Skip to the content
4 layers57.7 × 27 mmSYZYGY PHY, the printed circuit board in 3D

SYZYGY PHY

rustbox/router

Use ARJM11C7-502-KB-EW2 on mouser Tab up, so would have to be placed on the reverse side of the PCB $3.09 @ 10

Size
57.7 × 27 mm
Copper layers
4
Thickness
1.6 mm
Parts
49
Nets
85
Pads
243
Tracks, vias
960, 95
Pours
6
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
10 Jul 2024
Updated
14 Oct 2024

Overview

SYZYGY PHY is an open-source printed circuit board by rustbox, from the rustbox/router repository on GitHub. It is a 4-layer board of 57.7 × 27 mm with 49 parts on 85 nets, routed with 960 tracks and 95 vias.

It is built around the TXV0106BQBR, GPY111 and ARJM11C7-502-KB-EW2. Its parts include 26 capacitors, 10 resistors, 4 connectors, 3 ICs and 1 diode.

Main components

3

README

gsw141-breakout/README.md

GSW141 Switch Chip Breakout

Different Arrangements of the GSW141 Breakout PCB?

RJ45 Jacks

  • Internal Magnetics | External Magnetics
  • LEDs | No LEDs
  • 1000 (or higher) Base-T
    • I think 1G capable means that there are 4 twisted pairs
  • "Tab Up" | "Tab Down"
    • This means the tab on the cable. When tab is down, the cat-5 pins all in a row point "up", and vise versa when tab is up.
    • The GSW141 chip routes traces best with "tab down"
    • "Tab up" + on the reverse side of the board is equivalent to "tab down"
  • How many ports per part

Internal Magnetics

Use ARJM11C7-502-KB-EW2 on mouser

  • Tab up, so would have to be placed on the reverse side of the PCB
  • $3.09 @ 10

4x 1 unit = $12.36

=====================================================================

Use TMJG26945AENL on mouser, 1x2 port

  • Tab down
  • $11.34 per unit

2x 1 unit = $22.68

=====================================================================

Use TMJG46945AENL on mouser, 1x4 port

  • Tab down
  • $18.84 per unit

External Magnetics

  • Mouser 1149848 4 port RJ45 w/ LEDs, $4.34 each
    • Tab up, so would have to be placed on PCB reverse side
  • Mouser LAN2VSOD48351C2 dual port magnetics chip, ~$2 each

1 @ 4.34 + 2 @ $2 = $8.34

====================================================================

  • Mouser 1149854 2 port RJ45 w/LEDs, $2.78 each
    • Tab up, reverse PCB side
  • Mouser LAN2VSOD48351C2 dual port magnetics chip, ~$2 each

2 @ 2.78 + 2 @ 2 = $9.56

Board Questions

[ ] How should the 1000 Base T diff pairs be terminated into the magnetics?

Board TODO

[x] 4 port RJ45 jack [x] RJ45 LEDs [x] Management Interface * SPI, etc * Pin headers [x] Strapping pins? * 206-125ST on mouser * or DS01C-254-L-09BE [x] GPIO Pins, header [x] RGMII/SGMII over edge connctor [x] RGMII/SGMII header [x] Remove these headers actually [x] Power regulation, 3.3V, 1.1V [x] Power jack (latching) and jack * Mouser T6634ST barrel connector * 5.5 mm (out) x 2.1 mm (in) * Out 0v, inside, pos * Barrel Jack: 694106301002 for above [x] Clock input * ECS-400-12-33B2Q-JES-TR3 on mouser * Clock circuit cap calculation comes from https://blog.adafruit.com/2012/01/24/choosing-the-right-crystal-and-caps-for-your-design/ * CL = C1 * C2 / (C1 + C2) + Cstray * Cstray is ~3 pF * If C1 = C2 = C, and CL = 12 pF for the above crystal * so C = 2(CL - Cstray) => C = 18 pF [x] Power switch, latching * Digikey PB400EEQR1BLK maybe? [x] Reset Button * button TS21-34-035-BK-160-SMT-TR on mouser [ ] Power indicator LEDs [x] GSW Power Startup sequence * RC delay from 3.3 V into 1.1V enable [ ] Make sure trace clearance is okay [ ] Power off? [x] Power Caps on GSW chip [x] Blank R for RESREF and RCAL [ ] Fix the RJ45 / magnetic pinout alignment so routing is easier [ ] Diff Pairs that are off by more than 10s of mm should be length tuned [ ] Empty Footprint for linear regulator(s)? [ ] TI 1G checklist https://www.ti.com/lit/an/snla387/snla387.pdf?ts=1720391456901

Parts

49
QtyValueFootprintReferences
17100nCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1, C2, C3, C4, C5, C6, C7, C8, C10, C11, C12, C13, C17, C18, C19, C20 +1
3MountingHole_PadMountingHole:MountingHole_2.7mm_M2.5_PadH1, H2, H3
210uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC25, C26
216kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR2, R3
220pCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC22, C23
2RLEDResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR6, R9
2TXV0106BQBRlocal:TXV0106BQBRU2, U3
120kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR4
122uCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC24
1330Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1
1333pCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC21
14.7ulocal:Inductor 0806 (2016 metric)L1
15Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR10
1ARJM11C7-502-KB-EW2local:ARJM11C7502KBEW2J1
1CCFG0Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC15
1CCFG1Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC14
1CCFG2Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC16
1Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1Conn_01x11Connector_PinSocket_2.54mm:PinSocket_1x11_P2.54mm_VerticalJ2
1Crystal_GND24Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSolderingY1
1GPY111local:QFN50P700X700X90-49N-DU1
1LEDLED_SMD:LED_0805_2012MetricD1
1QTH-020-01-X-D-DP-Alocal:SAMTEC_QTH-020-01-X-D-DP-AJ4
1RCFG0Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR7
1RCFG1Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR5
1RCFG2Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR8

More from rustbox/router

3
  • 4 layers87.1 × 96 mmGsw141-breakout, the printed circuit board in 3D

    Gsw141-breakout

    rustbox/router

    Use ARJM11C7-502-KB-EW2 on mouser Tab up, so would have to be placed on the reverse side of the PCB $3.09 @ 10

    119 parts
  • 2 layers40.5 × 51.7 mmSYZYGY breakout, the printed circuit board in 3D

    SYZYGY breakout

    rustbox/router

    Use ARJM11C7-502-KB-EW2 on mouser Tab up, so would have to be placed on the reverse side of the PCB $3.09 @ 10

    12 parts
  • 4 layers27.6 × 28.4 mmSYZYGY RGMII tester, the printed circuit board in 3D

    SYZYGY RGMII tester

    rustbox/router

    Use ARJM11C7-502-KB-EW2 on mouser Tab up, so would have to be placed on the reverse side of the PCB $3.09 @ 10

    6 parts

Similar boards

  • 2 layers52 × 90 mmEmu brd, the printed circuit board in 3D

    Emu brd

    rscott2049/DECstation2040

    A RP2040 based DECstation emulator

    86 parts212BSD-3-Clause
  • 4 layers110 × 40.7 mmDrone V2 Remote, the printed circuit board in 3D

    Drone V2 Remote

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    49 parts915
  • 4 layers44.5 × 82.6 mmCONTROLLER AMPCD DDI, the printed circuit board in 3D

    CONTROLLER AMPCD DDI

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    49 parts431
  • 4 layers41 × 35 mmDiffprobe prototype, the printed circuit board in 3D

    Diffprobe prototype

    azonenberg/starshipraider

    Open hardware test equipment

    49 parts193BSD-3-Clause
  • 4 layers80 × 73.8 mmESP32-Bit Pirate Dock, the printed circuit board in 3D

    ESP32-Bit Pirate Dock

    AndreiVladescu/ESP32-Bit-Pirate-Hardware

    Carrier breaker-board for the ESP32-S3 Devkit. Works great with the ESP32-Bit-Pirate firmware.

    49 parts85CERN-OHL-W-2.0
  • 4 layers19 × 32 mmMalenki hv, the printed circuit board in 3D

    Malenki hv

    MarkR42/malenki-nano

    Speed controller and receiver for small robots

    49 parts73GPL-3.0
  • 4 layers80 × 80 mmZ2203, the printed circuit board in 3D

    Z2203

    brer-rabbit/zoxnoxious

    Analog synth / software interface

    49 parts68GPL-3.0
  • 4 layers42.8 × 36.8 mmDriver board, the printed circuit board in 3D

    Driver board

    blazer82/FT81x_Arduino_Driver

    FT81x on ST7701S Arduino Driver

    49 parts59MIT

Questions

How big is the SYZYGY PHY PCB?

It measures 57.7 × 27 mm and has 4 copper layers, 1.6 mm thick.

What parts does the SYZYGY PHY use?

49 parts, built around the TXV0106BQBR, GPY111 and ARJM11C7-502-KB-EW2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the SYZYGY PHY KiCad files?

From the rustbox/router repository on GitHub, at the commit this page was made from: the board is SYZYGY-PHY/SYZYGY-PHY.kicad_pcb and its schematic SYZYGY-PHY/SYZYGY-PHY.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the SYZYGY PHY design in my own project?

Its repository states no licence, so its author keeps all rights: ask rustbox before reusing the design.