

MIG Dumper
MIG Dumper and Flashcart PCB files in KiCad
- Size
- 60 × 33 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 73
- Nets
- 107
- Pads
- 375
- Tracks, vias
- 753, 121
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 18 Oct 2024
- Updated
- 16 Jul 2025
Overview
MIG Dumper is an open-source printed circuit board by sabogalc, from the sabogalc/MIG-Flash-PCBs repository on GitHub, published under the WTFPL licence. It is a 4-layer board of 60 × 33 mm with 73 parts on 107 nets, routed with 753 tracks and 121 vias.
It is built around the ICE40UP5K-SG48ITR50, ESP32-S2 and GL823K-HCY04, with the MAX20022ATIA+, LQM21PN1R5MEHD and APT3216LSECK/J3-PRV among its other parts. Its parts include 45 capacitors, 13 resistors, 4 ICs, 4 inductors and 3 connectors. It belongs with the ESP32 and FPGA and CPLD boards of this library.
Main components
7ICE40UP5K-SG48ITR50
QFN-48QFN-48 Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)ESP32-S2
QFN-56-EP(7x7)-40℃~+125℃ -97dBm 135mA 150Mbps 2.4GHz 2.4GHz~2.4835GHz 2.8V~3.6V 63mA DMA function SPI、UART、I2C、I2S WiFi transceiver QFN-56-EP(7x7) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICsGL823K-HCY04
SSOP-16-150mil0℃~+70℃ 300uA 4.75V~5.25V 480Mbps 50mA USB 2.0 USB to SD SSOP-16-150mil USB Converters ROHSGenesys LogicUSB ConvertersMAX20022ATIA+
TQFN-28-EP(5x5)EMI optimization (spread spectrum)、Overcurrent Protection、Frequency synchronization、Operating status indication、Adjustable current limiting、Cycle-by-cycle current limiting TQFN-28-EP(5x5) DC-DC Converters ROHSMaxim Integrated (Analog Devices)DC-DC ConvertersLQM21PN1R5MEHD
08051.5uH 100mΩ 40MHz 550mA 550mA ±20% 0805 Inductors (SMD) ROHSMurataInductors (SMD)APT3216LSECK/J3-PRV
1206-40℃~+85℃ 1.8V 140° 2mA 40mcd 625nm 640nm Red Water Clear 1206 LED Indication - Discrete ROHSKingbrightLED Indication - DiscreteECS-400-10-37B2-CKY-TR
SMD2016-4P-30℃~+85℃ 10pF 40MHz 40Ω Crystal Oscillator ±10ppm ±10ppm SMD2016-4P Crystals ROHSECSCrystals
README
KiCad Projects/MIG Flashcart/README.mdMIG Flashcart
Overview
The Flashcart board is very compact, and it is a bit challenging to solder it by hand. Most of the passive components are the 0201 size, and the 0404 RGB LED in the top right is also extremely small. Additionally, the vias have been trimmed down to a 0.2mm size to accommodate the board's routing.
A series of leaks in July 2021 made the low-level hardware of the Switch game cartridge reader public, and it is powered by an ASIC called Lotus3. I don't know much about how this chip/protocol works, but the FPGA and microcontroller in this flashcart are programmed to communicate on this custom interface.
Ordering Specifications
To ensure this board fits in the game enclosure and that it can be read, it should be ordered as a 0.8mm thick board with an ENIG finish. All other options can be left as their default.
Component Measurements and BOM Discrepancies
I measured the components to the best of my ability, but there may be slight discrepancies. For example, I found it odd that 12 of the capacitors measured as 0.82uF and 4 of them measured as 0.88uF. I suspect that all of them are 0.82uF, and imperfections in the measurements caused the 4 outliers to read higher values. Even so, they were consistently measuring high enough that I felt it best to mark them as 0.88uF in the schematic. This point is a bit moot, however, because I could not find any 0201 capacitors on either Digikey or Mouser for 0.82uF or 0.88uF. As such, the BOMs have some substitutions, such as 1uF capacitors in place of the 0.82uF and 0.88uF ones, but the measurements in the schematic and PCB are what most align with what I measured in real life.
Can I use these designs to manufacture my own MIG Flashcart?
The answer is the same as in the corresponding section of the Dumper's README. Due to the firmware encryption on the original boards, making this board from scratch (e.g. without transplanting the original μC and FPGA) proves to be a bit of a challenge.
Importantly though, the programmer board schematic I made for the Dumper will not work for the Flashcart as-is since the Flashcart has no 5V/VBUS signal. The programmer board would need to be modified to have an onboard 3.3V regulator, and then with this signal on the Flashcart's VCC breakout signal, it should work. Should anyone make that programmer board and want to write their own firmware, the instructions for accomplishing this can be found on Espressif's website in the bootloader mode note.
I have assembled this board with parts from the included BOM and confirmed that it works when using the chips from an OEM MIG Flashcart. If you are using the parts from the BOM, the LED has a pin 1 indicator which I will show in a photo below. Make sure that the white squre between the two gold pins is facing into the board towards the crystal oscillator.
Below are some photos of the board from this repository in the flashcart enclosure.
The cartridge reading a game in the Switch and showing a green status LED.
KiCad 3D View
Below are screenshots of the board from KiCad's 3D board viewer.
Parts
73| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 1u | Capacitor_SMD:C_0603_1608Metric | C9, C11, C12, C13, C14, C16, C20, C21, C28, C37 |
| 7 | 110n | Capacitor_SMD:C_0603_1608Metric | C8, C10, C15, C17, C18, C19, C34 |
| 6 | 2u2 | Capacitor_SMD:C_0603_1608Metric | C22, C23, C30, C31, C32, C33 |
| 5 | DNP | Capacitor_SMD:C_0603_1608Metric | C2, C40, C41, C42, C43 |
| 4 | 10u | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C5, C24, C35, C38 |
| 4 | LQM21PN1R5MEHD | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1, L2, L3, L4 |
| 3 | 24k3 | Resistor_SMD:R_0603_1608Metric | R2, R3, R12 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R10 |
| 2 | 10p | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | 15p | Capacitor_SMD:C_0603_1608Metric | C26, C36 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R4, R7 |
| 2 | 8u2 | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C6, C25 |
| 2 | DNP | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C7 |
| 2 | DNP | Capacitor_SMD:C_0201_0603Metric | C44, C45 |
| 2 | MountingHole | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad_TopBottom | H1, H2 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R13 |
| 1 | 19k6 | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 19p | Capacitor_SMD:C_0603_1608Metric | C27 |
| 1 | 20k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 330R | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 36k5 | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 4u5 | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C29 |
| 1 | 56k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 75p | Capacitor_SMD:C_0603_1608Metric | C39 |
| 1 | APT3216LSECK/J3-PRV | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | Conn_01x17_MountingPin | MIG Dumper:Switch_Cartridge | J3 |
| 1 | Conn_02x04_Counter_Clockwise | Connector_PinHeader_1.27mm:PinHeader_2x04_P1.27mm_Vertical | J2 |
| 1 | ECS-400-10-37B2-CKY-TR | Crystal:Crystal_SMD_SeikoEpson_FA128-4Pin_2.0x1.6mm | Y1 |
| 1 | ESP32-S2 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U1 |
| 1 | GL823K-HCY04 | Package_SO:SSOP-16_3.9x4.9mm_P0.635mm | U3 |
| 1 | ICE40UP5K-SG48ITR | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm | U2 |
| 1 | MAX20022ATIA+ | Package_DFN_QFN:TQFN-28-1EP_5x5mm_P0.5mm_EP2.7x2.7mm | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
More from sabogalc/MIG-Flash-PCBs
1- 4 layers27.4 × 17 mm

Similar boards
- 4 layers57 × 33 mm

Sensor pcb
nichlock/open-linear-scale
Open-source capacitive linear encoder / DIY DRO scale: KiCad PCBs, STM32 firmware, and test data. Same principle as digital calipers.
69 parts73 - 6 layers567.7 × 328.4 mm

- 2 layers54.8 × 56.7 mm

GC Nano Top
CrazyGadgetMods/GC-Nano-Suite
Collection of custom PCBs / BOM used for the GC Nano
35 parts14 - 4 layers115 × 82.3 mm

MainPCB
HelloAlex4/Maturitaetsarbeit-Design-and-Development-of-a-Portable-Stereoscopic-Wigglegram-Camera
Documentation of the merged wigglegram camera
288 parts12 - 6 layers131.5 × 132.4 mm

BedCooler
NicholasKorth/BedCooler
A dual-zone heating and cooling controller for a bed: a 6-layer KiCad board with an STM32G474 real-time controller and a Raspberry Pi Compute Module 5 host.
258 parts11 - 2 layers31 × 68.4 mm

- 4 layers31 × 68.4 mm

Thinkmoth nvme m2-basic
mothenjoyer69/thinkmoth-expresscard
A low cost, open source ExpressCard 34/54 adapter with M.2 2230 and 2242 support
22 parts7CERN-OHL-S-2.0 - 4 layers80 × 55 mm

Questions
How big is the MIG Dumper PCB?
It measures 60 × 33 mm and has 4 copper layers, 1.6 mm thick.
What parts does the MIG Dumper use?
73 parts, built around the ICE40UP5K-SG48ITR50, ESP32-S2, GL823K-HCY04 and MAX20022ATIA+. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the MIG Dumper KiCad files?
From the sabogalc/MIG-Flash-PCBs repository on GitHub, at the commit this page was made from: the board is KiCad Projects/MIG Dumper/MIG Dumper.kicad_pcb and its schematic KiCad Projects/MIG Dumper/Capacitors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the MIG Dumper design in my own project?
Its repository publishes it under the WTFPL licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).