2 layers65 × 30 mm
2 layers152 × 85 mm
Work Done in Embedded Systems as a part of course
- Size
- 152 × 85 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 238
- Nets
- 191
- Pads
- 828
- Tracks, vias
- 2,396, 415
- Pours
- 13
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 19 Jun 2017
- Updated
- 19 Jun 2017
Overview
Labio is an open-source printed circuit board by rishabh110493, from the rishabh110493/14-642 repository on GitHub. It is a 2-layer board of 152 × 85 mm with 238 parts on 191 nets, routed with 2,396 tracks and 415 vias.
It is built around the BMP280, L3GD20H and LSM303D, with the SPU0410HR5H-1 among its other parts. Its parts include 71 resistors, 52 capacitors, 31 diodes, 19 connectors and 16 transistors.
Main components
4
BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure Sensors
L3GD20H
LGA-16-40℃~+85℃ 16bit 1uA 2.2V~3.6V Gyroscope SPI、I2C X,Y,Z ±2000dps LGA-16 Accelerometers ROHSSTMicroelectronicsAccelerometers
LSM303D
LGA-16_3x3mmLGA-16_3x3mm SMT ROHSSTMicroelectronicsUncategorised
SPU0410HR5H-1
-MEMS MicrophonesKnowles
README
README.md14-642
Work Done in Embedded Systems as a part of course
Parts
238| Qty | Value | Footprint | References |
|---|---|---|---|
| 23 | 0.1uF | Capacitors_SMD:C_0603 | C201, C202, C301, C502, C503, C504, C506, C510, C511, C601, C602, C605, C606, C607, C701, C703 +7 |
| 19 | 220 | Resistors_SMD:R_0603 | R302, R501, R605, R606, R607, R612, R613, R618, R619, R622, R623, R624, R626, R627, R630, R631 +3 |
| 19 | Led_Small | LEDs:LED-0603 | D301, D501, D601, D602, D603, D604, D605, D606, D607, D608, D609, D610, D614, D615, D616, D617 +3 |
| 15 | 20k | Resistors_SMD:R_0603 | R603, R604, R608, R609, R610, R611, R616, R617, R620, R621, R625, R628, R629, R632, R633 |
| 15 | Q_NMOS_GSD | TO_SOT_Packages_SMD:SOT-23 | Q302, Q303, Q601, Q602, Q603, Q604, Q605, Q606, Q607, Q608, Q609, Q610, Q611, Q612, Q613 |
| 13 | 0 | Resistors_SMD:R_0603 | R401, R402, R403, R502, R504, R506, R507, R508, R509, R510, R511, R513, R515 |
| 12 | D_Small | Diodes_SMD:SOD-523 | D611, D612, D613, D618, D619, D620, D621, D622, D623, D624, D625, D626 |
| 11 | 4.7uF | Capacitors_SMD:C_0805 | C401, C501, C505, C507, C508, C509, C702, C706, C712, C716, C718 |
| 10 | DIP_SWITCH_X04 | labio-special:DIP-8_W7.62mm_SMT | SW301, SW401, SW501, SW601, SW602, SW603, SW604, SW606, SW701, SW702 |
| 9 | hole | labio-special:hole-m3 | H1001, H1002, H1003, H1004, H1005, H1006, H1007, H1008, H1009 |
| 7 | 10k | Resistors_SMD:R_0603 | R303, R304, R601, R602, R704, R705, R706 |
| 7 | CONN_01X04 | Pin_Headers:Pin_Header_Straight_1x04 | P301, P302, P303, P603, P701, P702, P703 |
| 7 | F_Small | Resistors_SMD:R_1206 | F301, F401, F501, F602, F603, F604, F701 |
| 5 | SW_PUSH | Buttons_Switches_SMD:SW_SPST_EVPBF | SW801, SW802, SW803, SW804, SW805 |
| 5 | dnp | Capacitors_SMD:C_0603 | C801, C802, C803, C804, C805 |
| 5 | dnp-0 | Resistors_SMD:R_0603 | R404, R406, R503, R512, R514 |
| 4 | 1uF | Capacitors_SMD:C_0603 | C704, C711, C719, C720 |
| 4 | 2.2k | Resistors_SMD:R_0603 | R201, R202, R301, R703 |
| 4 | 47uF | Capacitors_SMD:c_elec_6.3x5.8 | C603, C604, C608, C609 |
| 3 | CONN_01X02 | labio-special:Pin_Header_Straight_1x02_Pitch3.5mm | P601, P602, P604 |
| 2 | 0.01 | Resistors_SMD:R_1206 | R614, R615 |
| 2 | 220uF | Capacitors_SMD:C_1210 | C714, C715 |
| 2 | 47k | Resistors_SMD:R_0603 | R405, R702 |
| 2 | CONN_01X03 | Pin_Headers:Pin_Header_Straight_1x03 | P605, P606 |
| 2 | CONN_01X05 | Pin_Headers:Pin_Header_Straight_1x05 | P607, P608 |
| 2 | TEST_1P | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | W201, W202 |
| 2 | dnp-3.9k | Resistors_SMD:R_0603 | R204, R205 |
| 1 | 0.01uF-25V | Capacitors_SMD:C_0603 | C512 |
| 1 | 0.22uF | Capacitors_SMD:C_0603 | C513 |
| 1 | 220pF | Capacitors_SMD:C_0603 | C709 |
| 1 | 820k | Resistors_SMD:R_0603 | R707 |
| 1 | ADS1015 | Housings_SSOP:MSOP-10_3x3mm_Pitch0.5mm | U301 |
| 1 | AP7365_SOT-23-5 | TO_SOT_Packages_SMD:SOT-23-5 | U201 |
| 1 | BMP280 | labio-special:LGA-8_2.5x2.0mm_Pitch0.65mm_BMx280 | U502 |
| 1 | CMU_LOGO | labio-special:cmu_logo_fsilk_3.7mm | G1 |
| 1 | CMU_LOGO | labio-special:cmu_logo_fcu_3.7mm | G3 |
| 1 | CONN_01X02 | Pin_Headers:Pin_Header_Straight_1x02 | P704 |
| 1 | CONN_01X06 | Pin_Headers:Pin_Header_Angled_1x06 | P901 |
| 1 | CONN_02X20 | labio-special:Pin_Header_Straight_TH-SMT-NoPaste_2x20 | P201 |
| 1 | F_Small | labio-special:OMNI-BLOCK_Fuse_10x5mm_Littelfuse | F601 |
| 1 | JACK_TRRS_6PINS | labio-special:3.5mm-Jack-CUI-SJ-4351X | J701 |
| 1 | L298P_PowerSO20 | labio-special:PowerSO20 | U601 |
| 1 | L3GD20H | labio-special:LGA-16_3x3mm_Pitch0.5mm_ST | U503 |
| 1 | LSM303D | labio-special:LGA-16_3x3mm_Pitch0.5mm_ST | U501 |
| 1 | OPA344_SOT23-5 | TO_SOT_Packages_SMD:SOT-23-5 | U703 |
| 1 | PHOTOTRANSISTOR | LEDs:LED-0603 | Q301 |
| 1 | ROT_ENC | labio-special:Rot-Enc-12mm-Horiz-Button | SW605 |
| 1 | SFV12R-1ST__HLF | labio-special:SFVxxR-xSTxxHLF | P401 |
| 1 | SPU0410HR5H | labio-special:SPU0410HR5H | U701 |
| 1 | WISE_LOGO | labio-special:wise_logo_fsilk_2.5mm | G2 |
| 1 | WISE_LOGO | labio-special:wise_logo_fcu_2.5mm | G4 |
| 1 | WM8750 | labio-special:QFN-32-1EP_5x5mm_Pitch0.5mm | U702 |
| 1 | dnp-10k | Resistors_SMD:R_0603 | R203 |
| 1 | dnp-AT24CS32-XHM | Housings_SSOP:TSSOP-8_4.4x3mm_Pitch0.65mm | IC201 |
More from rishabh110493/14-642
1Similar boards
- 6 layers70 × 40.5 mm
FMUv246-imported
yagamy4680/drone-study
AUAV-OpenSource/FMUv4-PixRacer is the open hardware design of PixHawk FMUv4. It uses STM32F427 and MPU6000. (github)
290 parts - 6 layers70 × 40.5 mm
PX4FMUv2.4
lachlanA/eagle-to-kicad
Eagle SCH/LIB to KiCad SCH/LIB ULP conversion script
354 parts429GPL-2.0 - 4 layers20.3 × 47.5 mm
Rocket ejection
jonnydyer/rocket_ejection
Telemetry recorder and ejection driver for model rockets
52 parts - 2 layers98.6 × 49.8 mm
Sch
SL-RU/svelotracker
Device for bicycle. It will show current position, track, speed, compass, direction to the destination or to start. It can save the track and etc
106 parts1 - 4 layers70.7 × 55.5 mm
Oversoon
malikhubb/Oversoon
Custom PCB design for geolocation sensing, wifi communications, and LED display
64 parts - 2 layers58 × 37 mm
Vibrator Leather Belt control Box
ttempe/Vibrator_Belt
An electronic belt which gives you the north through vibrations
39 parts1 - 2 layers58 × 84 mm
- 4 layers81.1 × 85 mm
STS1 EDU V3 0
SpaceTeam/STS1_EDU_Hardware
Contains all Hardware Informations from EDU 2.6 onwards
108 parts2
Questions
How big is the Labio PCB?
It measures 152 × 85 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Labio use?
238 parts, built around the BMP280, L3GD20H, LSM303D and SPU0410HR5H-1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Labio KiCad files?
From the rishabh110493/14-642 repository on GitHub, at the commit this page was made from: the board is pcb/ioboard/v1.2/labio.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Labio design in my own project?
Its repository states no licence, so its author keeps all rights: ask rishabh110493 before reusing the design.