

Panel
"Air" sensor hardware
- Size
- 133 × 20 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 158
- Nets
- 65
- Pads
- 353
- Tracks, vias
- 685, 150
- Pours
- 245
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 Aug 2026
- Updated
- 11 Sep 2026
Overview
Panel is an open-source printed circuit board by romkey, from the romkey/sensr-air repository on GitHub. It is a 2-layer board of 133 × 20 mm with 158 parts on 65 nets, routed with 685 tracks and 150 vias.
It is built around the CL05B104KO5NNN, CL05A105KA5NQN and 0402WGF4701, with the BM04B-SRSS-TB(LF)(SN) and 0402WGF470K among its other parts. Its parts include 25 resistors, 20 capacitors, 15 ICs, 15 connectors and 5 diodes. It belongs with the sensors and measurement boards of this library.
Main components
5CL05B104KO5NNN
0402100nF 16V X7R ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSSamsung Electro-MechanicsMultilayer Ceramic Capacitors MLCC - SMD/SMTCL05A105KA5NQN
04021uF 25V X5R ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSSamsung Electro-MechanicsMultilayer Ceramic Capacitors MLCC - SMD/SMT0402WGF4701
0402-55℃~+155℃ 4.7kΩ 50V 62.5mW Thick Film Resistor ±1% ±100ppm/℃ 0402 Chip Resistor - Surface Mount ROHSUNI-ROYALChip Resistor - Surface MountBM04B-SRSS-TB(LF)(SN)
SMD,P=1mm-25℃~+85℃ 1 1A 1mm 1x4P 3.6mm 4 4.25mm 4P 50V 6mm Auxiliary Solder Pin Copper alloy PA SR Surface Mount,Vertical Tin UL94V-0 White SMD,P=1mm Wire To Board Connector ROHSJSTWire To Board Connector0402WGF470K
0402-55℃~+155℃ 4.7Ω 50V 62.5mW Thick Film Resistor ±1% ±200ppm/℃ 0402 Chip Resistor - Surface Mount ROHSUNI-ROYALChip Resistor - Surface Mount
README
README.mdsensr-air
Hardware design and test firmware for a small air quality sensor PCB with:
| Sensor | Function | I2C address |
|---|---|---|
| Sensirion SGP41 | VOC index / NOx index | 0x59 |
| Sensirion STCC4 | CO2 | 0x64 (0x65 if ADDR is high) |
| Sensirion SFA40 | formaldehyde (HCHO) | 0x5D |
| Sensirion SHT40 | temperature / humidity | none — connected to the STCC4's private I2C bus and read through the STCC4 |
| Bosch BMV080 | PM1 / PM2.5 / PM10 | 0x54 |
Boards up to hw/air-stcc4/0.3.0 carry an SGP40 (VOC only) instead of the
SGP41 and have no SFA40. The two SGP parts share address 0x59; the test
firmwares read the SGP4x feature set at startup to tell them apart, so one
build runs on either revision.
This is a 3.3 V board with no voltage regulator — don't use it with 5 V circuits. To simplify it, the board is opinionated about I2C addresses and doesn't expose address selection pins for chips that have them. For reliability I don't recommend putting too many chips on one I2C bus.

AI Disclosure
The board was designed by a human. CI and firmware were generated by AI.
Hardware
Board designs live under hw/, one subdirectory per board with a subdirectory per version:
- hw/air-stcc4/ — STCC4 + SHT40 breakout
- hw/air/ — earlier SCD40 + BME680 board
KiCAD CI
The KiCAD workflow runs
ci/kicad-check.sh, which runs ERC on every schematic and
DRC on every PCB of the latest version of each board under hw/. Only errors
fail the check; warnings are ignored. Boards or versions containing a
.ci-kicad-ignore file are skipped.
Run it locally with KiCAD 8+ installed:
./ci/kicad-check.shkilint CI
The kilint workflow runs
kilint, a linter for KiCAD project
conventions that ERC and DRC don't cover (title blocks, reference designators,
mounting holes, part number fields, net classes, and so on). It runs only when
BOFFF.md is present, and lints the single board that BOFFF.md's
repository_path points at via ci/kilint-check.sh.
Older boards under hw/ predate these conventions and are not checked.
Rule configuration lives in .kilint.yml. kilint has no tagged
releases yet, so the workflow installs it from main; pin KILINT_REF in the
workflow once it does.
Run it locally:
pip install git+https://github.com/romkey/kilint
./ci/kilint-check.shBOFFF
BOFFF.md is this board's machine-readable fabrication/form-factor description (Bill of Form, Fit and Features) - it's a tldr; for important facts about the board. The BOFFF workflow does nothing but assert the file exists, so the BOFFF badge above is green whenever the repo carries one.
Test firmware
Each firmware directory contains a test program that exercises all of the board's sensors, a README, and (where possible) a docker compose file to build it. All of them print/report readings from each sensor so you can verify a freshly assembled board.
| Directory | Platform | SGP41 | STCC4 | SFA40 | SHT40 (via STCC4) | BMV080 |
|---|---|---|---|---|---|---|
| firmware/circuitpython/ | CircuitPython 9+ | yes | yes | yes³ | yes | presence check only¹ |
| firmware/arduino/ | Arduino / ESP32 | yes | yes | yes | yes | yes |
| firmware/esphome/ | ESPHome / ESP32 | yes | yes² | yes⁴ | yes² | yes |
¹ Bosch only ships the BMV080 driver as closed-source precompiled static libraries for specific MCU toolchains, so no CircuitPython driver exists.
² ESPHome has no upstream STCC4 support; this repo includes a local external component for it.
³ Via romkey/circuitpython-sfa40.
⁴ ESPHome's sfa40 component landed upstream after 2026.8, so the ESPHome
build uses the beta channel until a stable release includes it.
CI builds all three firmwares on every push (CircuitPython, Arduino, ESPHome).
License
Hardware designs are licensed under the CERN Open Hardware Licence v2 Permissive. Firmware is licensed under the MIT License.
Parts
158| Qty | Value | Footprint | References |
|---|---|---|---|
| 48 | NPTH | NPTH | KiKit_MB_1_1, KiKit_MB_1_2, KiKit_MB_1_3, KiKit_MB_1_4, KiKit_MB_1_5, KiKit_MB_1_6, KiKit_MB_2_1, KiKit_MB_2_2, KiKit_MB_2_3, KiKit_MB_2_4, KiKit_MB_2_5, KiKit_MB_2_6, KiKit_MB_3_1, KiKit_MB_3_2, KiKit_MB_3_3, KiKit_MB_3_4 +32 |
| 20 | MountingHole_2.2mm_M2 | MountingHole:MountingHole_2.2mm_M2 | M1, M1, M1, M1, M1, M2, M2, M2, M2, M2, M3, M3, M3, M3, M3, M4 +4 |
| 10 | 100nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C1, C1, C1, C1, C2, C2, C2, C2, C2 |
| 10 | 10K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R3, R3, R3, R3, R4, R4, R4, R4, R4 |
| 10 | 1µF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C3, C3, C3, C3, C3, C4, C4, C4, C4, C4 |
| 10 | 4.7K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R1, R1, R1, R1, R2, R2, R2, R2, R2 |
| 10 | BM04B-SRSS-TB(LF)(SN) | easyeda2kicad:CONN-SMD_4P-P1.00_SM04B-SRSS-TB-LF-SN | J1, J1, J1, J1, J1, J2, J2, J2, J2, J2 |
| 5 | 4.7 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R5, R5, R5, R5 |
| 5 | CTRLH Logo | 1myFootprints:CTRLH Logo | GRPH1, GRPH1, GRPH1, GRPH1, GRPH1 |
| 5 | Conn_01x05 | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J3, J3, J3, J3, J3 |
| 5 | PWR | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D1, D1, D1, D1 |
| 5 | SGP40 | easyeda2kicad:DFN-6_L2.4-W2.4-P0.80-TL-EP | U3, U3, U3, U3, U3 |
| 5 | SHT40 | easyeda2kicad:DFN-4_L1.5-W1.5-P0.80-TL-EP | U2, U2, U2, U2, U2 |
| 5 | STCC4 | easyeda2kicad:LAG-8_L4.0-W3.0-P1.15-TL | U1, U1, U1, U1, U1 |
The 153 most common of 158 parts.
More from romkey/sensr-air
3Similar boards
- 2 layers70 × 71 mm

Jewelled lc1
matthiasnowak/jewelled
This is a panel meant for production of the Earrings, allowing for 2 Earrings per panel.
148 parts3 - 4 layers18 × 13 mm

Mumo
kounocom/Mumo
A compact 13×18mm IMU module featuring the TDK InvenSense ICM-45686 6-axis IMU with integrated 32.768kHz clock and QST QMC6309H 3-axis magnetometer.
25 parts41CERN-OHL-S-2.0 - 4 layers50 × 20 mm

- 4 layers100 × 60 mm

GigaDFN56
kaminaris/GigaESC-DFN5x6
Compact, modular three-phase ESC power board for the GigaESC project. Designed in KiCad 10 on a 100 × 60 mm, four-layer PCB, with separate plug-in control and power-supply boards.
234 parts - 4 layers33.5 × 66.8 mm

Net bmp
elagil/net-bmp
An Ethernet-connected SWD/JTAG debug adapter (blackmagic probe)
97 parts3GPL-3.0 - 2 layers26 × 32 mm

- 4 layers82.5 × 82.5 mm

Core board
stellarcorp/tvsc
Core software repository for the Tennessee Valley Stellar Corporation
150 parts1MIT - 2 layers84.3 × 39.4 mm

Shutdown manager mainboard
testudor/shutdown-manager-mainboard
Power input module for 3D printers capable of performing safe shutdown procedures for SBCs like Raspberry PIs
28 parts1CC-BY-SA-4.0
Questions
How big is the Panel PCB?
It measures 133 × 20 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Panel use?
158 parts, built around the CL05B104KO5NNN, CL05A105KA5NQN, 0402WGF4701 and BM04B-SRSS-TB(LF)(SN). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Panel KiCad files?
From the romkey/sensr-air repository on GitHub, at the commit this page was made from: the board is hw/air-stcc4/0.2.0/panel.kicad_pcb and its schematic hw/air-stcc4/0.1.0/air-stcc4.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Panel design in my own project?
Its repository states no licence, so its author keeps all rights: ask romkey before reusing the design.

