Skip to the content
4 layers30.5 × 62 mmEsp32 rover devkit, the printed circuit board in 3D

Esp32 rover devkit

robotique-udes/PCB
Size
30.5 × 62 mm
Copper layers
4
Thickness
1.6 mm
Parts
27
Nets
55
Pads
154
Tracks, vias
198, 37
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
26 Mar 2024
Updated
3 Nov 2026

Overview

Esp32 rover devkit is an open-source printed circuit board by robotique-udes, from the robotique-udes/PCB repository on GitHub, published under the MIT licence. It is a 4-layer board of 30.5 × 62 mm with 27 parts on 55 nets, routed with 198 tracks and 37 vias.

It is built around the ESP32-S3-WROOM-1-N8, AZ1117ID-3.3TRG1 and RJ45, with the TS09-63-25-WT-160-SMT-TR among its other parts. Its parts include 8 capacitors, 5 ICs, 3 resistors, 3 connectors and 2 diodes. It belongs with the robots and motor control boards and the ESP32 boards of this library.

Main components

4

README

rover/2024/pdb/README.md

PDB (Power Distribution Board)

PCB servant à gérer la distribution à bas courant et le de data du rover

Image du PCB en 3D

Capture d’écran, le 2024-09-18 à 21 24 36

Objectifs:

  • Protéger tous les autres boards du Over/Under Voltage pour le 5V, 12V et 24V
    • Seulement le 5v et le 24v sont protégé, car les résistance 5% ont trop d'incertitude.
  • Injecteur POE(12V custom pinout) pour les cameras branché en Ethernet
    • On/Off possible par le MCU
  • Diriger le signal des cameras sur les bonnes pins selon la norme Ethernet
  • Agir en tant que POE pour les antennes 24V (vrai POE)
  • Controller l'alimentation de 2 circuit d'accessoires 12V
    • Par 2 connecteurs Ethernet
  • Permettre de pouvoir sortir une des 3 tension (5v, 12v, 24v) par un screw terminal
    • Alimente la switch ethernet en dessous
  • MCU Connecté sur le CAN BUS
  • Sélectionner avec les GPIO les cameras qui doivent recevoir du power

Composants principaux:

  • ESP32 DEV KIT V1
  • TJA1050 (CAN BUS)
  • LTC4365 (Over/Under Voltage protaction)
  • DMG4822SSD (DIODE pour la switch du LTC4365)
  • DELs
  • CLP6C-FKB-CKNPRGJBB7A363 (ERROR DEL)
  • Boutons
  • Horizontal Amphenol 54602 RJ45
  • ASSMANN_A-2014 Ethernet connector
  • CRJ036-5-TH_2x4 Ethernet connector
  • BTS5200 (4 Channel Mosfet)

Fonctionnement:

  • Le PDB reçoit 3 tensions régulé en entrée, du 5V, du 12V et du 24V.
  • Le 12V sert principalement pour alimenter les caméras qui sont alimentés avec un POE avec un Pinout spécial. Il sert aussi à alimenter 2 circuit d'accessoires potentiels.
  • Le 24V sert à alimenter le/les antennes qui sont sur le Rover.
  • Le 5V est passé avec les fils de CanBus pour alimenter et communiquer avec les autres PCB du rover
  • Le circuit sécurise les trois tensions contre les sur-tensions et le drops de tensions.
  • La sortie vers l'ordinateur principal n'est pas utilisé, l'ordinateur est directement branché dans la switch.

PGIO

Outputs

NameGPIO
CAM_SIGN_0D18
CAM_SIGN_1D19
CAM_SIGN_2D33
CAM_SIGN_3D32
PWM_0D21
PWM_1D22
ACC1_CONTROLD23
ACC2_CONTROLD25
LED_RD14
LED_GD27
LED_BD26

Communication

NameGPIO
TXCD6
RXCD7

Parts

27
QtyValueFootprintReferences
4100nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2, C4, C5, C8
4MountingHole_PadMountingHole:MountingHole_2.2mm_M2_DIN965_Pad_TopBottomH1, H2, H3, H4
210uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC6, C7
21kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR2, R3
2RLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD1, D2
2RJ4554601-908WPLF:AMPHENOL_54601-908WPLFJ2, J3
2TS09-63-25-WT-160-SMT-TRTS09_63_25_WT_160_SMT_TR:SW_TS09-63-25_CUDSW1, SW2
110K TBVResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1
11uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3
122uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1
1AZ1117ID-3.3TRG1LDO_AZ1117ID-3.3TRG1:TO252-2_AZ1117ID-3.3TRG1_DIOU2
1ESP32-S3-WROOM-1RF_Module:ESP32-S3-WROOM-1U1
1TJA1050T_CM_118TJA1050T_CM_118:SOIC127P600X175-8NU3
1USB_B_MicroConnector_USB:USB_Micro-B_Amphenol_10118193-0001LF_HorizontalJ1
1~Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mmU5
1~Custom:BN-880U4

More from robotique-udes/PCB

12
  • 4 layers152.8 × 53.5 mmDDB, the printed circuit board in 3D

    DDB

    robotique-udes/PCB

    110 partsMIT
  • 4 layers100 × 80 mmArmJ345, the printed circuit board in 3D

    ArmJ345

    robotique-udes/PCB

    98 partsMIT
  • 4 layers96.5 × 97.9 mmPdb, the printed circuit board in 3D

    Pdb

    robotique-udes/PCB

    96 partsMIT
  • 4 layers57.8 × 80 mmArm drive, the printed circuit board in 3D

    Arm drive

    robotique-udes/PCB

    69 partsMIT
  • 4 layers80 × 50 mmArm drive jl, the printed circuit board in 3D

    Arm drive jl

    robotique-udes/PCB

    62 partsMIT
  • 4 layers59.5 × 90 mmGripper 2024, the printed circuit board in 3D

    Gripper 2024

    robotique-udes/PCB

    60 partsMIT
  • 4 layers38 × 76 mmArm drive j2, the printed circuit board in 3D

    Arm drive j2

    robotique-udes/PCB

    58 partsMIT
  • 4 layers69.1 × 53 mmArmJ2, the printed circuit board in 3D

    ArmJ2

    robotique-udes/PCB

    57 partsMIT
  • 4 layers79.5 × 36 mmArmJL, the printed circuit board in 3D

    ArmJL

    robotique-udes/PCB

    57 partsMIT
  • 4 layers32.5 × 59.3 mmDrive 27A, the printed circuit board in 3D

    Drive 27A

    robotique-udes/PCB

    53 partsMIT

Similar boards

  • 2 layers80 × 66 mmLw6017rWifi, the printed circuit board in 3D

    Lw6017rWifi

    ImTheSquid/lw6017r

    A custom PCB to control my LG LW6017R A/C unit through Wi-Fi

    66 parts
  • 2 layers43.7 × 43.9 mmPcb n as5600, the printed circuit board in 3D

    Pcb n as5600

    khuntiasmriti/pcb-n-as5600

    34 parts
  • 2 layers93.2 × 65 mmSTM32H723 SDC Ver 1, the printed circuit board in 3D

    STM32H723 SDC Ver 1

    manhtienvu-vn/Defensive_Robot

    Full neccessary document my team PKA-03 (Phenikaa University) used to build a defensive robot in the Vietnam Robocon competition 2025, including firmware, hardware and mechanical design.

    67 parts
  • 4 layers127 × 101.6 mmS Band Transceiver, the printed circuit board in 3D

    S Band Transceiver

    tkeller12/openEPR

    Open-Source EPR Spectrometer

    224 parts1MIT
  • 2 layers66.3 × 70.3 mmBldc driver, the printed circuit board in 3D

    Bldc driver

    acanyulaf/24V-10A-BLDC-Driver

    This is a technical assignment problem given by Kuartis. The aim is to design a 24V/10A BLDC controller. There will be also an I2C or SPI interface for control inputs.

    66 parts
  • 2 layers100 × 60 mmA NET, the printed circuit board in 3D

    A NET

    NewsanLab/ARCHINET

    ArchiNet para conectividad WiFi/BLE/Ethernet mediante Archi

    106 parts1
  • 4 layers80.5 × 42.7 mmSnakeTank 4 sig pwr gnd sig, the printed circuit board in 3D

    SnakeTank 4 sig pwr gnd sig

    vpolda/Snake-Tank

    A DIY reptile tank monitor for remote monitoring and data collection.

    49 parts1
  • 2 layers101.6 × 101.6 mmAndromeda, the printed circuit board in 3D

    Andromeda

    ncarpenedo/AndromedaPCB

    109 parts

Questions

How big is the Esp32 rover devkit PCB?

It measures 30.5 × 62 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Esp32 rover devkit use?

27 parts, built around the ESP32-S3-WROOM-1-N8, AZ1117ID-3.3TRG1, RJ45 and TS09-63-25-WT-160-SMT-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Esp32 rover devkit KiCad files?

From the robotique-udes/PCB repository on GitHub, at the commit this page was made from: the board is rover/2024/esp32_rover_devkit/esp32_rover_devkit.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Esp32 rover devkit design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).