

Lw6017rWifi
A custom PCB to control my LG LW6017R A/C unit through Wi-Fi
- Size
- 80 × 66 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 66
- Nets
- 86
- Pads
- 290
- Tracks, vias
- 614, 100
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 17 Jul 2024
- Updated
- 24 Jul 2024
Overview
Lw6017rWifi is an open-source printed circuit board by ImTheSquid, from the ImTheSquid/lw6017r repository on GitHub. It is a 2-layer board of 80 × 66 mm with 66 parts on 86 nets, routed with 614 tracks and 100 vias.
It is built around the ESP32-S3-WROOM-1-N8, FT230XQ-R and TPD3E001DRLR, with the AZ1117ID-3.3TRG1 and TXB0104D among its other parts. Its parts include 24 resistors, 10 capacitors, 10 diodes, 8 ICs and 6 switches. It belongs with the ESP32 boards of this library.
Main components
5ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesFT230XQ-R
QFN-16-EP(4x4)-40℃~+85℃ 125uA 3.3V~5V 8mA USB 2.0 USB to UART QFN-16-EP(4x4) USB Converters ROHSFTDIUSB ConvertersTPD3E001DRLR
SOT(5x3)-40℃~+85℃ 1.5pF 11V 1nA 5.5A@8/20us 5.5V 90W ESD IEC 61000-4-2 Three channels Unidirectional SOT(5x3) ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsESD And Surge Protection (TVS/ESD)AZ1117ID-3.3TRG1
TO-252-2-40℃~+125℃@(Tj) 0.003%Vout 1 1.4V@(0.8A) 15V 1A 3.3V 6mA 70dB@(120Hz) Fixed Over Temperature Protection Positive TO-252-2 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTXB0104D
SOIC-14-40℃~+85℃ 1 1.2V~3.6V 1.65V~5.5V 100Mbps 4 Auto Direction Detection Bidirectional CMOS CMOS Tri-State SOIC-14 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
Parts
66| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C3, C4, C5, C6, C7, C8, C9, C10 |
| 8 | 51 | Resistor_SMD:R_0402_1005Metric | R15, R16, R17, R18, R19, R20, R21, R22 |
| 6 | 3.3k | Resistor_SMD:R_0402_1005Metric | R9, R10, R11, R12, R13, R14 |
| 4 | 120 | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4 |
| 4 | 5.1K | Resistor_SMD:R_0402_1005Metric | R5, R6, R23, R24 |
| 2 | D | Diode_SMD:D_SOD-323 | D9, D10 |
| 2 | D_TVS | Diode_SMD:D_SOD-882 | D7, D8 |
| 2 | TPD3E001DRLR | Package_TO_SOT_SMD:SOT-553 | U6, U8 |
| 2 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2, J3 |
| 1 | 100 | Resistor_SMD:R_0402_1005Metric | R8 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 330 | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 353630860 | footprints:CON_353630860 | J1 |
| 1 | AZ1117ID-3.3TRG1 | Package_TO_SOT_SMD:TO-252-2 | U4 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | COOL | LED_THT:LED_D5.0mm | D1 |
| 1 | DRY | LED_THT:LED_D5.0mm | D4 |
| 1 | ESP32-S3-WROOM-1 | PCM_Espressif:ESP32-S3-WROOM-1 | U1 |
| 1 | E_SAVER | LED_THT:LED_D5.0mm | D2 |
| 1 | FAN | LED_THT:LED_D5.0mm | D3 |
| 1 | FAN_SPEED | Button_Switch_THT:SW_PUSH_6mm | SW4 |
| 1 | FT230XQ | Package_DFN_QFN:QFN-16-1EP_4x4mm_P0.65mm_EP2.1x2.1mm | U7 |
| 1 | F_REMIND | LED_THT:LED_D5.0mm | D5 |
| 1 | HDSM-441W | Display:HDSM-441B_HDSM-443B | U3 |
| 1 | MODE | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | POWER | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | TEMP_DN | Button_Switch_THT:SW_PUSH_6mm | SW6 |
| 1 | TEMP_UP | Button_Switch_THT:SW_PUSH_6mm | SW5 |
| 1 | TIMER | LED_THT:LED_D5.0mm | D6 |
| 1 | TIMER | Button_Switch_THT:SW_PUSH_6mm | SW3 |
| 1 | TSOP382xx | OptoDevice:Vishay_MINICAST-3Pin | U5 |
| 1 | TXB0104D | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2 |
The 62 most common of 66 parts.
Similar boards
- 4 layers30.5 × 62 mm

- 4 layers127 × 101.6 mm

- 2 layers66.3 × 70.3 mm

Bldc driver
acanyulaf/24V-10A-BLDC-Driver
This is a technical assignment problem given by Kuartis. The aim is to design a 24V/10A BLDC controller. There will be also an I2C or SPI interface for control inputs.
66 parts - 4 layers160 × 73.2 mm

MainPCB
doppelgrau/esp32-f9p-io-board
An IO-PCB (two motor-driver/H-bridge, CAN, RS232, ADS1115, relay, ethernet, ardusimple f9p compatible connector) with an ESP32 for 12V power, three 15V tolerant analog inputs, three 5V tolerant inputs.
162 parts39 - 4 layers536.5 × 385.7 mm

- 2 layers50 × 50 mm

- 2 layers60 × 30 mm

- 4 layers23 × 51.5 mm

Power meter pcb
monash-human-power/power-meter
Power meter designed as part of Oscar Varney and Jotham Gates' FYP in 2024
64 partsMIT
Questions
How big is the Lw6017rWifi PCB?
It measures 80 × 66 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Lw6017rWifi use?
66 parts, built around the ESP32-S3-WROOM-1-N8, FT230XQ-R, TPD3E001DRLR and AZ1117ID-3.3TRG1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Lw6017rWifi KiCad files?
From the ImTheSquid/lw6017r repository on GitHub, at the commit this page was made from: the board is lw6017rWifi/lw6017rWifi.kicad_pcb and its schematic lw6017rWifi/lw6017rWifi.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Lw6017rWifi design in my own project?
Its repository states no licence, so its author keeps all rights: ask ImTheSquid before reusing the design.