

Camcontrol
repo for the lyra flight computer
- Size
- 25.4 × 25.4 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 64
- Nets
- 89
- Pads
- 260
- Tracks, vias
- 605, 97
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 15 Nov 2023
- Updated
- 30 May 2026
Overview
Camcontrol is an open-source printed circuit board by prs2026, from the prs2026/Lyra-flight-computer repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 25.4 × 25.4 mm with 64 parts on 89 nets, routed with 605 tracks and 97 vias.
It is built around the RP2040, E22-900MM22S and W25Q128JVSIQ, with the TPS1HC30BQPWPRQ1, XC6206P332MR and AO3401A among its other parts. Its parts include 20 resistors, 18 capacitors, 8 connectors, 6 ICs and 4 transistors. It belongs with the RP2040 boards of this library.
Main components
7RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)E22-900MM22S
SMD,10x10mm-147dBm 1.8V~3.7V 119mA 22.3dBm 6.8mA 7km 915MHz Continuous frequency coverage LoRa SPI Stamp Hole Antenna、IPEX interface SMD,10x10mm LoRa Modules ROHSChengdu Ebyte Elec TechLoRa ModulesW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHTPS1HC30BQPWPRQ1
HTSSOP-14-40℃~+125℃ 1 3V~28V 57mΩ 5A Active High High Side Switch Under-voltage lockout、Reverse voltage protection、Integrated charge pump、Overcurrent Protection、Over temperature protection、Latch protection、Short-Circuit Protection HTSSOP-14 Power Distribution Switches ROHSTexas InstrumentsPower Management - SpecializedXC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsSX1M12.000M10F30TNN
SMD2016-4P-40℃~+85℃ 1.62V~3.63V 10mA 12MHz CMOS ±10ppm ±30ppm SMD2016-4P Crystal Oscillators ROHSShenzhen SCTF ElecCrystal Oscillators
README
README.mdLyra-flight-computer
repo for the lyra flight computer
Parts
64| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C10, C14, C17, C18, C19, C20, C21, C22, C29 |
| 7 | 5.1k | Resistor_SMD:R_0402_1005Metric | R6, R14, R15, R16, R17, R18, R19 |
| 5 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R3, R9, R11, R25 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric | C5, C6, C13, C15 |
| 4 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 4 | Power 1 | .pretty:wago2pin3mmspace | J1, J3, J4, J7 |
| 2 | 220n | Capacitor_SMD:C_0402_1005Metric | C26, C28 |
| 2 | 22R | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | 22n | Capacitor_SMD:C_0402_1005Metric | C27, C30 |
| 2 | 27k | Resistor_SMD:R_0402_1005Metric | R7, R23 |
| 2 | 50k | Resistor_SMD:R_0402_1005Metric | R12, R21 |
| 2 | 51k | Resistor_SMD:R_0402_1005Metric | R8, R24 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D1, D3 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad | H1, H2 |
| 2 | TPS1HC30BQPWPRQ1 | .pretty:HTSSOP-14_L5.0-W4.4-P0.65-LS6.4-BL-EP-3 | U2, U7 |
| 1 | Antenna_Shield | .pretty:ANT-SMD_1909763-1 | AE1 |
| 1 | Conn_01x02 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | J6 |
| 1 | Conn_01x02 | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | J5 |
| 1 | Conn_01x03 | Connector_PinHeader_2.00mm:PinHeader_1x03_P2.00mm_Vertical | J8 |
| 1 | D_Schottky | Diode_SMD:D_SOD-323F | D4 |
| 1 | E22-900MM22S | .pretty:WIRELM-SMD_E22-400MM22S | U1 |
| 1 | Jumper | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U6 |
| 1 | SX1M12.000M10F30TNN | easyeda2kicad2:OSC-SMD_4P-L2.0-W1.6-BL | X1 |
| 1 | USB_B_Micro | easyeda2kicad2:MICRO-USB-SMD_U254-051T-4BHJ25-F2S | J2 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U5 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23-3 | U4 |
More from prs2026/Lyra-flight-computer
12- 4 layers50 × 60 mm

- 4 layers50 × 60 mm

- 4 layers112 × 28 mm

- 4 layers22 × 53 mm

- 4 layers25 × 55 mm

- 4 layers54.3 × 39.1 mm

- 4 layers40 × 75 mm

- 2 layers66 × 100 mm

- 4 layers20 × 60 mm

- 4 layers40 × 75 mm

- 4 layers40 × 75 mm

- 4 layers18 × 40 mm

Similar boards
- 4 layers51.8 × 45.1 mm

Spark rp2040-swd probe
emb3rcia/spark-rp2040-swd-probe
Open-source financialy-accesible SWD probe.
72 parts1 - 2 layers20 × 45 mm

Lora board
acseka360/sws_lbn
The interactive BOM webpage helps during assembly. You can mark components placed and check their exact types.
32 parts1 - 6 layers34 × 56 mm

- 2 layers60 × 60 mm

Lora board
acseka360/sws_lsb
The interactive BOM webpage helps during assembly. You can mark components placed and check their exact types.
22 parts - 6 layers30 × 60 mm

LSR FLCM0001 A03
Louisiana-State-Rocketry/FLCM0001-A03_PCB
PCB Files for the Eclipse 2 Flight Computer.
150 partsMIT - 2 layers26.5 × 34.4 mm

PicoLoaderNSB
makeo/PicoLoader
A cheap and easy to install modchip for the Nintendo GameCube!
45 parts320GPL-2.0 - 2 layers35.9 × 62.7 mm

Rp2040-memcard
sd2psx/pcb
The PCB must be produced in 0.8mm thickness. Production files are provided under the "Releases" tab. These do not include the through-hole OLED module.
60 parts241 - 4 layers51.4 × 60.6 mm

Gb rp2040 cart
deltabeard/DBGC
A Game Boy cartridge using the Raspberry Pi RP2040 with RTC and MBC support.
67 parts57
Questions
How big is the Camcontrol PCB?
It measures 25.4 × 25.4 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Camcontrol use?
64 parts, built around the RP2040, E22-900MM22S, W25Q128JVSIQ and TPS1HC30BQPWPRQ1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Camcontrol KiCad files?
From the prs2026/Lyra-flight-computer repository on GitHub, at the commit this page was made from: the board is CamControl/camcontrol/camcontrol.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Camcontrol design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).