Skip to the content
2 layers17.8 × 25.4 mmHardware watchdog, the printed circuit board in 3D

PCB Hardware watchdog based on TPL5010

Size
17.8 × 25.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
11
Pads
48
Tracks, vias
51, 3
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
9 Feb 2023
Updated
9 Feb 2023

Overview

Hardware watchdog is an open-source printed circuit board by rmingon, from the rmingon/hardware-watchdog repository on GitHub. It is a 2-layer board of 17.8 × 25.4 mm with 14 parts on 11 nets, routed with 51 tracks and 3 vias.

It is built around the TPL5010EVM. Its parts include 1 resistor, 1 IC, 1 connector and 1 switch.

Main components

1

README

README.md

Hardware PCB - LICENCE (CC BY-NC-SA 4.0)

Based on TPL5010

For work you will need solder ONE jumper for setting delay of watchdog

PINOUT

  • VDD - 1.8 to 5.5V
  • GND
  • DELAY (DLY) - Time Interval set and Manual Reset
  • DONE - Logic Input for watchdog functionality
  • WAKE - Timer output signal generated every Digital pulsed signal to wake up the µC at the end of tIP period.
  • RST - Reset Output (open drain output)

You can too add your delay with the 'delay' (DLY on silkscreen) see bellow (MORE IN DATASHEET)

DELAY

TODO
  • Add TPL5010
  • Add resistor for 100MS
  • Add resistor for 500MS
  • Add resistor for 1S
  • Add resistor for 3S
  • Add resistor for 5S

3D VIEW

3D VIEW

PCB VIEW

PCB VIEW

SCHEMATIC VIEW

SCHEMATIC VIEW

Parts

14
QtyValueFootprintReferences
5Jumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm , JP1, JP2, JP4, JP5
110KResistor_SMD:R_0201_0603MetricR5
12.5KResistor_SMD:R_0201_0603Metric500MS
15.2KResistor_SMD:R_0201_0603Metric1S
1500Resistor_SMD:R_0201_0603Metric100MS
17.628KResistor_SMD:R_0201_0603Metric3S
18.85KResistor_SMD:R_0201_0603Metric5S
1Conn_01x06Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ1
1SW_PushButton_Switch_SMD:SW_SPST_B3U-1000PSW1
1TPL5010Package_TO_SOT_SMD:SOT-23-6U1

Similar boards

  • 4 layers85 × 85 mmEPS, the printed circuit board in 3D

    EPS

    rgw3d/1KCubeSat_Hardware

    Hardware design files for my $1000 CubeSat.

    657 parts158GPL-3.0
  • 2 layersSuntastic, the printed circuit board in 3D

    Suntastic

    snorkman88/suntastic

    An ultra low-power management board for IoT devices

    120 parts13Apache-2.0
  • 2 layers57 × 57 mmMold detect, the printed circuit board in 3D

    Mold detect

    christopher-besch/mold_detect

    Warn residents of mold-friendly atmosphere and log opened windows.

    46 parts4MIT
  • 4 layers80 × 80 mmEPS, the printed circuit board in 3D

    EPS

    4111Spyglass/Hardware_CSAT

    243 parts1
  • 2 layers124.1 × 112 mmAg diy pro, the printed circuit board in 3D

    Ag diy pro

    Open-Air-Foundation/pcb-one

    AirGradient ONE is a desktop indoor air quality monitor built around an ESP32-C3 module. It measures particulate matter (Plantower PMS5003), CO₂ (Senseair S8), temperature and humidity (SHT4x), and VOC (SGP41), with…

    65 parts1CC-BY-SA-4.0
  • 2 layers57 × 44 mmOpenair main, the printed circuit board in 3D

    Openair main

    Open-Air-Foundation/pcb-openair-main

    The Open Air main board carries the monitor's ESP32-C3 MCU, USB-C power input with a 3.3 V LDO, a TPL5010 hardware watchdog, status LEDs and a push button, and the Molex connectors the plug-in sensor modules attach to.

    38 parts1CC-BY-SA-4.0
  • 2 layers49 × 38 mmMailboxSensorProcessor, the printed circuit board in 3D

    MailboxSensorProcessor

    kevinkessler/MailSensors-PCB

    PCB for the MailSensor Lora project

    24 parts
  • 4 layers45.6 × 45.6 mmNearfi pcb, the printed circuit board in 3D

    Nearfi pcb

    mauriciobarroso/nearfi_pcb

    50 partsMIT

Questions

How big is the Hardware watchdog PCB?

It measures 17.8 × 25.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Hardware watchdog use?

14 parts, built around the TPL5010EVM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Hardware watchdog KiCad files?

From the rmingon/hardware-watchdog repository on GitHub, at the commit this page was made from: the board is pcb/pcb.kicad_pcb and its schematic pcb/pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Hardware watchdog design in my own project?

Its repository states no licence, so its author keeps all rights: ask rmingon before reusing the design.