
Vik universal
sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.
Vik playground is an open-source printed circuit board by sadekbaroudi, from the sadekbaroudi/vik repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 2-layer board of 99 × 65.5 mm with 40 parts on 71 nets, routed with 800 tracks and 168 vias.
It is built around the MCP23017-E/SO, SN74HC595D and TS3A27518EPW, with the 1N4148W and WS2812B among its other parts. Its parts include 10 diodes, 8 connectors, 7 switches, 4 resistors and 3 capacitors.
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.
This was used to demonstrate a build for vulpes minora. See the repo for pictures.
For PCB fabrication, you can use the files in the production folder.
Using the 3 files above, this has been tested at jlcpcb.com
| Category | Classification | Response |
|---|---|---|
| FPC connector | Required | :heavy_check_mark: |
| Breakout pins | Recommended | :x: |
| Uses: SPI | Optional | :heavy_check_mark: |
| SPI used for SPI only | Strongly recommended | :heavy_check_mark: |
| Uses: I2C | Optional | :x: |
| I2C used for I2C only | Strongly Recommended | N/A |
| I2C pull ups | Required | N/A |
| Uses: RGB | Optional | :heavy_check_mark: |
| Uses: Extra GPIO 1 | Optional | :heavy_check_mark: |
| Uses: Extra GPIO 2 | Optional | :heavy_check_mark: |
| Standard PCB Size/Mount | Strongly recommended | Large |


| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | Conn_01x08_Socket | fingerpunch:PinSocket_1x08_P2.54mm_Vertical | J2, J3, J4, J5, J6, J7, J17 |
| 6 | 1N4148W | Diode_SMD:D_SOD-123 | D1, D2, D3, D4, D5, D6 |
| 6 | SW_Push | fingerpunch:gateron-ks27-choc-v1-mx-soldered-and-hotswap | SW1, SW2, SW3, SW4, SW5, SW6 |
| 4 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D100, D101, D102, D103 |
| 3 | Jumper_2_Bridged | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | JP7, JP8, JP9 |
| 2 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3 |
| 2 | 4.7kΩ | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R9 |
| 1 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10kΩ | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | MCP23017-E/SO | Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm | U2 |
| 1 | RotaryEncoder_Switch | fingerpunch:RotaryEncoder_EC11-no-legs | SW10 |
| 1 | Row Col Matrix | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | JP10 |
| 1 | SN74HC595 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP1 |
| 1 | TS3A27518EPW | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U3 |
| 1 | ~ | vik:vik-module-connector-horizontal | J1 |

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

sadekbaroudi/vik
This is a VIK module designed to mount a PER56 scroll ring, with a 35mm Cirque Trackpad and optional WS2812B LEDs.

Mykola2/uart-cable-tester
design.py is the single source of truth: parts, footprints, pin-to-net map and positions. Everything else is generated from it.



pierrechevalier83/ferris
A low profile split keyboard designed to satisfy one single use case elegantly


hdh7485/agent-deck
Physical AI agent controller for Codex, Hermes, OMX, and tmux workflows

kuvychko/nanovolt-divider
Programmable 1e-5/1e-6/1e-7 precision attenuator for nanovolt metrology: KiCad, ESP32 firmware, calibration method and results

thanoslabs/keyboards
Schematics, pcbs, layout files for all my keyboard projects
It measures 99 × 65.5 mm and has 2 copper layers, 1.6 mm thick.
40 parts, built around the MCP23017-E/SO, SN74HC595D, TS3A27518EPW and 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the sadekbaroudi/vik repository on GitHub, at the commit this page was made from: the board is pcb/vik-playground/vik-playground.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).