

In this repo we archive rusEfi-related abandoned hardware files
- Size
- 145 × 118 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 230
- Nets
- 290
- Pads
- 963
- Tracks, vias
- 1,586, 150
- Pours
- 18
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 29 Jun 2019
- Updated
- 29 Jun 2023
Overview
M52 is an open-source printed circuit board by rusefi, from the rusefi/hw_legacy repository on GitHub. It is a 2-layer board of 145 × 118 mm with 230 parts on 290 nets, routed with 1,586 tracks and 150 vias.
It is built around the HC-05, SN65HVD230D and NGD8201AN, with the MCP6004-E/P, CP2101-GM and MCP6001OB among its other parts. Its parts include 111 resistors, 37 capacitors, 33 diodes, 20 transistors and 13 ICs.
Main components
12HC-05
Bluetooth to Serial Port ModuleGENERICUncategorisedSN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversNGD8201AN
DPAK-55℃~+175℃ 1.3nF 1.4V 1.5us 1.8V 125W 20A 20pF 440V 50A 80pF 8us DPAK IGBT Transistors / Modules ROHSonsemiIGBT Transistors / ModulesMCP6004-E/P
PDIP-14-40℃~+125℃ 1.8V~6V 100uA 1MHz 1pA 1pA 23mA 28nV/√Hz@1kHz 2uV/℃ 4 4.5mV 600V/ms 76dB ESD protection Rail-to-Rail Input, Rail-to-Rail Output PDIP-14 Operational Amplifier ROHSMicrochip TechnologyOperational AmplifierCP2101-GM
QFN-28(5x5)-40℃~+85℃ 22mA 3V~3.6V 78uA 921.6Kbps USB 2.0 USB to UART QFN-28(5x5) USB Converters ROHSSilicon LabsUSB ConvertersMCP6001OB
SOT-23-5-3V~-900mV、900mV~3V -40℃~+125℃ 1 1.8V~6V 1MHz 1pA 1pA 2.7uV/℃ 27nV/√Hz@1kHz 3.5mV 70dB 75uA 800V/ms 84mA Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5 Operational Amplifier ROHSGREENMICROOperational AmplifierMPXH6115A6U
SOIC-8-300mil-40℃~+125℃ 15Kpa~1.15bar 1ms 2.7V~3.3V On-chip temperature compensation、Integrated signal amplifier Yes SOIC-8-300mil Pressure Sensors ROHSNXP SemiconductorsPressure Sensors74LVC2G04GW
SOT-363-40℃~+125℃ 1.65V~5.5V 1.7V~2V 2 2 2V 3.2ns@5V,50pF 32mA 32mA 4uA 700mV、800mV 74LVC 800mV Schmitt trigger SOT-363 Inverters ROHSNexperiaInvertersTPIC8101DW
SOIC-20-300mil-40℃~+125℃ 10 2 2.5LSB 2.5V 200kHz 5MHz 7500uA Built-in SPI SOIC-20-300mil ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special PurposeLL4148
LL-341 Independent 1V@10mA 200mA 4A 4ns 500mW 5uA@75V 75V LL-34 Switching Diodes ROHSMDDSwitching DiodesPN2222A
TO-92-3-55℃~+150℃ 1 NPN 1A 300MHz 300mV 40V 625mW NPN TO-92-3 Bipolar (BJT) ROHSNTE ElectronicsBipolar (BJT)LL4007
DO-213AB-65℃~+150℃ 1 Independent 1.1V@1A 1A 1kV 30A 5uA@1kV DO-213AB Diodes - General Purpose ROHSSTMicroelectronicsDiodes - General Purpose
README
CJ125_board/readme.md
2019 status: known to work, but documentation is very limited :(
On this board UR and UA do NOT have build-in resistor dividers.
There is an opinion that for open air UA divider is required.
Parts
230| Qty | Value | Footprint | References |
|---|---|---|---|
| 26 | 1K | Resistors_SMD:R_0805 | R3, R11, R15, R16, R19, R23, R27, R33, R34, R35, R36, R38, R40, R43, R102, R104 +10 |
| 20 | 10K | Resistors_SMD:R_0805 | R4, R5, R7, R12, R13, R22, R28, R29, R37, R52, R53, R73, R74, R75, R101, R108 +4 |
| 18 | 1.5K | Resistors_SMD:R_0805 | R17, R18, R20, R21, R41, R42, R44, R45, R64, R65, R69, R70, R80, R81, R116, R117 +2 |
| 16 | 100K | Resistors_SMD:R_0805 | R6, R14, R39, R47, R55, R60, R63, R68, R95, R96, R97, R98, R99, R100, R105, R106 |
| 14 | LL4148 | Diodes_SMD:D_SOD-323 | D1, D2, D3, D9, D13, D15, D17, D20, D22, D23, D26, D27, D28, D31 |
| 13 | 100nF | Capacitors_SMD:C_0805 | C1, C3, C6, C10, C14, C15, C19, C26, C32, C33, C34, C35, C38 |
| 11 | 10nF | Capacitors_SMD:C_0805 | C4, C5, C12, C13, C16, C17, C21, C22, C23, C24, C37 |
| 9 | 100R | Resistors_SMD:R_0805 | R9, R10, R31, R32, R56, R57, R76, R77, R109 |
| 9 | 5.1v | Diodes_SMD:D_SOD-323 | D4, D5, D18, D19, D24, D25, D29, D30, D33 |
| 9 | IRLR3103 | UserParts:IRLR3103 | Q1, Q2, Q4, Q6, Q8, Q10, Q12, Q15, Q18 |
| 6 | 500K | Resistors_SMD:R_0805 | R2, R26, R49, R50, R71, R107 |
| 6 | NGD8201 | UserParts:TO-263-3LeadThermal | Q14, Q17, Q19, Q21, Q23, Q25 |
| 5 | 2.7K | Resistors_SMD:R_0805 | R1, R25, R30, R51, R103 |
| 5 | PN2222A | TO_SOT_Packages_SMD:SOT-23 | Q3, Q20, Q22, Q24, Q26 |
| 4 | 1nF | Capacitors_SMD:C_0805 | C2, C7, C8, C9 |
| 4 | 39K | Resistors_SMD:R_0805 | R87, R88, R90, R91 |
| 3 | 3.3v | Diodes_SMD:D_SOD-323 | D6, D7, D32 |
| 2 | 22R | Resistors_SMD:R_1206 | R24, R94 |
| 2 | 24pF | Capacitors_SMD:C_0805 | C28, C29 |
| 2 | 3.3nF | Capacitors_SMD:C_0805 | C30, C31 |
| 2 | 470uF | Capacitors_SMD:CP_Elec_8x10 | C11, C18 |
| 2 | 500mA | Fuse_Holders_and_Fuses:Fuse_SMD1206_Reflow | F2, F3 |
| 2 | CONN_02X25 | Socket_Strips:Socket_Strip_Straight_2x25 | X2, X3 |
| 2 | LL4007 | Diodes_SMD:D_SMA_Standard | D10, D16 |
| 2 | MCP6004 | Housings_SOIC:SOIC-14_3.9x8.7mm_Pitch1.27mm | IC1, IC7 |
| 1 | 10uF | Capacitors_Tantalum_SMD:CP_Tantalum_Case-C_EIA-6032-28_Reflow | C20 |
| 1 | 120R | Resistors_SMD:R_1206 | R92 |
| 1 | 12v | Diodes_SMD:D_MiniMELF_Standard | D11 |
| 1 | 1uH | Choke_SMD:Choke_SMD_1206_Standard | L1 |
| 1 | 220nF | Capacitors_SMD:C_0805 | C27 |
| 1 | 22v | Diodes_SMD:D_MiniMELF_Standard | D14 |
| 1 | 2M | Resistors_SMD:R_0805 | R83 |
| 1 | 3.5A | Resistors_SMD:R_1812 | F1 |
| 1 | 4.7uF | Capacitors_SMD:C_1206 | C25 |
| 1 | 50K | Resistors_SMD:R_0805 | R72 |
| 1 | 5K | Resistors_SMD:R_0805 | R78 |
| 1 | 74LVC2G04GW | TO_SOT_Packages_SMD:SOT-23-6 | IC5 |
| 1 | 820R | Resistors_SMD:R_0805 | R86 |
| 1 | 8MHz | Crystals:Crystal_SMD_HC49-SD | Y1 |
| 1 | CONN_02X44 | UserConnectors:BOSCH-88pin | X4 |
| 1 | CP2101 | Housings_DFN_QFN:QFN-28-1EP_5x5mm_Pitch0.5mm | IC4 |
| 1 | FAN | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | P1 |
| 1 | GREEN | LEDs:LED_0805 | D21 |
| 1 | HC-05 | HC-05:HC-05 | IC6 |
| 1 | HRD_RST | Buttons_Switches_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | IX4424 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | IC10 |
| 1 | LM340MP-5.0/NOPB | HC-05:SOT-223 | U1 |
| 1 | MAP | Pin_Headers:Pin_Header_Straight_1x06_Pitch2.54mm | P2 |
| 1 | MAX9926 | Housings_SSOP:MSOP-16_3x4mm_Pitch0.5mm | IC2 |
| 1 | MCP6001 | TO_SOT_Packages_SMD:SOT-23-5 | IC15 |
| 1 | MPXH6115 | PressureSensors:MPXH6300 | IC11 |
| 1 | MPXH6400 | PressureSensors:MPXH6300 | IC3 |
| 1 | RED | LEDs:LED_0805 | D8 |
| 1 | SN65HVD230 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | IC9 |
| 1 | SS34 | Diodes_SMD:D_SMA_Standard | D12 |
| 1 | TPIC8101 | Housings_SOIC:SOIC-20W_7.5x12.8mm_Pitch1.27mm | IC8 |
| 1 | USB_OTG | Connect:USB_Micro-B | X1 |
The 226 most common of 230 parts.
More from rusefi/hw_legacy
7- 2 layers145 × 118 mm

- 4 layers

TCPL STM CAN
rusefi/hw_legacy
In this repo we archive rusEfi-related abandoned hardware files
129 parts2 - 2 layers154.1 × 161.7 mm

Frankenso foundation
rusefi/hw_legacy
In this repo we archive rusEfi-related abandoned hardware files
75 parts2 - 2 layers

- 4 layers18.2 × 34.3 mm

O2 input CJ125
rusefi/hw_legacy
In this repo we archive rusEfi-related abandoned hardware files
39 parts2 - 2 layers100 × 99.9 mm

Frankenstein foundation
rusefi/hw_legacy
In this repo we archive rusEfi-related abandoned hardware files
14 parts2 - 2 layers

Low Z LM1949
rusefi/hw_legacy
In this repo we archive rusEfi-related abandoned hardware files
12 parts2
Similar boards
- 2 layers154 × 109 mm

- 4 layers160 × 118 mm

Polygonus Universal Base
FOME-Tech/Polygonus-Universal
Open source 88pin universal base (NOT A PNP)
91 parts4 - 4 layers160 × 118 mm

- 4 layers70 × 157.5 mm

Controller Tv Lift
vyrubaev/TV-Lift-Controller
TVLift Controller is an intelligent controller for TV lift and lower mechanisms, based on the ESP32 microcontroller.
103 parts - 2 layers100 × 100 mm

- 2 layers86 × 117 mm

- 4 layers33 × 66 mm

- 2 layers

Questions
How big is the M52 PCB?
It measures 145 × 118 mm and has 2 copper layers, 1.6 mm thick.
What parts does the M52 use?
230 parts, built around the HC-05, SN65HVD230D, NGD8201AN and MCP6004-E/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the M52 KiCad files?
From the rusefi/hw_legacy repository on GitHub, at the commit this page was made from: the board is Snake____1/M52.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the M52 design in my own project?
Its repository states no licence, so its author keeps all rights: ask rusefi before reusing the design.