New_conn_1x4 | J6 |
| 1 | Water_Pump | 0_18:New_conn_1x2 | J4 |
| 1 | X_AXIS | modFiles:A4998 | A1 |
| 1 | bluetooth | 0_18:bluetooth | J9 |
| 1 | servo_motor | 0_18:New_conn_1x4 | J7 |

ZeroPhone/ZeroPhone-PCBs
PCB files for ZeroPhone - for gerbers and schematics, go to "Releases" tab!

MadsRudolph/vinyl-adc
Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

aiabusalama/pumpbox
REISBOT Pump Guard: a Rust + Raspberry Pi box that keeps a 150 V solar water pump alive

Avyukth-ma/Electronics-Projects
Collection of electronics, embedded systems, and PCB design projects

AgustinPrietoValdez/competition-robots
Custom competition robots — maze/micromouse (MISA), sumo (TATAMI 1) & mini-sumo (RUCHO). KiCad PCBs, STM32/Arduino firmware, Fusion 360. National champion & international prizes — by EDNAROBOTICS.

Neumi/open_echo
Open Source echo sounder / depth sounder / SONAR for bathymetry and research. Arduino based and compatible.


giant-axon/lu.i-neuron-pcb
Lu.i is an electronic neuron circuit mimicking and illustrating the basic dynamics of real, biological neurons. The printed circuit board (PCB) features a configurable, fully analog implementation of the leaky…
It measures 257.1 × 139.3 mm and has 2 copper layers, 1.6 mm thick.
158 parts, built around the LM339 and BC547. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the sajukhakurel074/Disinfecting_Robot_PCB repository on GitHub, at the commit this page was made from: the board is All_In_One.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask sajukhakurel074 before reusing the design.