

Drone
Drone uses machine vision to stabilize itself
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 61
- Nets
- 80
- Pads
- 264
- Tracks, vias
- 475, 106
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 29 Jun 2024
- Updated
- 29 Jun 2024
Overview
Drone is an open-source printed circuit board by rmingon, from the rmingon/drone-vision repository on GitHub. It is a 2-layer board of 100 × 100 mm with 61 parts on 80 nets, routed with 475 tracks and 106 vias.
It is built around the ESP32-WROOM-32, MCP8063-E/MD and BMP280, with the LM1117MP-3.3, MPU-9250 and WS2812B among its other parts. Its parts include 20 capacitors, 10 resistors, 8 ICs, 4 connectors and 2 switches. It belongs with the robots and motor control boards and the ESP32 boards of this library.
Main components
7ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesMCP8063-E/MD
DFN-8-EP(4x4)-40℃~+125℃ 1.5A 1.6A 600mΩ Three Phase Yes DFN-8-EP(4x4) Brushless DC (BLDC) Motor Driver ROHSMicrochip TechnologyBrushless DC (BLDC) Motor DriverBMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure SensorsLM1117MP-3.3
SOT-2230℃~+125℃@(Ta) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA 99uVrms Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMPU-9250
QFN-24-EP(3x3)-40℃~+85℃ 2.4V~3.6V 8uA IMU (accelerometer + gyroscope) Motion event detection SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(3x3) Accelerometers ROHSTDK InvenSenseAccelerometersWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedXT30PW-M
-- Power connector / plug connector ROHSChangzhou Amass ElecUncategorised
README
README.mdAUTOMATIC DRONE MACHINE VISION PROJECT
This project exist for make automatic positioning and flying with vision analyse technology
DRONE VISION
3D VIEW
SCHEMATIC VIEW
PCB VIEW
Parts
61| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | C | Capacitor_SMD:C_0603_1608Metric | C4, C5, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 +4 |
| 12 | TestPoint | TestPoint:TestPoint_Pad_3.0x3.0mm | TP1, TP2, TP3, TP6, TP7, TP8, TP10, TP11, TP12, TP14, TP15, TP16 |
| 8 | 10K | Resistor_SMD:R_0603_1608Metric | R3, R4, R5, R6, R7, R10, R11, R12 |
| 4 | MCP8063 | Package_DFN_QFN:DFN-8-1EP_4x4mm_P0.8mm_EP2.5x3.6mm | U3, U5, U6, U7 |
| 4 | TestPoint | TestPoint:TestPoint_Pad_1.0x1.0mm | TP4, TP5, TP9, TP13 |
| 2 | 100K | Resistor_SMD:R_0603_1608Metric | R8, R9 |
| 2 | Conn_01x08_Pin | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J3, J4 |
| 2 | SW_Push_Open | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1, SW2 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U4 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U2 |
| 1 | LM1117MP-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U9 |
| 1 | MPU-9250 | Sensor_Motion:InvenSense_QFN-24_3x3mm_P0.4mm | U8 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
| 1 | XT30PW-M | Connector_AMASS:AMASS_XT30U-F_1x02_P5.0mm_Vertical | J2 |
Similar boards
- 2 layers115 × 115 mm

- 2 layers97 × 97 mm

- 2 layers98.5 × 98.5 mm
.kicad_pcb.jpg?size=s&soon)
- 4 layers70 × 70 mm

IMU V100
embeddedalpha/IMU_V100
Inertial Measurement Unit based around STM32F407VGT6. This is a product development repo.
40 parts1 - 2 layers80 × 61 mm

- 2 layers185 × 115 mm

PCB Corrected
arnaumora/TFG-Plataforma-Instrumentacion-Avionica
An ESP32-S3 sensor unit, built on a custom KiCad-designed PCB, estimates aircraft attitude, heading, altitude and vertical speed in real time and streams them over a 2.4 GHz RF link to a Primary Flight Display (PFD)…
55 partsMIT - 2 layers50 × 50 mm

Rc helicopter mainboard
ikajdan/rc-helicopter-mainboard
RC helicopter mainboard based on an STM32 MCU
54 partsCERN-OHL-P-2.0 - 2 layers55 × 94.5 mm

Questions
How big is the Drone PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Drone use?
61 parts, built around the ESP32-WROOM-32, MCP8063-E/MD, BMP280 and LM1117MP-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Drone KiCad files?
From the rmingon/drone-vision repository on GitHub, at the commit this page was made from: the board is drone/drone/drone.kicad_pcb and its schematic drone/drone/drone.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Drone design in my own project?
Its repository states no licence, so its author keeps all rights: ask rmingon before reusing the design.