.kicad_pcb.jpg?size=s&soon)
Proto Nano old (4)
polymetric/proto-nano
This is an Arduino Nano clone I made in late May 2018. It was pretty much solely designed so that I could learn KiCad and SMD soldering, but I also kind of wanted an Arduino made in KiCad anyway.

This is an Arduino Nano clone I made in late May 2018. It was pretty much solely designed so that I could learn KiCad and SMD soldering, but I also kind of wanted an Arduino made in KiCad anyway.
Proto Nano old (2) is an open-source printed circuit board by polymetric, from the polymetric/proto-nano repository on GitHub. It is a 2-layer board of 43.2 × 17.8 mm with 32 parts on 43 nets, routed with 527 tracks and 55 vias.
It is built around the ATMEGA328P-AU, CH340G and LM1117-5.0. Its parts include 10 capacitors, 7 resistors, 5 diodes, 3 ICs and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
This is an Arduino Nano clone I made in late May 2018. It was pretty much solely designed so that I could learn KiCad and SMD soldering, but I also kind of wanted an Arduino made in KiCad anyway. This one has its problems, though, so I'll make a new one in the future that addresses these. Problems include, but are not limited to:
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 1K | Polymetric_Resistors_SMD:R_0603 | R1, R2, R3, R4, R5, R6, R7 |
| 5 | 100nF | Polymetric_Capacitors_SMD:C_0603 | C1, C2, C3, C6, C10 |
| 3 | 1uF | Polymetric_Capacitors_SMD:C_0603 | C4, C5, C7 |
| 2 | 4.7uF/T | Capacitors_Tantalum_SMD:CP_Tantalum_Case-A_EIA-3216-18_Reflow | C8, C9 |
| 1 | 12MHz | Polymetric_Resonators_SMD:murata-resonator_SMD_CSTCE16M0V53-R0 | Y1 |
| 1 | 16MHz | Polymetric_Resonators_SMD:murata-resonator_SMD_CSTCE16M0V53-R0 | Y2 |
| 1 | 1N5817 | Diodes_SMD:D_SOD-123 | D1 |
| 1 | ATMEGA328P-AU | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | U3 |
| 1 | Arduino_Nano_Socket | Polymetric_Shields_and_Sockets:Arduino_Nano_Shield | XA1 |
| 1 | CH340G | Housings_SSOP:SOP-16_4.4x10.4mm_Pitch1.27mm | U2 |
| 1 | D13 | Polymetric_LEDs_SMD:LED_0603 | D4 |
| 1 | ICSP_Header | Pin_Headers:Pin_Header_Straight_2x03_Pitch2.54mm | J2 |
| 1 | LM1117-5.0 | TO_SOT_Packages_SMD:SOT-223 | U1 |
| 1 | MF-MSMF050-2 500mA | Polymetric_Fuses_SMD:1812_PTC_Fuse | F1 |
| 1 | PWR | Polymetric_LEDs_SMD:LED_0603 | D5 |
| 1 | RESET | Buttons_Switches_SMD:SW_SPST_FSMSM | SW1 |
| 1 | RX | Polymetric_LEDs_SMD:LED_0603 | D3 |
| 1 | TX | Polymetric_LEDs_SMD:LED_0603 | D2 |
| 1 | USB_OTG | Polymetric_Shields_and_Sockets:USB_Micro-B_Molex-105017-0001 | J1 |
.kicad_pcb.jpg?size=s&soon)
polymetric/proto-nano
This is an Arduino Nano clone I made in late May 2018. It was pretty much solely designed so that I could learn KiCad and SMD soldering, but I also kind of wanted an Arduino made in KiCad anyway.

polymetric/proto-nano
This is an Arduino Nano clone I made in late May 2018. It was pretty much solely designed so that I could learn KiCad and SMD soldering, but I also kind of wanted an Arduino made in KiCad anyway.


ltrooney/diy-synth
A repository containing a handful of utilities for my DIY Eurorack-based modular synthesizer. Snippets include a virtual wavetable oscillator, a step sequencer, and more.

BenjiHansell/Radio-Controller
A 3D printed radio controller with a custom PCB and firmware.





It measures 43.2 × 17.8 mm and has 2 copper layers, 1.6 mm thick.
32 parts, built around the ATMEGA328P-AU, CH340G and LM1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the polymetric/proto-nano repository on GitHub, at the commit this page was made from: the board is old/Proto_Nano_old (2).kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask polymetric before reusing the design.