4 layers84 × 52 mm
Sideline cam hub
dawsboss/Sports-Camera-Analytics-
Input a video of your game and out pops the all player positioning data you want. for I put into Minutes
102 parts
4 layers65 × 56 mm
RPi OLED Adapter
RasmusB/RPi-OLEDAdapter board for using a generic OLED with a Raspberry Pi
- Size
- 65 × 56 mm
- Copper layers
- 4
- Thickness
- 1.04 mm
- Parts
- 35
- Nets
- 69
- Pads
- 185
- Tracks, vias
- 696, 144
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 17 Sep 2026
- Updated
- 11 Oct 2026
Overview
RPi OLED Adapter is an open-source printed circuit board by RasmusB, from the RasmusB/RPi-OLED repository on GitHub. It is a 4-layer board of 65 × 56 mm with 35 parts on 69 nets, routed with 696 tracks and 144 vias.
It is built around the CAT24C256WI-GT3, TCA9800DGK and TPS22917DBV, with the TPS76318DBVR-TP, FH12-22S-0.5SH(55) and FH26W-39S-0.3SHW(60) among its other parts. Its parts include 8 resistors, 7 capacitors, 4 ICs and 3 connectors. It belongs with the lEDs and displays and interfaces and adapters boards of this library.
Main components
6
CAT24C256WI-GT3
SOIC-8-40℃~+85℃ 1,000,000 cycles 1.8V~5.5V 100 Years 1MHz 256Kbit 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOIC-8 EEPROM ROHSonsemiEEPROM
TCA9800DGK
VSSOP-8-0.65mm-40℃~+125℃ 1 1.65V~3.6V 2 800mV~3.6V Auto Direction Detection、Power-Off Protection Bidirectional VSSOP-8-0.65mm Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
TPS22917DBV
SOT-23-6-40℃~+125℃ 0V~5.5V 1 2A 80mΩ Active High Load Switch Output discharge function、Soft-start、Reverse current blocking SOT-23-6 Power Distribution Switches ROHSTexas InstrumentsPower Distribution Switches
TPS76318DBVR-TP
SOT-23-5-40℃~+125℃@(Tj) 1 1.8V 12V 150mA 2uA 500mV@(100mA) 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
FH12-22S-0.5SH(55)
SMDSMD Pre-ordered Connectors ROHSHirose ElectricFFC, FPC (Flat Flexible) Connector Assemblies
FH26W-39S-0.3SHW(60)
SMD,P=0.3mm,卧贴-55℃~+85℃ 0.2mm 0.3mm 1mm 39P Bottom Contact Gold Hinged Lid Phosphor bronze Surface Mount, Right Angle SMD,P=0.3mm,卧贴 FFC, FPC (Flat Flexible) Connector Assemblies ROHSHirose ElectricFFC, FPC (Flat Flexible) Connector Assemblies
README
README.mdRPi-OLED Readme
Adapter board for using a generic OLED with a Raspberry Pi
[!WARNING] Before using this repo, make sure to run the 'setup-hooks.sh' script first.
Release notes
Releases are tagged using custom Semantic Versioning rules.
0.1.0
- TODO: List features that are introduced / removed
- Focus on changes that would affect the end user, and indicate how they will be affected.
- For example, don't write 'R2 changed to pull-down', but instead: 'Board will enter the bootloader when the user pushes SW1'.
- More detailed change notes goes into the version history table in the schematic.
Git behaviour
There are some pre-commit hooks in the .git folder. These will attempt to enforce a few sanity rules based on the following rules.
The main branch must only contain releases of production files
- Commits to
mainare not allowed - TODO: Commits must be tagged to generate production files (at least on the main branch)
- TODO: Tags must follow the pattern
vX.Y.Z(see the SemVer rules for details)
Development happens in a dev branch
- All check-ins during development are made on the
devbranch. Thedevbranch is merged intomainwhen (and only when) the production files are ready for release. - Any tags created on the dev branch must not match the pattern
vX.Y.Zto ensure they are not confused for proper release tags - Merging to main is not allowed if there are any failing tests (ERC, DRC, etc.)
Parts
35| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7 |
| 4 | 3.9k | Resistor_SMD:R_0402_1005Metric | R1, R2, R7, R8 |
| 4 | MountingHole_2.7mm_M2.5 | MountingHole:MountingHole_2.7mm_M2.5 | MH1, MH2, MH3, MH4 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R3, R5 |
| 2 | 12k1 | Resistor_SMD:R_0402_1005Metric | R4, R6 |
| 1 | 0x50/(51) | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP2 |
| 1 | 1V8_EN | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | NT4 |
| 1 | 1V8_MEAS | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | NT6 |
| 1 | 3V3_EN | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | NT2 |
| 1 | 3V3_MEAS | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | NT5 |
| 1 | 5V_MEAS | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | NT7 |
| 1 | CAT24C256 | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U1 |
| 1 | DSI IN | Connector_FFC-FPC:Hirose_FH12-22S-0.5SH_1x22-1MP_P0.50mm_Horizontal | J2 |
| 1 | GPIO | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1 |
| 1 | ID_WP | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1 |
| 1 | OLED_H497TLB01 | Connector_FFC-FPC:Hirose_FH26-39S-0.3SHW_2Rows-39Pins-1MP_P0.60mm_Horizontal | J9 |
| 1 | OLED_TE | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | NT1 |
| 1 | TCA9800 | Package_SO:VSSOP-8_3x3mm_P0.65mm | U2 |
| 1 | TPS22917DBV | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | TPS76318 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | ~{TP_INT} | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | NT3 |
Questions
How big is the RPi OLED Adapter PCB?
It measures 65 × 56 mm and has 4 copper layers, 1.04 mm thick.
What parts does the RPi OLED Adapter use?
35 parts, built around the CAT24C256WI-GT3, TCA9800DGK, TPS22917DBV and TPS76318DBVR-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RPi OLED Adapter KiCad files?
From the RasmusB/RPi-OLED repository on GitHub, at the commit this page was made from: the board is RPi-OLED-Adapter.kicad_pcb and its schematic RPi-OLED-Adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the RPi OLED Adapter design in my own project?
Its repository states no licence, so its author keeps all rights: ask RasmusB before reusing the design.
Similar boards
- 4 layers100 × 100 mm
Data logger
Conor-Dunlop/FYP_datalogger
render of the datalogger with power board (yes i know it need routed)
176 parts - 2 layers40 × 38.5 mm
- 4 layers100 × 62.5 mm
Omniframe Hardware
omniframe-art/Omniframe-Hardware
Omniframe is an open source e-paper digital frame. This repository includes the source and fabrication files for the main and secondary boards for driving the 13.3" Monochrome e-ink display.
104 parts4 - 2 layers80 × 60 mm
IRIS C5 RevC
Benv-B/photo-frame-hardware
Open hardware carrier for an AirDrop ChLCD color e-paper frame: XIAO ESP32-C5, NFC wake, KiCad, schematic, BOM and Gerbers. CERN-OHL-P-2.0.
66 partsCERN-OHL-P-2.0 - 4 layers32 × 50 mm
- 4 layers32 × 26 mm
Neurband main
jlcjak/neurband
Open, minimal sEMG wristband like the Meta Neural Band: 8-ch ADS1298 + nRF52832 BLE, dry gold electrodes on a flex, 3D-printed band. KiCad, FreeCAD, Zephyr, Python, simulations.
60 parts46 - 2 layers26.6 × 17.9 mm
Adapter
pdyxs/glider
Fork of zephray/glider (Modos Glider e-ink monitor) with a DP AUX polarity fix and a standalone GCC firmware build
2 partsCERN-OHL-S-2.0