

RadioHAT
Raspberry Pi PCIe HAT for radio modules
- Size
- 65 × 56.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 61
- Pads
- 211
- Tracks, vias
- 400, 185
- Pours
- 152
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 18 Jul 2025
- Updated
- 23 Oct 2026
Overview
RadioHAT is an open-source printed circuit board by radiolib-org, from the radiolib-org/RadioHAT repository on GitHub, published under the MIT licence. It is a 2-layer board of 65 × 56.5 mm with 37 parts on 61 nets, routed with 400 tracks and 185 vias.
Its parts include 22 resistors, 5 capacitors, 4 connectors and 2 ICs. It belongs with the radio and wireless boards of this library.
README
README.mdRadioHAT
Raspberry Pi PCIe HAT for radio modules
This HAT is an all-in-one radio modules development platform with the following features.
- Built-in logic analyzer - All pins routed to the transceivers (SPI and various GPIO signals) are also routed to additional Raspberry Pi GPIO pins, to allow the RPi to monitor and record the state of communication pins. See the pinalyzer repository for details.
- Adjustable linear voltage regulator - To supply power-intensive transceivers, there is a dedicated LDO regulator with adjustable output. The output voltage is adjustable between 2.9 and 3.6 V.
- Power consumption measurement - There is a built-in INA219 current monitor which allows to measure the power consumption of the transceiver. See the dc-powermon repository for details.
While these features are useful, they are entirely optional. Without them, the HAT is a simple adapter board for mini-PCIe cards (half-size or full-size) and can be left with most of the components unpopulated, except for the RPi pin header, PCIe connector and the card latch.
RadioHAT

Card for modules from Dorji

Card for modules from GNice-RF

Card for modules from Ebyte

Card for Wio-E5

Mini PCIe connector pinout
Different vendors (RAK Wireless, Waveshare, SeeedStudio and others) offer radio modules in the mini-PCIe card form factor. However, there seems to be no consensus on any specific pinout. Naturally, RadioLib defines its own version to add to the confusion. However, we try to adhere to the standard Mini PCIe 2.0 pinout in the following ways:
- Mini PCIe 2.0 SMB pins are used for I2C
- Mini PCIe 2.0 USB pins are used for USB
- IRQs, resets and various GPIOs are connected to Mini PCIe 2.0 digital signals
- 3.3V voltage pins are used for most modules, though sometimes 5V is optionally used
The complete pinout of the connector (and therefore the PCIe cards) is shown below.
| Pin | Signal | Signal | Pin |
|---|---|---|---|
| 1 | GPIO0 | 3V3 | 2 |
| 3 | IRQ0 | GND | 4 |
| 5 | IRQ1 | 5V | 6 |
| 7 | GPIO1 | NC | 8 |
| 9 | GND | NC | 10 |
| 11 | RST0 | NC | 12 |
| 13 | RST1 | NC | 14 |
| 15 | GND | NC | 16 |
| 17 | NC | GND | 18 |
| 19 | NC | NSS1 | 20 |
| 21 | GND | NC | 22 |
| 23 | NC | 3V3 | 24 |
| 25 | NC | GND | 26 |
| 27 | GND | 5V | 28 |
| 29 | GND | I2C_SCL | 30 |
| 31 | PPS | I2C_SDA | 32 |
| 33 | NC | GND | 34 |
| 35 | GND | USB_D- | 36 |
| 37 | GND | USB_D+ | 38 |
| 39 | 3V3 | GND | 40 |
| 41 | 3V3 | LED0 | 42 |
| 43 | GND | LED1 | 44 |
| 45 | SPI_SCK | LED2 | 46 |
| 47 | SPI_MISO | 5V | 48 |
| 49 | SPI_MOSI | GND | 50 |
| 51 | NSS0 | 3V3 | 52 |
Raspberry Pi pinout
The shield routes the Mini PCIe connector signals to the following Raspberry Pi GPIO header pins. The pins with prefix SNS_ are connected to the digital signals through a series resistor and GPIO, allowing to use the RPi as a makeshift logic analyzer.
| Pin | Signal | Signal | Pin |
|---|---|---|---|
| 1 | 3V3 | 5V | 2 |
| 3 | I2C_SCL | 5V | 4 |
| 5 | I2C_SDA | GND | 6 |
| 7 | SNS_NSS0 | SNS_SDA | 8 |
| 9 | GND | SNS_SCL | 10 |
| 11 | SNS_SCK | RST0 | 12 |
| 13 | SNS_MISO | GND | 14 |
| 15 | SNS_MOSI | GPIO1 | 16 |
| 17 | 3V3 | IRQ1 | 18 |
| 19 | SPI_MOSI | GND | 20 |
| 21 | SPI_MISO | RST1 | 22 |
| 23 | SPI_SCK | NSS0 | 24 |
| 25 | GND | NSS1 | 26 |
| 27 | NC | NC | 28 |
| 29 | SNS_IRQ0 | GND | 30 |
| 31 | SNS_RST0 | SNS_GPIO0 | 32 |
| 33 | SNS_NSS1 | GND | 34 |
| 35 | SNS_IRQ1 | IRQ0 | 36 |
| 37 | SNS_GPIO1 | GPIO0 | 38 |
| 39 | GND | SNS_RST1 | 40 |
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15, R16, R19, R20 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4, C5 |
| 2 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 2 | 10R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17, R18 |
| 2 | Conn_02x07_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x07_P2.54mm_Vertical | J3, J4 |
| 2 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm_NumberLabels | JP1, JP2 |
| 1 | 100m | RadioHAT:R_2512_6332Metric_Pad1.40x3.35mm_HandSolder_Bypass | R14 |
| 1 | 2k | RadioHAT:Potentiometer_Bourns_3362P1200LF | R21 |
| 1 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R22 |
| 1 | INA219AxD | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | LP3855-ADJ | RadioHAT:SOT150P700X180-5N | U2 |
| 1 | RPi_GPIO | RadioHAT:RPI_Hat_B+ | J1 |
| 1 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP3 |
| 1 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm_NumberLabels | JP5 |
| 1 | ~ | RadioHAT:Mini_PCIe_Latch_Hole | J2 |
More from radiolib-org/RadioHAT
6- 2 layers30 × 51 mm

- 2 layers30 × 51 mm

- 2 layers30 × 51 mm

- 2 layers30 × 51 mm

RadioHAT Card SX1280 Dual Channel
radiolib-org/RadioHAT
Raspberry Pi PCIe HAT for radio modules
9 parts12MIT - 2 layers30 × 51 mm

- 2 layers30 × 51 mm

Similar boards
- 2 layers40 × 34 mm

- 2 layers53.9 × 23.2 mm

Analog
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
37 parts1kGPL-3.0 - 2 layers52 × 51.8 mm

Esp32-homeassistant rf bridge
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
37 parts915 - 2 layers87.8 × 59.8 mm

FreeDeck SMD 2020-02
FreeYourStream/freedeck-hardware
all the stuff you need to build your own FreeDeck
37 parts772 - 2 layers65 × 28 mm

BMS Cell Module
stuartpittaway/diyBMS
Do it yourself battery management system for Lithium ion battery packs/cells
37 parts676GPL-3.0 - 2 layers48 × 32 mm

FlatSat
Pwnsat/FlatSat
Flatsat v1.0 is a hardware based platform for aerospace cybersecurity research
37 parts575GPL-2.0 - 2 layers38.1 × 153.7 mm

- 2 layers47.8 × 27.4 mm

Vsf stm32h7b0
vsfteam/vsf
Versaloon Software Framework -- a tiny preemptive-capable event-driven incremental software framework for embedded systems
37 parts341Apache-2.0
Questions
How big is the RadioHAT PCB?
It measures 65 × 56.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RadioHAT use?
37 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RadioHAT KiCad files?
From the radiolib-org/RadioHAT repository on GitHub, at the commit this page was made from: the board is RadioHAT.kicad_pcb and its schematic RadioHAT.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the RadioHAT design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).