
ElectromagnetController V5
brooklynresearch/FerrousControl
Ferrofluid controlled through an electromagnetic array

LEDBoard 4x2; pixel pitch: 20mm x 5mm; LED: Rohm MSL0402RGBU1; Driver: TLC5971
LEDBoard 4x2 p20x5 is an open-source printed circuit board by s-light, from the s-light/LEDBoard_4x2_p20x5 repository on GitHub, published under the MIT licence. It is a 2-layer board of 64 × 9 mm with 20 parts on 35 nets, routed with 380 tracks and 34 vias.
It is built around the TLC5971PWP. Its parts include 4 capacitors, 3 connectors, 2 resistors and 2 ICs.
compatible to LEDBoard_4x6_p20x5
WIP
there are groups of 4 LEDs that are controlled by one TLC5971.
every controller chip has 12 ConstantCurrent outputs.
so every LED is controllable individual.
you need to create a mapping to linearize the order:
TODO: test & check if this table is correct
| 0 | 1 | 2 | 3 | |
|---|---|---|---|---|
| 0 | IC1 LED1 | IC1 LED2 | IC2 LED1 | IC2 LED2 |
| 1 | IC1 LED3 | IC1 LED4 | IC2 LED3 | IC2 LED4 |
const uint8_t channel_position_map[2][4] = {
{ 0, 1, 4, 5},
{ 2, 3, 6, 7},
};for arduino you can use ulrichstern/Tlc59711
for other things have a look at LEDBoard_4x4_16bit
all files in LEDBoard_4x2_p20x5
by
Stefan Krüger (s-light)
are licensed under a
Creative Commons Attribution 4.0 International License
.
all software parts/files are licensed under MIT.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | LED_RGB | LEDs_SMD_NICHIA:LED_RGB_0706_1816Metric_ROHM_ThermalVias | D_0x0, D_0x1, D_1x0, D_1x1, D_2x0, D_2x1, D_3x0, D_3x1 |
| 2 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2, C8 |
| 2 | 10uF 6.3V | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C7 |
| 2 | 2k7 0.1% | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R4 |
| 2 | TLC5971PWP | Package_SO:HTSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP3.4x6.5mm_Mask2.75x3.43mm_ThermalVias | U1, U4 |
| 1 | MH_M3 | MountingHole:MountingHole_3.2mm_M3_ISO7380_Pad | H1 |
| 1 | power | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | signal_in | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | signal_out | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |

brooklynresearch/FerrousControl
Ferrofluid controlled through an electromagnetic array


s-light/LED_Board_PCB
small round PCB with TI TLC5971 12ch 16bit LED-driver and NICHIA NSSM124AT RGB-LED. (original for Lumifluidus Prototyp)

s-light/LEDBoard_1x4_16bit_highdensity
LEDBoard 1x4 High Density - with TLC5971 16Bit LED-Driver

s-light/LEDBoard_4x6_p20x5
LEDBoard 4x6; pixel pitch: 20mm x 5mm; LED: Rohm MSL0402RGBU1; Driver: TLC5971

willplatts/led_controller
LED array PCB for lighting with daisy chain controller


apaleslimghost/synths
schematics, PCBs, designs and code for Pale Slim Ghost Synthesisers hardware
It measures 64 × 9 mm and has 2 copper layers, 1.6 mm thick.
20 parts, built around the TLC5971PWP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the s-light/LEDBoard_4x2_p20x5 repository on GitHub, at the commit this page was made from: the board is LEDBoard_4x2_p20x5.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).