

Class D Amplifier
- Size
- 73.2 × 67.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 37
- Pads
- 116
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 7 (file 20221018)
- Created
- 2 Nov 2023
- Updated
- 1 Feb 2025
Overview
Class D Amplifier is an open-source printed circuit board by rifky-af, from the rifky-af/pcb-design repository on GitHub, published under the MIT licence. It is a 2-layer board of 73.2 × 67.1 mm with 34 parts on 37 nets.
It is built around the IR2113S, 74HC04D and LM393D, with the IRLIZ44N and SJ2-3573A2-SMT-TR among its other parts. Its parts include 8 capacitors, 6 resistors, 6 ICs, 3 diodes and 3 connectors. It belongs with the audio and music boards of this library.
Main components
5IR2113S
SOIC16WHigh And Low Side DriverInfineon TechnologiesUncategorised74HC04D
SOP-14-40℃~+125℃ 1 1.5V~4.2V 1.9V、3.7V、5.2V 100mV、400mV、400mV 14ns@6V,50pF 2V~6V 2uA 5.2mA 5.2mA 500mV~1.8V 6 74HC SOIC-14 Inverters ROHSNexperiaInvertersLM393D
SOIC-8-18V~-1V、1V~18V 0℃~+70℃ 1.3us 2 25nA 2V~36V 300ns 36V 400uA 5mV 5nA ESD protection TTL、CMOS SOIC-8 Comparators ROHSonsemiComparatorsIRLIZ44N
TO-220-FP1 N-channel 1.7nF@25V 22mΩ@17A,10V 2V@250uA 30A 48nC@5V 55V TO-220-FP MOSFETsInfineon TechnologiesMOSFETsSJ2-3573A2-SMT-TR
--25℃~+85℃ 12V 1A Copper Alloy Silver - Audio Connectors ROHSCUIAudio Connectors (Headphones)
README
README.mdpcb-design
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5_ISO7380_Pad_TopBottom | H1, H2, H3, H4 |
| 3 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R4 |
| 3 | 1N4007 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2, D3 |
| 3 | 47uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C2, C3, C6 |
| 2 | 10 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5, R6 |
| 2 | 1nF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1, C5 |
| 2 | IRLIZ44N | Package_TO_SOT_THT:TO-220F-3_Vertical | Q1, Q2 |
| 2 | Power Terminal | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J2, J3 |
| 1 | 1.1nF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C8 |
| 1 | 10K | Potentiometer_THT:Potentiometer_Bourns_3386C_Horizontal | RV1 |
| 1 | 16.5H | Inductor_THT:L_Radial_D6.0mm_P4.00mm | L1 |
| 1 | 220nF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C4 |
| 1 | 22uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C7 |
| 1 | 2K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 74HC04D | Custom_Library:SOIC127P600X175-14N | U5 |
| 1 | IR2113 | Package_DIP:DIP-14_W7.62mm | U4 |
| 1 | LM393D | Custom_Library:SOIC127P599X175-8N | U1 |
| 1 | LM7805_TO220 | Package_TO_SOT_THT:TO-220-3_Vertical | U3 |
| 1 | LM7812_TO220 | Package_TO_SOT_THT:TO-220-3_Vertical | U6 |
| 1 | SJ2-3573A2-SMT-TR | Custom_Library:CUI_SJ2-3573A2-SMT-TR | J1 |
| 1 | TLC555xP | Package_DIP:DIP-8_W7.62mm | U2 |
More from rifky-af/pcb-design
7- 2 layers40 × 31 mm

- 2 layers95 × 66 mm

- 2 layers61 × 25.4 mm

- 2 layers39 × 25 mm

- 2 layers68.6 × 22.9 mm

- 2 layers58 × 58 mm

- 2 layers53.3 × 25.4 mm

Similar boards
- 4 layers190 × 91 mm

Inv v1
reljamar/singlePhaseInverter
A precursor project to a future three-phase inverter for driving synchronous motors
160 parts1MIT - 2 layers107.2 × 60.3 mm

Class D Audio Amplifier
fredie1811/Class-D-Amplifier
The KiCad Schematic and PCB Layout for a Half Bridge Class-D Audio Amplifier using an MH-M28 for inputting the audio via an audio jack or via bluetooth.
35 parts - 4 layers32.8 × 36.3 mm

Esp32
gdoor-org/gdoor
Wifi adapter and bus protocol documentation for the Gira TKS Door System
68 parts57GPL-3.0 - 2 layers177 × 91.6 mm

Power Charg AUTO 12V C
Aleksei327/STM32G474-Power-Charger
Experimental STM32G474-based high-current battery charger and programmable synchronous buck converter. KiCad hardware and STM32CubeIDE firmware.
160 parts3 - 2 layers65.4 × 29 mm

Final project no connector
Laurenx618/ENGR3430-Eclectronics-FinalProject
This project is for the Eclectronics Final.
69 parts2 - 2 layers183.5 × 133 mm

- 2 layers74.9 × 59.7 mm

EMS BUS
JakobThiessen/SmartHome_EMS-BUS-WI-FI-GATEWAY
ESP32-EMS WiFi gateway for read and control EMS and Heatronic compatible devices such as boilers, thermostats, solar modules and heat pumps.
51 parts1 - 4 layers44 × 22 mm

Doublebridgeright v8
supernova-10/Kubits-programmable-magnets
Kubit is my Final Year Project (FYP) — a modular reconfigurable robot that uses programmable magnets, gears, and custom PCB-based control to achieve untethered actuation and reconfiguration.
32 parts1
Questions
How big is the Class D Amplifier PCB?
It measures 73.2 × 67.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Class D Amplifier use?
34 parts, built around the IR2113S, 74HC04D, LM393D and IRLIZ44N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Class D Amplifier KiCad files?
From the rifky-af/pcb-design repository on GitHub, at the commit this page was made from: the board is Class D Amplifier/Class D Amplifier.kicad_pcb and its schematic Atiny85_USB/Atiny85_USB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Class D Amplifier design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).