Skip to the content
4 layers100 × 80.1 mmPace core, the printed circuit board in 3D

Kicad Hardware files and docs for the PACE V0 board (RACER)

Size
100 × 80.1 mm
Copper layers
4
Thickness
1.57 mm
Parts
175
Nets
101
Pads
533
Tracks, vias
1,065, 685
Pours
364
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
3 Jun 2026
Updated
5 Oct 2026

Overview

Pace core is an open-source printed circuit board by rammp-org, from the rammp-org/pace-racer-hardware repository on GitHub. It is a 4-layer board of 100 × 80.1 mm with 175 parts on 101 nets, routed with 1,065 tracks and 685 vias.

It is built around the ESP32-S3-WROOM-1-N16R2, DRV8353SRTAT and SM06B-SRSS-TB(LF)(SN), with the ADUM3160BRWZ-RL, AMS1117-3.3 and ISC0802NLSATMA1 among its other parts. Its parts include 40 capacitors, 40 resistors, 10 ICs, 7 connectors and 6 transistors. It belongs with the ESP32 boards of this library.

Main components

11

README

README.md

PACE Racer motor controller (KiCad hardware)

Welcome to the official hardware repository for the PACE V0 (RACER) motor controller board. This repository contains all KiCad design schematics, layout files, and hardware documentation required to manufacture, test, and interface with the RACER platform. The companion firmware for this board is under active development in the companion repository: pace-racer-firmware.

How this repo works: humans commit KiCad sources; CI (KiBot) runs ERC and DRC on every PR and builds gerbers, BOM, position, ibom, PDFs, STEP and renders. Tagging VnRm publishes those as a GitHub Release. See docs/style-guide.md for conventions and docs/decisions/ for the why behind unusual choices.

PaceRacerV0R1 Splash2

Documentation & Resources

Access the schematics and an interactive board viewer here!

Access Interactive KiCanvas Board Viewer & Schematics ---

Hardware Architecture Overview

The PACE V0 (RACER) is a high-performance, intelligent 3-phase inverter platform powered by an ESP32-S3. It is engineered to support both high-frequency Field-Oriented Control (FOC) and traditional Trapezoidal (Block) Commutation strategies.

mermaid
flowchart TD
    %% Upstream USB Environment
    subgraph Upstream ["Upstream Side (Isolated USB Environment)"]
        USB["USB-C Connector<br>(USB1)"] -->|VBUS / GND_USB| VUSB["+5V-USB Rail<br>& GND-USB Rail"]
        VUSB -->|Powers Upstream Side| ISO_In["ADUM3160 Digital Isolator<br>(U4 Upstream Pins)"]
    end

    %% Galvanic Isolation Barrier
    subgraph Barrier ["Galvanic Isolation Boundary"]
        ISO_In -.->|Optical/Magnetic Data Isolation| ISO_Out["ADUM3160 Digital Isolator<br>(U4 Downstream Pins)"]
        SW3{"SW3 Switch<br>(DPDT)"}
    end

    %% High Voltage Input Power Stage
    subgraph HV_Stage ["High-Voltage Input Power Stage"]
        BATT["+BATT Input Rail<br>(48V Nominal Target)"] --> Caps["DC-Link Capacitor Buffers<br>(100V Continuous Rating Limit)"]
        Caps --> XLBuck["XL7015E1 Buck Converter<br>(U6 Stage)"]
    end

    %% Main Logic Subsystems
    subgraph Logic_Rails ["Downstream Logic & Control Subsystem"]
        XLBuck -->|Step Down| V5["+5V Local Rail"]
        
        V5 -->|Linear Regulation| AMS["AMS1117-3.3 LDO (U5)"]

1. Processing & Inverter Stage

  • Core MCU: An ESP32-S3-WROOM-1 module handles raw motor control mathematics, wireless telemetry, and hardware interrupt management.
  • Gate Driver: A TI DRV8353SRTAT 3-phase gate driver provides independent high-side/low-side drive configurations, hardware fault line triggers, and runtime register adjustments via SPI.
  • Power MOSFETs: 6x ISC0802NLSATMA1 MOSFETs are structured in a traditional 3-phase half-bridge bridge array.
  • Current Sensing: Dual-purpose inline, low-side 1.0 mΩ current sense shunts (R1, R2, R3) are deployed on all three phases to capture fast current waveforms for precision FOC.

2. Sensor Framework

  • Rotor Position Feedback: Supports dual encoder paradigms:
    • High-speed SPI telemetry via the MT6701 Magnetic Rotary Encoder interface.
    • Discrete input lines for standard 3-phase Hall effect sensor elements (hall-a, hall-b, hall-c).
  • Thermal Management: 4x LM75ADP I2C digital temperature monitors are distributed across key thermal zones on a single I2C bus. Fixed hardware addressing assigns them respectively to 0x4C, 0x4D, 0x4E, and 0x4F.

3. Communications & Safety

  • Wired Networking: A Wiznet W5500 Ethernet Coprocessor configuration allows stable, high-throughput network communication over a shared high-speed SPI bus.
  • Galvanic Isolation: The upstream USB-C debugging connection features an ADUM3160BRWZ-RL digital isolation chip to safely separate logic lines from high-voltage battery transient grounds (see docs/decisions/0001-ground-domains.md) during live tuning.

Hardware Pin Mapping Reference

This table is generated from the schematic netlist by tools/gen_readme.py and checked in CI. Do not edit it by hand. Net names follow docs/style-guide.md (lowercase domain-kebab); the firmware hal_pins.h should use these names.

MCU pinNetConnected to
IO0/st-boot (pin 27)mcu-bootR8, SW1
RXD0 (pin 36)uart-rxJ4
TXD0 (pin 37)uart-txJ4
IO1/adc1-0 (pin 39)vref-1v6C23, C27, TP24, U2, U7
IO2/adc1-1 (pin 38)mcu-io2J4
IO3/st-jtag/adc1-2 (pin 15)hall-aC42, R34
IO4/adc1-3 (pin 4)isense-aC30, R10
IO5/adc1-4 (pin 5)isense-bC29, R21
IO6/adc1-5 (pin 6)isense-cC28, R22
IO7/adc1-6 (pin 7)pwm-c-lowR26, U2
IO8/adc1-7 (pin 12)pwm-a-highR31, U2
IO9/adc1-8 (pin 17)hall-cC40, R25
IO10/adc1-9/FSPI-CS (pin 18)eth-spi-csJ2, R23
IO11/FSPI-D (pin 19)spi-copiJ2, U2
IO12/FSPI-CLK (pin 20)spi-clkJ2, U2
IO13/FSPI-Q (pin 21)spi-cipoJ2, R17, U2
IO14 (pin 22)eth-irqJ2
IO15 (pin 8)pwm-c-highR27, U2
IO16 (pin 9)pwm-b-lowR28, U2
IO17 (pin 10)pwm-b-highR29, U2
IO18 (pin 11)pwm-a-lowR30, U2
IO19/USBD- (pin 13)usb-dmU4
IO20/USBD+ (pin 14)usb-dpU4
IO21 (pin 23)eth-resetJ2
IO35 (pin 28)enc-spi-cipoU12
IO36 (pin 29)enc-spi-copiJ4, U12
IO37 (pin 30)enc-spi-clkU12
IO38 (pin 31)enc-spi-csR24, U12
IO39 (pin 32)drv-spi-csU2
IO40 (pin 33)drv-faultR16, U2
IO41 (pin 34)led-greenD2, J4
IO42 (pin 35)led-blueD1, J4
IO45/st-spi-v (pin 26)i2c-sdaJ4, R39, U10, U11, U8, U9
IO46/st-rom (pin 16)hall-bC41, R33
IO47 (pin 24)drv-enableR32, U2
IO48 (pin 25)i2c-sclJ4, R40, U10, U11, U8, U9
EN (pin 3)mcu-resetR9, SW2

Power Distribution & Topology

The RACER PCB layout handles standard heavy industrial current loops alongside sensitive logic rails. Care must be taken during low-level development to understand the distinct ground rules and supply behavior.

  • Main DC Power Stage Input (+BATT): Accepts high-voltage input up to 60V DC. High and low-frequency buffer capacitor banks are placed immediately across each half-bridge phase to suppress heavy inductive switching ripples up to 25MHz.
  • Logic Subsystem Buck (5V Rail): Driven by an XL7015E1 high-voltage buck regulator topology, dropping the high-voltage input down to a common local 5V line.
  • Microcontroller Supply (3.3V Rail): An AMS1117-3.3 linear regulator drops the local 5V line to a stable 3.3V rail dedicated to powering the ESP32-S3 and onboard sensors.
  • Analog Ingestion Bias Reference (vref-1v6): Formed via a REF35160QDBVR high-precision reference generator connected to the 5V line. This outputs a fixed 1.6V reference bias to calibrate the inline current shunt amplifiers, permitting measurement of negative and positive phase currents across the full bi-directional stroke.
  • Isolation Boundary Notice: The 5V-USB rail is strictly limited to powering the upstream digital isolator components. Flipping the physical isolation switch (SW3) cleanly detaches the target ground (GND) from development computer USB shields (GND-USB) to protect computer infrastructure against high-power faults.

First-Stage Firmware Initialization Blueprint

To quickly bring up prototype firmware on pace-racer-firmware, organize your driver initializations using this execution checklist:

Phase 1: Core Systems & Diagnostic Telemetry

  1. Define the physical I/O allocations outlined in the pin reference table.
  2. Initialize diagnostic LEDs (IO41, IO42) to indicate a booting state.
  3. Fire up the shared I2C bus over IO45 and IO48 to loop and register responses from the four LM75ADP temperature sensor configurations at addresses 0x4C through 0x4F.

Phase 2: Inverter Protection & Commutation Interfaces

  1. Configure IO40 (drv-fault) as an active-low hardware interrupt line. Ensure its handler instantly forces all PWM generation lines into a low (disabled) safety state if triggered.
  2. Initialize the main SPI communications bus over pins spi-copi, spi-clk, and spi-cipo. Pull the gate driver chip select (IO39) low to configure the DRV8353 operational state registers.
  3. For Field-Oriented Control (FOC), configure high-speed SPI capture over the encoder subsystem (IO35, IO37, IO38) to decode magnetic orientation data from the MT6701.
  4. For Trapezoidal Commutation, establish change-of-state interrupt routines tracking discrete pin changes across Hall effect inputs (IO3, IO46, IO9).

Phase 3: Ethernet Networking

  1. Cycle the hardware reset pin IO21 to clear the internal registers of the W5500 Ethernet chip.
  2. Configure SPI tracking over the controller chip select pin IO10.
  3. Initialize the raw sockets over network stacks using the standard eth-irq (IO14) interrupt pin to manage incoming and outgoing network interface events without blocking the high-frequency motor control loops.

Parts

175
QtyValueFootprintReferences
2010kResistor_SMD:R_0402_1005MetricR16, R17, R18, R19, R20, R23, R24, R26, R27, R28, R29, R30, R31, R32, R35, R36 +4
6100RResistor_SMD:R_0402_1005MetricR10, R21, R22, R25, R33, R34
61nFCapacitor_SMD:C_0402_1005MetricC28, C29, C30, C40, C41, C42
6ISC0802NLSATMA1specific-parts-lib:PG-TDSON-8_L5.9-W5.1-P1.27-LS6.1-BLQ7, Q8, Q9, Q10, Q11, Q12
6SMTSOM330BTRspecific-parts-lib:M3-TH_BD6.0-D4.3CN2, CN3, CN4, CN5, CN6, CN7
5TestPointTestPoint:TestPoint_Pad_D2.0mmTP18, TP19, TP20, TP24, TP25
40.1uFCapacitor_SMD:C_0402_1005MetricC31, C32, C33, C34
45k1Resistor_SMD:R_0402_1005MetricR4, R5, R8, R9
4LM75ADP,118specific-parts-lib:TSSOP-8_L3.0-W3.0-P0.65-LS4.9-BLU8, U9, U10, U11
4PA100V22M6X9specific-parts-lib:CAP-TH_BD6.3-P2.50-D0.6-FDC36, C37, C38, C39
31.0mΩspecific-parts-lib:RES-SMD_L6.3-W3.1-1R1, R2, R3
3100nFCapacitor_SMD:C_0603_1608MetricC1, C9, C10
310uFCapacitor_SMD:C_0603_1608MetricC4, C18, C23
31uFCapacitor_SMD:C_1206_3216MetricC15, C25, C26
32.2uF 100VCapacitor_SMD:C_1206_3216MetricC6, C7, C8
34.7uF 100VCapacitor_SMD:C_1210_3225MetricC11, C12, C13
3470uF 100Vspecific-parts-lib:CAP-TH_BD16.0-P7.50-D1.2-FDC19, C20, C21
35kResistor_SMD:R_0402_1005MetricR11, R12, R13
3NetTie_2specific-parts-lib:shunt-net-tieNT1, NT2, NT3
20Resistor_SMD:R_0402_1005MetricR6, R7
2SKRPACE010specific-parts-lib:KEY-SMD_4P-L4.2-W3.2-P2.20-LS4.6SW1, SW2
2SM06B-SRSS-TBspecific-parts-lib:CONN-SMD_SM06B-SRSS-TB-LF-SNU12, U13
2SolderJumper_3_Bridged12Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mmJP4, JP5
1.1uFCapacitor_SMD:C_0402_1005MetricC27
1100nFCapacitor_SMD:C_0402_1005MetricC24
1100uF 16vCapacitor_SMD:C_Elec_6.3x7.7C17
1100uH 1Aspecific-parts-lib:IND-SMD_L10.0-W10.0_SRU1038-100YL2
110k 1%Resistor_SMD:R_0402_1005MetricR15
110uFCapacitor_SMD:C_1206_3216MetricC2
12.2uFCapacitor_SMD:C_1210_3225MetricC35
122uFCapacitor_SMD:C_0603_1608MetricC3
130k 1%Resistor_SMD:R_0402_1005MetricR14
133nFCapacitor_SMD:C_0402_1005MetricC16
147nFCapacitor_SMD:C_0603_1608MetricC14
1ADUM3160BRWZ-RLspecific-parts-lib:SOIC-16_L10.3-W7.5-P1.27-LS10.3-BLU4
1AMS1117-3.3specific-parts-lib:SOT-223-3_L6.5-W3.4-P2.30-LS7.0-BRU5
1Conn_02x05_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical_SMDJ4
1DPDTspecific-parts-lib:SW-SMD_MST22D18G2SW3
1DRV8353SRTATspecific-parts-lib:WQFN-40_L6.0-W6.0-P0.50-TL-EP4.2U2
1ESP32-S3-WROOM-1specific-parts-lib:WIRELM-SMD_ESP32-S3-WROOM-1U1
1G***kibuzzard-6A76AAA5kibuzzard-6A76AAA5
1G***kibuzzard-6A193405kibuzzard-6A193405
1G***kibuzzard-6A76A86Bkibuzzard-6A76A86B
1G***kibuzzard-6A797050kibuzzard-6A797050
1G***kibuzzard-6A76AA3Bkibuzzard-6A76AA3B
1G***kibuzzard-6A193411kibuzzard-6A193411
1G***kibuzzard-6A76AB0Ckibuzzard-6A76AB0C
1G***kibuzzard-6A76A908kibuzzard-6A76A908
1G***kibuzzard-6A76A790kibuzzard-6A76A790
1G***kibuzzard-6A76A80Fkibuzzard-6A76A80F
1G***kibuzzard-6A76AAE1kibuzzard-6A76AAE1
1G***kibuzzard-6A1931C8kibuzzard-6A1931C8
1G***kibuzzard-6A76A7BDkibuzzard-6A76A7BD
1G***kibuzzard-6A76AB8Bkibuzzard-6A76AB8B
1G***kibuzzard-6A76A802kibuzzard-6A76A802
1G***kibuzzard-6A76AAC0kibuzzard-6A76AAC0
1G***kibuzzard-6A79703Akibuzzard-6A79703A
1G***kibuzzard-6A76AB7Dkibuzzard-6A76AB7D
1G***kibuzzard-6A7D4481kibuzzard-6A7D4481
1G***kibuzzard-6A1931D7kibuzzard-6A1931D7
1G***kibuzzard-6A76A8BCkibuzzard-6A76A8BC
1G***kibuzzard-6A1931DCkibuzzard-6A1931DC
1G***kibuzzard-6A76A5F0kibuzzard-6A76A5F0
1G***kibuzzard-6A1928DDkibuzzard-6A1928DD
1G***kibuzzard-6A76A5A9kibuzzard-6A76A5A9
1G***kibuzzard-6A793D41kibuzzard-6A793D41
1G***kibuzzard-6A192903kibuzzard-6A192903
1G***kibuzzard-6A76AA0Akibuzzard-6A76AA0A
1G***kibuzzard-6A76A991kibuzzard-6A76A991
1G***kibuzzard-6A76A548kibuzzard-6A76A548
1G***kibuzzard-6A76AD5Akibuzzard-6A76AD5A
1G***kibuzzard-6A76A7CEkibuzzard-6A76A7CE
1G***kibuzzard-6A1931CDkibuzzard-6A1931CD
1G***kibuzzard-6A76ABC4kibuzzard-6A76ABC4
1G***kibuzzard-6A76AB97kibuzzard-6A76AB97
1G***kibuzzard-6A76A904kibuzzard-6A76A904
1G***kibuzzard-6A1931E2kibuzzard-6A1931E2
1G***kibuzzard-6A7D445Bkibuzzard-6A7D445B
1G***kibuzzard-6A76A71Ckibuzzard-6A76A71C
1G***kibuzzard-6A76A5E2kibuzzard-6A76A5E2

The 157 most common of 175 parts.

Similar boards

  • 4 layers35 × 35 mmCanonical, the printed circuit board in 3D

    Canonical

    AnasSarkiz/smart-nema14-motor-controller

    STEPPERONLINE 14HM11-0404S controller — unrouted work-in-progress prototype; mechanical and electrical qualification pending

    213 parts
  • 4 layers74.1 × 99.3 mmController, the printed circuit board in 3D

    Controller

    Choccy-vr/BeanBike

    A DIY eBike display and controller.

    78 parts
  • 4 layers44.1 × 50 mmUSB Mic, the printed circuit board in 3D

    USB Mic

    ConfusedHello/USB-Mic

    A DIY USB-C Microphone!

    71 parts19
  • 2 layers62.8 × 32.1 mmAislador USB, the printed circuit board in 3D

    Aislador USB

    FreddyUrena/Freddy_Urena_Electiva_2025_C1

    25 parts
  • 4 layers60 × 60 mmBLDC Controller, the printed circuit board in 3D

    BLDC Controller

    HSabinoR/K-9R

    A Low-Cost (hopefully) Robotic Dog

    84 parts
  • 4 layers94.3 × 95.7 mmMotor bldc esc V1, the printed circuit board in 3D

    Motor bldc esc V1

    middelhauvephilipp-stack/motor_control_pcb_design

    117 partsCERN-OHL-P-2.0
  • 2 layers59 × 36 mmPCB USB, the printed circuit board in 3D

    PCB USB

    vladimirlpc21/Vladimir_lopez_cabrera_Electiva_2025_C1

    15 parts
  • 2 layers112.7 × 121.4 mmPCBOFBEATPAD, the printed circuit board in 3D

    PCBOFBEATPAD

    Axe-1st/OrphBeatPad

    A custom Beat pad with awesome design!

    74 parts2

Questions

How big is the Pace core PCB?

It measures 100 × 80.1 mm and has 4 copper layers, 1.57 mm thick.

What parts does the Pace core use?

175 parts, built around the ESP32-S3-WROOM-1-N16R2, DRV8353SRTAT, SM06B-SRSS-TB(LF)(SN) and ADUM3160BRWZ-RL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pace core KiCad files?

From the rammp-org/pace-racer-hardware repository on GitHub, at the commit this page was made from: the board is pace-core/pace-core.kicad_pcb and its schematic pace-core/pace-3-phase-inverter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pace core design in my own project?

Its repository states no licence, so its author keeps all rights: ask rammp-org before reusing the design.