

Hbridge controller
kicad schematics for pypilot components
- Size
- 50 × 75 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 47
- Pads
- 160
- Tracks, vias
- 733, 11
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 18 Aug 2020
- Updated
- 7 Jun 2024
Overview
Hbridge controller is an open-source printed circuit board by pypilot, from the pypilot/pypilot_schematics repository on GitHub. It is a 2-layer board of 50 × 75 mm with 50 parts on 47 nets, routed with 733 tracks and 11 vias.
It is built around the NCP5106BD, CPC5001G and MUR160. Its parts include 17 resistors, 9 capacitors, 9 connectors, 5 transistors and 3 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3NCP5106BD
SOIC-8-150mil-40℃~+125℃ 10V~20V 2 250mA 250uA 35ns 500mA 85ns Half-Bridge IGBT、MOSFET Under Voltage Protection SOIC-8-150mil Gate Drivers ROHSonsemiGate DriversCPC5001G
DIP-8-40℃~+85℃ 100ns 2 2.7V~5.5V 250ns 3.75kV 5Mbps 7kV/us 800mW DC DIP-8 Logic Output Optoisolators ROHSLittelfuse/IXYSLogic Output OptoisolatorsMUR160
DO-41-65℃~+175℃ 1 Independent 1.25V@1A 1A 35A 5uA@600V 600V 75ns DO-41 Fast Recovery / High Efficiency Diodes ROHSonsemiFast Recovery / High Efficiency Diodes
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | Q_NMOS_GDS | Package_TO_SOT_THT:TO-220-3_Vertical | Q1, Q2, Q3, Q4, Q5 |
| 4 | 47 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R16, R17, R18, R19 |
| 3 | 100k | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R5, R6, R8 |
| 3 | 560 | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R2, R3, R12 |
| 2 | .1uF | Capacitors_THT:C_Disc_D7.0mm_W2.5mm_P5.00mm | C1, C2 |
| 2 | 1uF | Capacitor_THT:C_Disc_D7.0mm_W2.5mm_P5.00mm | C5, C6 |
| 2 | 2.4k | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R10, R11 |
| 2 | 330uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C9, C10 |
| 2 | 4.7uF | Capacitor_THT:C_Disc_D8.0mm_W2.5mm_P5.00mm | C7, C8 |
| 2 | MUR160 | Diode_THT:D_T-1_P2.54mm_Vertical_AnodeUp | D1, D2 |
| 2 | NCP5106B | Package_DIP:DIP-8_W7.62mm | U2, U3 |
| 1 | 10k | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R4 |
| 1 | 10mOhm | hbridge_footprints:Resistor_Horizontal_RM10mm | R20 |
| 1 | 12v REG/R | Package_TO_SOT_THT:TO-220-3_Vertical | J5 |
| 1 | 20 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1 |
| 1 | 200 | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R7 |
| 1 | 30k | Resistors_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R9 |
| 1 | 4.7uF | hbridge_footprints:C_Disc_D5.0mm_W2.5mm_P2.50mm | C4 |
| 1 | Arduino_Nano_v3.x | hbridge_footprints:arduino_mini | A1 |
| 1 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J1 |
| 1 | End Stops | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | FUSE | hbridge_footprints:BladeFuse-CarType | F1 |
| 1 | Motor A | hbridge_footprints:Power | J9 |
| 1 | Motor B | hbridge_footprints:Power | J8 |
| 1 | Pwr+ | hbridge_footprints:screw_terminal | J7 |
| 1 | Pwr- | hbridge_footprints:screw_terminal | J6 |
| 1 | SENSE | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J3 |
| 1 | TVS | freetronics_footprints:DIODE-1N4001 | TVS2 |
| 1 | TVS | hbridge_footprints:tvs | TVS1 |
| 1 | Thermistor | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P5.08mm_Vertical | TH1 |
| 1 | UART_Device | hbridge_footprints:uart | J4 |
| 1 | cpc5001 | Package_DIP:DIP-8_W7.62mm | U1 |
More from pypilot/pypilot_schematics
12- 4 layers116 × 86.4 mm

- 4 layers103.4 × 71.6 mm

- 4 layers75.1 × 50 mm

- 2 layers65.8 × 90.7 mm

- 4 layers76.1 × 51.2 mm

- 2 layers48.8 × 72.3 mm

- 2 layers75.1 × 50 mm

- 2 layers25.8 × 60.4 mm

- 2 layers25.4 × 36.4 mm

- 2 layers48.6 × 21 mm

- 2 layers45.7 × 25 mm

- 2 layers21.2 × 30 mm

Similar boards
- 4 layers170.2 × 137.2 mm

Standaert ha
RockinRoel/standaert-ha
This repository contains the KiCAD schematic and PCB design for the custom board used in the home automation system at my parents' house.
173 parts - 2 layers61.4 × 68.5 mm

PWM 6 step SVPWM ADM3223
abd-alaj/BLDC-motor-custom-inverter
Matlab, Simulink, Hardware and C-code for a custom inverter project.
45 parts1 - 2 layers100 × 50 mm

Nixie control board
alxhoff/Nixie-tube-clock
Firmware for a nixie tube clock based on STM32 hal libraries
43 parts1GPL-3.0 - 2 layers100 × 100 mm

ControlMotorCC
NicoAvedano/Proyectos-Esquematicos-y-PCBs
Distintos diseños de circuitos impresos de gran calidad para trabajos de laboratorio.
72 parts - 2 layers187.2 × 26.6 mm

- 2 layers45.7 × 25.9 mm

- 2 layers21 × 31.5 mm

- 2 layers42 × 32.5 mm

Lipoboard
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
50 parts915
Questions
How big is the Hbridge controller PCB?
It measures 50 × 75 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Hbridge controller use?
50 parts, built around the NCP5106BD, CPC5001G and MUR160. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hbridge controller KiCad files?
From the pypilot/pypilot_schematics repository on GitHub, at the commit this page was made from: the board is hbridge_controller/hbridge_controller.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hbridge controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask pypilot before reusing the design.