Skip to the content
2 layers44 × 22 mmBatt swap, the printed circuit board in 3D

Multi-Agent Mission Concept for Battery Optimized Onsite Swapping Technology (BOOST)

Size
44 × 22 mm
Copper layers
2
Thickness
1.6 mm
Parts
16
Nets
8
Pads
49
Tracks, vias
80, 5
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
6 Oct 2023
Updated
22 Jun 2025

Overview

Batt swap is an open-source printed circuit board by RIVeR-Lab, from the RIVeR-Lab/BOOST repository on GitHub, published under the MIT licence. It is a 2-layer board of 44 × 22 mm with 16 parts on 8 nets, routed with 80 tracks and 5 vias.

It is built around the LTC4412ES6#TRPBF, AOD407 and C2012JB1V226M125AC, with the CL21B105KBFNNNE among its other parts. Its parts include 3 resistors, 3 connectors, 2 capacitors, 2 diodes and 2 transistors.

Main components

4

README

electrical/kicad/Minibot_V1/README.md

Autonomous Navigation & Docking for Distributed Robots

  • Aka Swarm Crawler
  • Aka BOOST: Battery Optimized On-site Swapping Technology
  • Making swarms crawl

Where Software Is

/hubbot_software/

  • The software running on the NVidia Jetson Nano on the HubBot
  • Includes the main ROS2 node running on the HubBot in hubbot_software\ros2_ws\src\py_hubbot_main_controller_node\py_hubbot_main_controller_node

/minibot_hubbot_firmware/charge_controller_firmware/

  • Code running on the Arduino Nano on the HubBot that controls the LEDs and reads battery module continuity and voltage and sends to Jetson Nano over UART.

/minibot_hubbot_firmware/firmwarePioCube/

  • Code running on the STM32F466RE NUCLEO on our Custom PCB.
  • This board is identical on the 2x minibots and on the hubbot.
  • Controls IMU, GPS, motor control, encoders, battery voltage.

/shared/

  • Data shared on the ROS network between HubBot and Minibots

/software/

  • All SLAM and NAV software running on MiniBot for autonomous Docking

Running Things

HubBot Software

  • Run main ROS2 HubBot node:

    ./hubbot_software\start_hubbot_processes.sh

HubBot Firmware

  • Load Firmware onto Charge Controller Arduino Nano.
    • Load this sketch onto the Arduino
    • minibot_hubbot_firmware\charge_controller_firmware\monitor_RGB
  • Load firmware onto STM32F446
    • Load the latest firmware onto the NUCLEO found here:
      • minibot_hubbot_firmware\firmwarePioCube\firmware_releases\hubbot

MiniBot Firmware

  • Load the latest firmware for the respective MiniBot onto its STM32F446RE
    • minibot_hubbot_firmware\firmwarePioCube\firmware_releases

David Useful Commands

ros2 topic pub /chatter std_msgs/String "data: Hello ROS Developers"

ros2 topic pub /hub_stat std_msgs/Int32 "data: 4"

rosserial with ROS1
To find the USB Port and get Nucleo board USB into WSL
To give user permission to /dev/ttyUSBx, ttyACMx, and ttySx devices
  • These devices are in the dialout group, so add your user to that group

    $ sudo adduser myusername dialout

Getting Data into ROS1 from MCU
  • http://wiki.ros.org/rosserial_arduino/Tutorials/Hello%20World
  • run roscore in one terminal
    • wsl> roscore
  • Run serial_node.py in another terminal
    • wsl> rosrun rosserial_python serial_node.py _port:=/dev/ttyACM0 _baud:=57600
    • This will get all topics from the MCU.
  • Should now see the topic in ROS1 in another terminal
    • wsl> rostopic list
    • Can echo with wsl> rostopic echo
Using ros1_bridge
  • https://github.com/ros2/ros1_bridge
  • Start ROS1 core wsl> roscore
    • If not done already.
  • Need to source both ROS1 and then ROS2 setup.bash's
  • wsl> ros2 run ros1_bridge dynamic_bridge --bridge-all-topics
    • This will bring in all topics from ROS1 to ROS2 and all topics from ROS2 to ROS1.
teleop twist keyboard
ROSSerial TroubleShooting
[ERROR] [1677681154.605087]: Unable to sync with device; possible link problem or link software version mismatch such as hydro rosserial_python with groovy Arduino
  • Make sure Baud rates are matching
  • Make sure that LOGGING is off on the nucleo so that ONLY ROSserial stuff is is sent out over the serial port connected to the Jetson.
If serial isn't getting to jetson, but is getting to laptop
  • Make sure that the power configuration is correct on the NUCLEO board.
  • i.e. since we are using the STLink as a serial to USB adapter, the STLINK must be powered when the MCU is booted.
  • Make sure that we are powering USB through NUCLEO from the jetson.
    • And if we are using external 5v to power NUCLEO that the correct jumpers are set.

For running ROSserial and ros1_bridge

source ros1 roscore rosrun rosserial_python serial_node.py _port:=/dev/ttyACM0 _baud:=57600

source ros2 source ros1 ros2 run ros1_bridge dynamic_bridge --bridge-all-topics

Parts

16
QtyValueFootprintReferences
3, ,
3Res3Miscellaneous Devices.IntLib:J1-0603R1, R2, R3
2436500400swarm_crawler_pcb.PcbLib:CON_436500400_MOLJ1, J2
2AOD407swarm_crawler_pcb.PcbLib:TO252_AOSQ1, Q2
2SD103AWS-7-Fswarm_crawler_pcb.PcbLib:SOD323_DIOD1, D2
1436500600swarm_crawler_pcb.PcbLib:CON_436500600_MOLJ3
1C2012JB1V226M125ACswarm_crawler_pcb.PcbLib:CAP_2012_TDKC1
1CL21B105KBFNNNEswarm_crawler_pcb.PcbLib:CAP_CL21_SAMC2
1LTC4412ES6#TRPBFswarm_crawler_pcb.PcbLib:LTC4412ES6#TRPBF_ADIU1

More from RIVeR-Lab/BOOST

2
  • 6 layers80 × 98 mmMinibot V1, the printed circuit board in 3D

    Minibot V1

    RIVeR-Lab/BOOST

    Multi-Agent Mission Concept for Battery Optimized Onsite Swapping Technology (BOOST)

    101 parts3MIT
  • 2 layers36 × 16 mmDocking connector, the printed circuit board in 3D

    Docking connector

    RIVeR-Lab/BOOST

    Multi-Agent Mission Concept for Battery Optimized Onsite Swapping Technology (BOOST)

    7 parts3MIT

Similar boards

  • 2 layers89.2 × 63.5 mmHF PA v10, the printed circuit board in 3D

    HF PA v10

    kholia/HF-PA-v10

    HF-PA-v10 ;) Is this the end of the search for a 5W Digital PA? HF-PA-v10 is now a rugged 10W PA! We also do 100W+ now ;)

    59 parts24
  • 4 layers100 × 100.1 mmMaster-4layers, the printed circuit board in 3D

    Master-4layers

    DepBo/AquaCare

    AquaCare là hệ thống theo dõi và quản lý nuôi trồng thủy sản, gồm ứng dụng web, ứng dụng di động và backend kết nối dữ liệu cảm biến với thiết bị trong ao/bể.

    135 parts1
  • 2 layers175 × 120 mmJackOfAllTradesV2p0, the printed circuit board in 3D

    JackOfAllTradesV2p0

    czalinski/ThlHwTestDevices

    KiCad designs, firmware and documentation for circuits that support testing of electrical hardware, such as HASS and HALT testing.

    172 partsMIT
  • 2 layers61 × 96.4 mmCircuit Boards, the printed circuit board in 3D

    Circuit Boards

    hansgaensbauer/Cat-Counter-Measures

    Counter Cat Countermeasures

    75 parts
  • 4 layers83 × 100 mmSolar module-1u si, the printed circuit board in 3D

    Solar module-1u si

    oresat/oresat-solar-hardware

    OreSat solar array designs and CAD

    148 parts28
  • 2 layers83 × 100 mm1u panel v1, the printed circuit board in 3D

    1u panel v1

    BrownSpaceEngineering/PVDX-Solar_PCB

    75 parts
  • 4 layers50 × 40 mmRAPS-5 V1, the printed circuit board in 3D

    RAPS-5 V1

    itsTasos/RAPS-5

    Dual-input power module with independent LiPo protection, buck conversion and ideal-diode OR-ing.

    96 parts
  • 2 layers100 × 60 mmAlarming AC Enclosure, the printed circuit board in 3D

    Alarming AC Enclosure

    manhoosbilli1/atmega328-enclosure-tamper-alarm

    ATmega328 AC enclosure tamper/intrusion alarm with LTC2960 voltage monitor, LTC4412 PowerPath, boost+buck converters

    98 parts

Questions

How big is the Batt swap PCB?

It measures 44 × 22 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Batt swap use?

16 parts, built around the LTC4412ES6#TRPBF, AOD407, C2012JB1V226M125AC and CL21B105KBFNNNE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Batt swap KiCad files?

From the RIVeR-Lab/BOOST repository on GitHub, at the commit this page was made from: the board is electrical/kicad/batt_swap/batt_swap.kicad_pcb and its schematic electrical/kicad/Minibot_V1/Connectors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Batt swap design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).