

ZxRebornClock
Часы на ГРИ ИН-14 с синхронизацией времени через интернет
- Size
- 148.5 × 90 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 125
- Nets
- 120
- Pads
- 415
- Tracks, vias
- 921, 72
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 12 Nov 2024
- Updated
- 22 Nov 2025
Overview
ZxRebornClock is an open-source printed circuit board by popovb, from the popovb/zxRebornClock repository on GitHub, published under the MIT licence. It is a 2-layer board of 148.5 × 90 mm with 125 parts on 120 nets, routed with 921 tracks and 72 vias.
It is built around the CH32X035C8T6, ESP-12F and MC34063, with the TLP627(F), AMS1117-3.3 and DS1302 among its other parts. Its parts include 58 resistors, 12 transistors, 11 capacitors, 10 ICs and 8 diodes. It belongs with the ESP8266 boards of this library.
Main components
12CH32X035C8T6
LQFP-48(7x7)Microcontrollers (MCU/MPU/SOC)WCH (Nanjing Qinheng Microelectronics)ESP-12F
SMD,24x16mm-40℃~+85℃ -96dBm 15dBm 2.4GHz 3.3V 375mA 55mA PCB UART WIFI4 SMD,24x16mm WiFi Modules ROHSDOITWiFi ModulesMC34063
SOP-80℃~+70℃@(TA) 1 33kHz 3V~40V Adjustable Buck、Boost Built-in Inverting No SOP-8 DC-DC Converters ROHSHXY MOSFETDC-DC ConvertersTLP627(F)
DIP-4-55℃~+100℃ 1 1.15V 1.2V@100mA,10mA 150mA 15us@10mA,100Ω 300V 40us@10mA,100Ω 5kV DC Darlington Transistor DIP-4 Transistor, Photovoltaic Output Optoisolators ROHSToshibaTransistor, Photovoltaic Output OptoisolatorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsDS1302
SOP-8SOP-8 Real Time Clocks ROHSTDDReal Time ClocksUSBLC6-4SC6
SOT-23-6-55℃~+125℃ 0.3pF 15V 300W@8/20us 4.7A@8/20us 5V 6V 80nA ESD Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Unidirectional SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)MMBTA42
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mV 300V 350mW 500mA 50MHz 5V NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)US1G
SMA-55℃~+150℃ 1 Independent 1.3V@1A 1A 30A 400V 50ns 5uA SMA Fast Recovery / High Efficiency Diodes ROHSShunYeFast Recovery / High Efficiency DiodesIRF740
TO-220-55℃~+175℃ 1 N-channel 1.162nF 100W 10A 17pF 32nC@10V 400V 4V 500mΩ@10V N-Channel TO-220 MOSFETs ROHSMinosMOSFETsLL4148
LL-341 Independent 1V@10mA 200mA 4A 4ns 500mW 5uA@75V 75V LL-34 Switching Diodes ROHSMDDSwitching DiodesMMBTA56
SOT-23-55℃~+150℃ 1 PNP 100 100nA 225mW 250mV 4V 500mA 50MHz 80V PNP SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
README
README.md

ИНСТРУКЦИЯ ПО СБОРКЕ И ЗАПУСКУ
Повышайка на 200 В
Запаиваем следующие элементы: J1, U3, C8, R55, C9, L1, D8, C11, D7, Q12, R56, Q11, C10, R57, R58.
Подключаем 12 В. На С11 долно быть около 200 В. Если есть, переходим к следующему шагу.
Понижайка на 3.3 В
Запаиваем следующие элементы: D6, C2, U2, C4, C5, R1, D1. Подключаем 12 В. На C4 должно быть
3.3 В и горит D1. Если есть, переходим к следующему шагу.
Микроконтроллер
Запаиваем: U1, C1, J2, U4, R12-R15, D2-D5, Sw2-Sw6, R29-R33, R53, R54, J4.
Идём сюда https://github.com/ch32-rs/wchisp/releases/tag/v0.3.0 и берём прошиватор под нужную платформу. Как минимум работает в Debian и Windows 10.
Плата обесточена. Зажимаем кнопку Download, подрубаем usb кабель к компу, отпускаем кнопку и у нас несколько секунд, чтобы запустить прошиватор.
Для начала можно дать команду вывода информации чипа: wchisp info.
Если заработало, то можно прошить blink.hex из раздела релизов. Команда wchisp flash blink.hex. Будут
мигать светодиоды D2-D5.
Если всё работает -- прошиваем боевую прошивку: zxRebornClock.hex.
Конфигурирование
Питание 12 В и USB выключены. Зажимаем кнопку F и подаём питание 12 В. Загорается зелёный светодиод -- контроллер перешёл в режим конфигурирования.
Подключаем к J4 USB-Uart переходник и подключаем его к компьютеру.
Из раздела релизов берём программу конфигуратор zxrc_configurator.win64.exe или
zxrc_configurator_lin64 (проверял в Windows 10 и Debian). Запускаем,
выбираем ком-порт и отвечаем на вопросы. В конце будет выдано подтверждение успеха
конфигурирования.
Дальше
Запаиваем всё остальное. Должно всё заработать.
Если не заработало?
Тогда идём сюда и спрашиваем https://t.me/zxRebornClock
Parts
125| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 470K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R35, R36, R37, R38, R39, R40, R41, R42, R43, R44, R45, R46, R47, R48, R51, R52 |
| 15 | 4,7K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R4, R5, R6, R16, R17, R18, R19, R20, R29, R30, R31, R32, R33 |
| 12 | 47K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R8, R9, R10, R11, R21, R22, R23, R24, R25, R53, R54 |
| 10 | MMBTA42 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10 |
| 5 | 1,0K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R12, R13, R14, R15 |
| 5 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R26, R27, R34, R49, R50 |
| 4 | 0,1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C6, C7 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H24, H25, H26, H27 |
| 4 | TLP627 | Package_DIP:DIP-4_W7.62mm | U7, U8, U9, U10 |
| 4 | ИН-14 | Library:ИН-14 | VL1, VL2, VL3, VL4 |
| 2 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C5 |
| 2 | US1G | Diode_SMD:D_SMA | D6, D8 |
| 2 | Гребёнка 1x3x2.54 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4, J5 |
| 1 | 0.01uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 0.33 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R55 |
| 1 | 1000uF | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C4 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R56 |
| 1 | 2.2uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C11 |
| 1 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R28 |
| 1 | 2200pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8 |
| 1 | 220uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C9 |
| 1 | 220uH | Inductor_SMD:L_12x12mm_H8mm | L1 |
| 1 | 32768 | Crystal:Crystal_C38-LF_D3.0mm_L8.0mm_Horizontal | Y1 |
| 1 | 3K 1% | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R58 |
| 1 | 470K 1% | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R57 |
| 1 | 50K 3362P | Library:TRIM_3362P-1-103 | RV1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | CH32X035C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | D | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW2 |
| 1 | DS1302 | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | ESP-12F | RF_Module:ESP-12E | U6 |
| 1 | F | Button_Switch_THT:SW_PUSH_6mm_H9.5mm | SW6 |
| 1 | HH | Button_Switch_THT:SW_PUSH_6mm_H9.5mm | SW3 |
| 1 | IRF740 | Package_TO_SOT_THT:TO-220-3_Vertical | Q12 |
| 1 | Jack DC | Connector_BarrelJack:BarrelJack_Horizontal | J1 |
| 1 | LL4148 | Diode_SMD:D_MiniMELF | D7 |
| 1 | LOGO | Library:logo | G*** |
| 1 | MC34063 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | MM | Button_Switch_THT:SW_PUSH_6mm_H9.5mm | SW4 |
| 1 | MMBTA56 | Package_TO_SOT_SMD:SOT-23 | Q11 |
| 1 | MicroUSB type B розетка | Connector_USB:USB_Micro-B_Molex-105017-0001 | J2 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | SS | Button_Switch_THT:SW_PUSH_6mm_H9.5mm | SW5 |
| 1 | USBLC6-4SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | blue | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5 |
| 1 | green | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | red | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | white | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | yellow | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | Гребёнка 1x2x2.54 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Гребёнка 1x4x2.54 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Держатель CR2032 | Battery:BatteryHolder_MYOUNG_BS-07-A1BJ001_CR2032 | BT1 |
The 124 most common of 125 parts.
Similar boards
- 2 layers176 × 82.6 mm

- 4 layers148.9 × 56 mm

- 4 layers100 × 129.8 mm

- 2 layers65 × 50 mm

- 2 layers69 × 99.1 mm

- 6 layers75.4 × 19.6 mm

- 2 layers150 × 95 mm

- 2 layers88 × 55 mm

Questions
How big is the ZxRebornClock PCB?
It measures 148.5 × 90 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ZxRebornClock use?
125 parts, built around the CH32X035C8T6, ESP-12F, MC34063 and TLP627(F). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ZxRebornClock KiCad files?
From the popovb/zxRebornClock repository on GitHub, at the commit this page was made from: the board is kicad/zxRebornClock/zxRebornClock.kicad_pcb and its schematic kicad/zxRebornClock/zxRebornClock.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ZxRebornClock design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).