

W25Q BRD
W25Q-BRD is a breakout board for DIY use
- Size
- 16 × 23 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 10
- Nets
- 10
- Pads
- 50
- Tracks, vias
- 55, 23
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 9 Dec 2022
- Updated
- 12 Jul 2023
Overview
W25Q BRD is an open-source printed circuit board by red-scorp, from the red-scorp/W25Q-BRD repository on GitHub. It is a 2-layer board of 16 × 23 mm with 10 parts on 10 nets, routed with 55 tracks and 23 vias.
It is built around the W25Q128JVPIQ and W25Q128JVSIQ. Its parts include 2 capacitors, 2 resistors, 2 ICs, 2 diodes and 1 connector. It belongs with the interfaces and adapters and microcontroller boards boards of this library.
Main components
2W25Q128JVPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 120ms@(32KB) 128Mbit 133MHz 2.7V~3.6V 20 Years Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbond ElecNOR FLASHW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
README
README.mdW25Q-BRD project
W25Q-BRD project is meant to provide people with cheap SPI flash breakout board.
W25Q-BRD
W25Q-BRD is a breakout board for DIY use. This board features 128Mbit (16MB) serial flash chip W25Q128JVSIQ and M3 mounting hole. The flash board runs on 3.3V and supports SPI and QSPI transfer modes.
Preview:

Features:
- Uses 3.3V voltage
- Runs in SPI and QSPI modes
- Simple 2 layer board design
- Common for DIY 2.54mm pitch connector
- Features SIOC-8 and WSON-8(6x5) footprints
CAM files are available. JLCPCB BOM and CPL files are available.
W25Q-BRD v1.0
Preview:

Initial version of the board.
W25Q-BRD v1.1
Preview:

Added capacitors for better voltage stability.
W25Q-BRD v1.2
Preview:

Added alternative WSON footprint to add more fabrication options.
Board pinout
| Pin | SPI mode | QSPI mode |
|---|---|---|
| 3V3 | VCC of the chip, 3.3V | |
| NCS | Chip select signal | |
| IO0 | Data input | Data IO 0 |
| IO1 | Data output | Data IO 1 |
| IO2 | - | Data IO 2 |
| IO3 | - | Data IO 3 |
| CLK | (Q)SPI clock signal | |
| GND | Ground | |
Links
- Flash chip W25Q128JVSIQ datasheet
How to help
Your contributions as code, resources, or finances are welcome! Please contact me directly via email at andriy.golovnya@gmail.com or through my GitHub profile.
If you'd like to make a financial contribution, you can donate via PayPal or Ko-Fi. Your support is greatly appreciated.
Thanks in advance!
Parts
10| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 5k1 | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1 |
| 1 | QSPI | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | W25Q128JVPIQ | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U2 |
| 1 | W25Q128JVSIQ | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U1 |
Similar boards
- 2 layers269.9 × 93.1 mm

- 2 layers29.8 × 40.6 mm

- 4 layers53.5 × 49.5 mm

- 2 layers290.1 × 130 mm

- 6 layers66 × 66 mm

PD240W kicad
theohg/PD240W
PD240W is a complete hardware and firmware project converting USB-C Power Delivery into a programmable 240W (48V 5A) bench power supply, featuring C++ code for Raspberry Pi Pico, custom PCB Gerbers, and a 3D-printable…
299 parts125 - 4 layers51 × 21 mm

Hardware Arctyx Nano
Keyaan-07/Arctyx-Nano
An open-source FPGA development board in RaspberryPi Pico form factor.
71 parts124MIT - 4 layers114 × 87.7 mm

- 6 layers56 × 65 mm

Mainboard gen2
zephray/NekoInk
Next gen. of NekoCal: An open-source hackable and programmable e-paper display
245 parts108
Questions
How big is the W25Q BRD PCB?
It measures 16 × 23 mm and has 2 copper layers, 1.6 mm thick.
What parts does the W25Q BRD use?
10 parts, built around the W25Q128JVPIQ and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the W25Q BRD KiCad files?
From the red-scorp/W25Q-BRD repository on GitHub, at the commit this page was made from: the board is W25Q-BRD.kicad_pcb and its schematic W25Q-BRD.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the W25Q BRD design in my own project?
Its repository states no licence, so its author keeps all rights: ask red-scorp before reusing the design.