

Arquitetura de processador conceitual
- Size
- 160.7 × 210 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 124
- Nets
- 234
- Pads
- 908
- Tracks, vias
- 2,635, 213
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 11 Dec 2025
- Updated
- 24 Aug 2026
Overview
Clu is an open-source printed circuit board by rcapaverde, from the rcapaverde/cubo repository on GitHub. It is a 2-layer board of 160.7 × 210 mm with 124 parts on 234 nets, routed with 2,635 tracks and 213 vias.
It is built around the 74LS125DC, 74LS32SC and 74LS157PC, with the 74LS574N, 74LS74PC and 74LS86 among its other parts. Its parts include 35 ICs, 33 capacitors, 33 connectors, 10 diodes and 3 switches.
Main components
974LS125DC
-0℃~+70℃ 1 10ns@5.5V,50pF 15mA 18mA 24mA 4 4.5V~5.5V 74LS Power-off isolation、Output enable Tri-State Unidirectional - Buffers, Drivers, Receivers, TransceiversTexas InstrumentsBuffers, Drivers, Receivers, Transceivers74LS32SC
-- Logic Gates ROHSTexas InstrumentsLogic Gates74LS157PC
PDIP-160℃~+70℃ 4.75V~5.25V Single Supply PDIP-16 Signal Switches, Multiplexers, Decoders ROHSTexas InstrumentsSignal Switches, Multiplexers, Decoders74LS574N
-0ns 0℃~+70℃ 1 2.6mA 20ns 24mA 28ns@5V,45pF 35MHz 4.75V~5.25V 74LS Series 8 D-Type Rising Edge Tri-State - Flip Flops ROHSRochester Electronics, LLCFlip Flops74LS74PC
DIP-140ns 0℃~+70℃ 1 2 20MHz 3.5pF 35ns@5V,50pF 4.5ns 4.75V~5.25V 400uA 74LS Series 8mA 8mA Asynchronous Complementary D-Type Rising Edge Set and Reset DIP-14 Flip FlopsTexas InstrumentsFlip Flops74LS86
DIP-14-20℃~+75℃ 10mA 2.7V 23ns@5V,15pF 2V 400mV 400uA 5V 74LS 800mV 8mA XOR Gate DIP-14 Logic Gates ROHSHITLogic Gates74LS02PC
DIP-140℃~+70℃ 15ns@5V,15pF 2 2.7V 2V 4 4.75V~5.25V 400uA 500mV 74LS 800mV 8mA 8mA NOR Gate DIP-14 Logic Gates ROHSonsemiLogic Gates74LS04PC
PDIP-140℃~+70℃ 4.75V~5.25V 6 6.6mA 74LS PDIP-14 InvertersonsemiInverters74LS193P-E
DIP-1674LS Programmable divide ratio、Reset function、Cascade counter、Synchronous counting、Multi-mode counting DIP-16 Counters, Dividers ROHSRenesas ElectronicsCounters, Dividers
README
README.mdcubo - um processador conceitual
Parts
124| Qty | Value | Footprint | References |
|---|---|---|---|
| 33 | 100nF | Capacitor_THT:C_Disc_D5.1mm_W3.2mm_P5.00mm | C1, C2, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 +17 |
| 20 | Conn_01x07 | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J10, J11, J13, J14, J16, J17, J19, J20, J22, J23, J25, J26, J28, J29, J30, J31 +4 |
| 10 | 74LS32 | Package_DIP:DIP-14_W7.62mm | U5, U14, U18, U21, U22, U23, U26, U33, U34, U35 |
| 10 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7, J9, J12, J15, J18, J21, J24, J27, J32, J33 |
| 5 | 10K | Resistor_THT:R_Array_SIP5 | RN2, RN3, RN4, RN5, RN7 |
| 4 | 74LS157 | Package_DIP:DIP-16_W7.62mm | U3, U6, U7, U17 |
| 3 | 74LS138 | Package_DIP:DIP-16_W7.62mm | U2, U30, U32 |
| 2 | 1K | Resistor_THT:R_Array_SIP6 | RN8, RN9 |
| 2 | 74LS08 | Package_DIP:DIP-14_W7.62mm | U20, U27 |
| 2 | 74LS244 | Package_DIP:DIP-20_W7.62mm | U13, U15 |
| 2 | 74LS574 | Package_DIP:DIP-20_W7.62mm | U8, U12 |
| 2 | 74LS74 | Package_DIP:DIP-14_W7.62mm | U28, U29 |
| 2 | 74LS86 | Package_DIP:DIP-14_W7.62mm | U16, U24 |
| 2 | MC14495P | Package_DIP:DIP-16_W7.62mm | U10, U31 |
| 1 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R12 |
| 1 | 10K | Resistor_THT:R_Array_SIP9 | RN1 |
| 1 | 10K | Resistor_THT:R_Array_SIP6 | RN6 |
| 1 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D5 |
| 1 | 74LS02 | Package_DIP:DIP-14_W7.62mm | U4 |
| 1 | 74LS04 | Package_DIP:DIP-14_W7.62mm | U19 |
| 1 | 74LS125 | Package_DIP:DIP-14_W7.62mm | U25 |
| 1 | 74LS193 | Package_DIP:DIP-16_W7.62mm | U1 |
| 1 | FETCH | LED_THT:LED_D5.0mm | D2 |
| 1 | HALT | LED_THT:LED_D5.0mm | D6 |
| 1 | HIGH | LED_THT:LED_D5.0mm | D14 |
| 1 | IREQ | LED_THT:LED_D5.0mm | D25 |
| 1 | IR_HIGH | Display_7Segment:Sx39-1xxxxx | U11 |
| 1 | IR_LOW | Display_7Segment:Sx39-1xxxxx | U9 |
| 1 | LOW | LED_THT:LED_D5.0mm | D13 |
| 1 | POWER | LED_THT:LED_D5.0mm | D1 |
| 1 | SW_DIP_mem_pc | Button_Switch_THT:SW_DIP_SPSTx04_Slide_6.7x11.72mm_W7.62mm_P2.54mm_LowProfile | SW3 |
| 1 | SW_DIP_pc | Button_Switch_THT:SW_DIP_SPSTx04_Slide_6.7x11.72mm_W7.62mm_P2.54mm_LowProfile | SW6 |
| 1 | SW_DIP_read_mem_const | Button_Switch_THT:SW_DIP_SPSTx04_Slide_6.7x11.72mm_W7.62mm_P2.54mm_LowProfile | SW1 |
| 1 | TRUE | LED_THT:LED_D5.0mm | D24 |
| 1 | ULA | LED_THT:LED_D5.0mm | D4 |
| 1 | WRITE | LED_THT:LED_D5.0mm | D3 |
| 1 | bus clu 1 | edge_connector:conector 02x08 | J1 |
| 1 | bus clu 2 | edge_connector:conector 02x08 | J2 |
| 1 | bus clu 3 | edge_connector:conector 02x08 | J3 |
More from rcapaverde/cubo
12- 2 layers120.6 × 47 mm

- 2 layers137.8 × 73.6 mm

- 2 layers297 × 125 mm

- 2 layers160.7 × 210 mm

- 2 layers

- 2 layers126.3 × 210 mm

- 2 layers

- 2 layers274.3 × 124.5 mm

- 2 layers297 × 75 mm

- 2 layers77.5 × 125 mm

- 2 layers209.5 × 125.1 mm

- 2 layers209.5 × 125.1 mm

Similar boards
- 4 layers304.5 × 217.2 mm

Latest Full Backplane
Trilobyte-CPU/8-bit-computer
A DIY 8-bit computer built mostly with discrete logic chips
478 parts2 - 2 layers486 × 306.3 mm

- 2 layers630 × 300 mm

- 2 layers221.5 × 149.5 mm

ZX1
misterblack1/zenith_zt1
Information gathered on the Zenith ZT-1 / ZT-10 / ZT-11 and ZTX/ZT-x-A variants
140 parts5 - 4 layers298.9 × 270 mm

Dino v0 0 2
robertrico/dino-homebrew
A perfboard with the bus edge and the slot decode every DINO card repeats. Plug it into any of J1-J8 on the Rev 1.0 mainboard, pick the slot with one shunt, bodge the card on the grid.
239 parts - 2 layers301.5 × 367.3 mm

OSI 600D Superboard II Cherry Solder Mask
Bambelweeny57/OSI-600D-SuperBoard-II
KiCad 10 recreation of the Ohio Scientific Superboard II Model 600 rev D (1980) with Cherry MX keyswitches, 27C16/2816 ROMs, full schematic and assembly guide.
314 parts - 2 layers199.6 × 74.2 mm

- 4 layers337.6 × 105.7 mm

ISA CGA
hkzlab/CGA_Redux
The Color Graphics Adapter Redux board is a more or less faithful clone of the original IBM CGA, based on the original schematics
170 parts56
Questions
How big is the Clu PCB?
It measures 160.7 × 210 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Clu use?
124 parts, built around the 74LS125DC, 74LS32SC, 74LS157PC and 74LS574N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Clu KiCad files?
From the rcapaverde/cubo repository on GitHub, at the commit this page was made from: the board is pcb_v3/clu/clu.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Clu design in my own project?
Its repository states no licence, so its author keeps all rights: ask rcapaverde before reusing the design.