
Flashmultiplexer
pruttelherrie/Ehx9-All
Modifications for the Electro Harmonix '9' line of pedals.

Modifications for the Electro Harmonix '9' line of pedals.
Ehx9adapterpcb is an open-source printed circuit board by pruttelherrie, from the pruttelherrie/Ehx9-All repository on GitHub. It is a 2-layer board of 110.5 × 88 mm with 37 parts on 59 nets, routed with 694 tracks and 49 vias.
Its parts include 13 diodes, 6 resistors, 5 capacitors, 5 connectors and 5 switches. It belongs with the audio and music boards of this library.
Do not use the EEPROM store code from before 2021-10-01! It will eat up your flash writes like candy because of the braindead EEPROM.write lib in the stm32duino core. Fixed in callbacks.h and main.cpp, dd 2021-10-01
Electro Harmonix' 9 series of pedals is a range of polyphonic synthesis pedals for guitar. The effects and sounds that can be obtained are superb, however they have a few shortcomings: first of all they are not programmable (i.e. there's only one setting, no way to store favourites and recall them quickly) and if you have more than one, they tend to take up quite a lot of space on a pedalboard, especially if one uses them only sparingly during a set.
The modifications documented in this repository try to eliminate these shortcomings.
To store and recall settings, the pots and switch are removed. GPIOs from the microcontroller are connected to the main board to replace the functionality of the pots and the switch. Since we use a PWM signal for the pots, it is low-pass filtered by a simple first-order RC network.
Encoders take the place of the pots and the switch, a TFT is added for visual feedback of the settings.
All pedals of this serie share the same PCB. The difference is in the firmware of the DSP. This firmware is stored in an EEPROM. By multiplexing multiple EEPROMS on one board and resetting the DSP after switching the multiplexer, one can switch between pedals of the series within one enclosure.
Modding a pedal is not for the faint of heart. It is pretty easy to destroy the pedal in the process. Also, a number of tools are needed:
The BOMs for the PCBs can be found in their folders: controller multiplexer
The multiplexer firmware was made with the Arduino IDE.
The controller firmware was made with VSCode + PlatformIO.
TBD: text and images.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | D | Diode_THT:D_DO-34_SOD68_P7.62mm_Horizontal | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12 |
| 5 | Rotary_Encoder_Switch | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW1, SW2, SW3, SW4, SW5 |
| 4 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R1, R2, R3, R4 |
| 4 | 1u | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1, C2, C3, C4 |
| 2 | Conn_01x20_Male | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J1, J2 |
| 1 | 100n | Capacitor_THT:C_Rect_L7.0mm_W2.0mm_P5.00mm | C5 |
| 1 | 220R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R6 |
| 1 | 270R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R5 |
| 1 | Conn_01x05_Male | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | pots1 |
| 1 | D | Diode_THT:D_DO-34_SOD68_P2.54mm_Vertical_KathodeUp | D13 |
| 1 | MIDI | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | MIDI1 |
| 1 | PC900 | Package_DIP:DIP-6_W7.62mm_LongPads | U1 |
| 1 | PWR | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | TFT | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J3 |
| 1 | switch | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J4 |

pruttelherrie/Ehx9-All
Modifications for the Electro Harmonix '9' line of pedals.


hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

FreeYourStream/freedeck-hardware
all the stuff you need to build your own FreeDeck

stuartpittaway/diyBMS
Do it yourself battery management system for Lithium ion battery packs/cells

Pwnsat/FlatSat
Flatsat v1.0 is a hardware based platform for aerospace cybersecurity research


vsfteam/vsf
Versaloon Software Framework -- a tiny preemptive-capable event-driven incremental software framework for embedded systems
It measures 110.5 × 88 mm and has 2 copper layers, 1.6 mm thick.
37 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the pruttelherrie/Ehx9-All repository on GitHub, at the commit this page was made from: the board is controller-pcb/ehx9adapterpcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask pruttelherrie before reusing the design.