Skip to the content
2 layers35 × 25 mmIRLED Only, the printed circuit board in 3D

Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)

Size
35 × 25 mm
Copper layers
2
Thickness
0.81 mm
Parts
14
Nets
10
Pads
34
Tracks, vias
0, 0
Pours
10
Routed
Not yet
KiCad
KiCad 9.0 (file 20241229)
Created
17 Dec 2024
Updated
16 Oct 2026

Overview

IRLED Only is an open-source printed circuit board by PiTracLM, from the PiTracLM/PiTrac repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board of 35 × 25 mm with 14 parts on 10 nets.

It is built around the VSMA1085400.

Main components

1

README

Hardware/Archive/Connector Board v0.2/README.md

Description:

A small PCB that supports:

  1. high-speed (up to 1MHz), isolated switching of a high-power signal (12V, 100W) to a device such as an LED strobe; and
  2. connecting a GPIO camera shutter signal from one Raspberry Pi to the external trigger (XTR) of a Pi Global Shutter (GS) Camera that is connected to a second Raspberry Pi.

The board uses high-speed opto-isolators to keep the power plane of the two Pi’s isolated from each other and from the 12V switching circuit.

The PCB itself can be manufactured fairly inexpensively from the fabrication outputs at place like https://jlcpcb.com/ and https://pcbway.com .

The PiTrac DIY golf launch monitor project is using this board to drive its infrared strobe light and to allow one Pi to trigger the shutter of a second Pi. This is all used to capture the stop-motion images for the monitor.

Please consider supporting this work and the DIY LM project here: https://ko-fi.com/PiTrac

Parts Needed for Assembly:

ItemQtyReference(s)ValueLibPartFootprint / Details
11J3~USB B Micro Female PinboardThe included pin headers can be used for the parts below
22R1, R4330 ohm RResistor (1/4 Watt)

A decent assortment kit is here
Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal
32R2, R3270 ohm RResistor (1/4 Watt)Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal
43Shutter1, Strobe1, Sys1_GND1~<These are just test-point holes to solder test wires into>TestPoint:TestPoint_THTPad_2.5x2.5mm_Drill1.2mm
51Sys1_Conn1~4 Pin HeaderConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical
61Sys2_Conn1~3 Pin HeaderConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical
72U2, U3H11L1Isolator:H11L1Package_DIP:DIP-6_W7.62mm
81U474HC0474xx:74HC04Package_DIP:DIP-14_W7.62mm_Socket
91U5~Dual_Mos_Driver_ModuleVerdant_Custom_Footprint_Library:PCB Dual MOS Driver Module
22.5M Bolt

2.5M Nut
These help mechanically tie down the USB-B power connector to the board
26 - pin DIP socket<Optional>

A decent assortment kit is here
The opto-isolators and the hex inverter chip are the most likely to be blown up or injured by solder over-temps. So best to put them in sockets.
114 - pin DIP socket

<Optional>
<Optional>

Note: A 5V USB-B power supply with a male micro-USB connector is currently necessary to run the board. The supply is used as an isolated, independent (downstream of a transformer) power plane to try to keep the Pi’s and the Pi Camera safe.

Final view of top/bottom of completed PCB:

image

image

NOTE: Don’t be like the people who made the above boards. For example, use flux-cleaner to get rid of the excess flux when you are done!

Assembly Notes (see supporting images of the board):

  1. If desired (we suggest it), solder the two 6-Pin DIP sockets and one 14 pin DIP socket for the H11 opto-isolators and the 740s4 hex inverter.
  2. Use the two 2.5M bolts and nuts (nuts on the bottom of the PCB) to secure the USB board to the lower-left corner. Strip 1” of a thin wire bare and cut in two half-inch pieces that will fit through the VCC and GND holes of the USB board and through the back of the Connector Board PCB. Bend the ends to hold the wires in place and solder and trim.
  3. Solder a header pin post (see picture) into the GND and TRIG holes on the left side of the Dual MOS Driver Module so that at least 2mm of pin sticks out the bottom. Using these headers makes it easier to test-probe the trigger signal. Then insert the lower parts of the pins (as well as the four parts of the pins sticking out below the screw terminals) into the Connector Board PCB and solder. Alternatively, the same wire-through-the component-and-board technique used for the USB board can be used here. The four terminals below the screw terminals are not electrically important for the PCB, but soldering them helps mechanically secure the Dual-MOS switching component.
  4. It is useful (but not necessary) to solder three wires to the test ports on the left of the PCB. When something is not working, the ability to hook an oscilloscope up to these ports is important. If you strip the wires on the other end away from the board, make sure you protect them from accidentally contacting other component. These plugs can be used for that purpose.
  5. Attach the 12V input and output wire pairs to the Dual MOS component’s screw terminals. It’s best NOT to tin the ends, as the terminals seem to make better contact that way. Add some plugs (e.g., Ideal Industries 30-102 Power Plug.) to the ends of the leads to make it easier to connect/disconnect them later to the strobe and the LED power supply. The use of different ends for input and output (e.g., one male, one female) may make it more difficult to later plug these in wrong (output to input)!

Parts

14
QtyValueFootprintReferences
10VSMA1085400Pi Connector Parts:VSMA1085400D6, D7, D8, D9, D10, D11, D12, D13, D14, D15
2MountingHoleMountingHole:MountingHole_3.2mm_M3H6, H7
2MountingHole_PadMountingHole:MountingHole_2.2mm_M2_PadH5, H8

More from PiTracLM/PiTrac

4
  • 2 layers60 × 126.6 mmV3 Connector + IRLED, the printed circuit board in 3D

    V3 Connector + IRLED

    PiTracLM/PiTrac

    Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)

    151 parts439GPL-2.0
  • 2 layers60 × 100 mmPiTrac Pi Connector, the printed circuit board in 3D

    PiTrac Pi Connector

    PiTracLM/PiTrac

    Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)

    98 parts439GPL-2.0
  • 2 layers60 × 100 mmV3 Connector Only, the printed circuit board in 3D

    V3 Connector Only

    PiTracLM/PiTrac

    Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)

    65 parts439GPL-2.0
  • 2 layers70 × 50 mmPiTrac Connector Board, the printed circuit board in 3D

    PiTrac Connector Board

    PiTracLM/PiTrac

    Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)

    18 parts439GPL-2.0

Similar boards

  • 2 layers116.8 × 30 mmType d, the printed circuit board in 3D

    Type d

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    14 parts3kApache-2.0
  • 2 layers32 × 22 mmDiff driver, the printed circuit board in 3D

    Diff driver

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    14 parts990GPL-3.0
  • 2 layers34 × 45 mm2032Charger, the printed circuit board in 3D

    2032Charger

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    14 parts915
  • 2 layers34 × 109.9 mmTdisplay s3, the printed circuit board in 3D

    Tdisplay s3

    landonr/homeThing

    Wifi Smart Home Remotes that run on ESPHome

    14 parts551GPL-3.0
  • 2 layers45.3 × 42.7 mmMainPcb, the printed circuit board in 3D

    MainPcb

    adamb314/ServoProject

    Getting the most out of your hobby servo

    14 parts545
  • 2 layers42.5 × 28.8 mmC5VRX JACK DIY, the printed circuit board in 3D

    C5VRX JACK DIY

    Twotoz/C5VRX

    Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS

    14 parts515GPL-3.0
  • 2 layers62 × 24 mmMai button, the printed circuit board in 3D

    Mai button

    whowechina/mai_pico

    Pico controller for Maimai

    14 parts475

Questions

How big is the IRLED Only PCB?

It measures 35 × 25 mm and has 2 copper layers, 0.81 mm thick.

What parts does the IRLED Only use?

14 parts, built around the VSMA1085400. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the IRLED Only KiCad files?

From the PiTracLM/PiTrac repository on GitHub, at the commit this page was made from: the board is Hardware/KiCad Source Files/IRLED Only.kicad_pcb and its schematic Hardware/Archive/Connector Board v0.2/PiTrac Connector Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the IRLED Only design in my own project?

Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).