

- Size
- 46.1 × 83.1 mm
- Copper layers
- 2
- Thickness
- 0.79 mm
- Parts
- 58
- Nets
- 184
- Pads
- 596
- Tracks, vias
- 1,447, 160
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 29 May 2020
- Updated
- 2 Jun 2025
Overview
Spock is an open-source printed circuit board by PisterLab, from the PisterLab/scum-dev-board repository on GitHub. It is a 2-layer board of 46.1 × 83.1 mm with 58 parts on 184 nets, routed with 1,447 tracks and 160 vias.
It is built around the FT231XS-U, S-85S1AB10-I6T1U and S-85S1AB15-I6T1U, with the S-85S1AB18-I6T1U, 74AVC1T45GS-Q100H and ICM-20948 among its other parts. Its parts include 18 capacitors, 15 ICs, 7 connectors, 5 inductors and 4 resistors.
Main components
9FT231XS-U
SSOP-20-150mil-40℃~+85℃ 125uA 5V 8mA USB 2.0 USB to UART SSOP-20-150mil USB Converters ROHSFTDIUSB ConvertersS-85S1AB10-I6T1U
SNT-6A-40℃~+85℃ 1 1MHz 1V 2.2V~5.5V 200mA Buck Buck Built-in Yes SNT-6A DC-DC Converters ROHSABLICDC-DC ConvertersS-85S1AB15-I6T1U
SNT-6A-40℃~+85℃ 1 1.5V 1MHz 2.2V~5.5V 200mA Buck Buck Built-in Fixed Yes SNT-6A DC-DC Converters ROHSABLICDC-DC ConvertersS-85S1AB18-I6T1U
SNT-6A-40℃~+85℃ 1 1.8V 1MHz 2.2V~5.5V 200mA 260nA Buck Buck Built-in Fixed Yes SNT-6A DC-DC Converters ROHSABLICDC-DC Converters74AVC1T45GS-Q100H
XSON-6(1x1.5)-40℃~+125℃ 1 1 500Mbps 800mV~3.6V 800mV~3.6V Bidirectional Tri-State XSON-6(1x1.5) Translators, Level Shifters ROHSNexperiaTranslators, Level ShiftersICM-20948
QFN-24(3x3)-40℃~+85℃ 0.5KB 1.71V~3.6V 16bit 8uA Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24(3x3) Accelerometers ROHSTDK InvenSenseAccelerometers2450AT45A100E
SMD,9.5x2mm-40℃~+125℃ 1.2mm 1.3dBi、1.5dBi、2.2dBi 100MHz 2.4GHz 2mm 3W 50Ω 9.5mm Patch Antenna SMD,9.5x2mm Antennas ROHSJohanson DielectricsAntennasCONSMA001-G
插件Coaxial Connectors (RF)LinxHZ0805E601R-10
0805-40℃~+125℃ 1 300mΩ 500mA 600Ω@100MHz 0805 Ferrite Beads ROHSLairdFerrite Beads
README
sulu-ldo/readme.md

Update from board review 2021.04.27
- Put the antenna on a solo pin
- rearrange some pins
- change through hole size to 15 mils
- nrf pin labels
Updates 2021.04.25
- New layout for compatibility with NRF
- Bunch of through holes for emergency connections
- Return of the 2986 battery clip
Updates 2021.04.14
- Austin’s requested layout
- Larger dimensions -- no longers square
- 0.1” pins
- Pins for all GPIOs
- Antenna pin
- Removed I2C for IMU
- Via holes for wiring
- 2 layer instead of 4 layer
- HARD_RESET pin
- GPO_ZERO pin instead of LED
- Swapped GPIO 12 and GPIO 13 on IMU
- Consolidated headers
- Neatened labels
- New battery clip
Updates 2020.12.05
- removed zener diode
- added GPIOs 8, 9, 10
- added ground connections near GPIO
- added labels
- moved passives around
- added ADC pins
Updates 2020.12.02
- Replaced antenna header with VDDD
- Kept LED
- 0-80 standoffs
- 0.1” -> 0.05” headers
- Removed GPIO 8-15 pins
Updates 2020.10.07
- 30mm x 30 mm
- holes for standoffs
- SR521SW battery clip
- IMU
- GPIO, 3WB, UART, VBAT, VDDIO pins
- 1.8 V Zener diode for voltage protection
- LED programming indicator
Updates 2021.01.15
- Added missing BOOT_SOURCE_SEL header
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C3, C5, C6, C7, C26, C27 |
| 6 | 10 uF | Capacitor_SMD:C_0402_1005Metric | C8, C9, C12, C23, C25, C28 |
| 6 | 74AVCH4T245D,118 | downloaded_libs:SOIC127P600X175-16N | U9, U10, U11, U13, U14, U15 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 3 | 2.2 uH | Inductor_SMD:L_0402_1005Metric | L2, L3, L5 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | 270 | Resistor_SMD:R_0402_1005Metric | R1, R4 |
| 2 | 47pF | Capacitor_SMD:C_0402_1005Metric | C10, C11 |
| 2 | 74AVC1T45GS-Q100H | SamacSys_Parts:74LVC1G3157GS132 | U3, U4 |
| 2 | LED | LED_SMD:LED_0402_1005Metric | D1, D2 |
| 2 | LOGO | SCUM:BSAC | G***, G*** |
| 1 | 1.5 pF | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 1050170001 | SCUM:MOLEX_1050170001 | J5 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | 2450AT45A100E | downloaded_libs:ANT_2450AT45A100E | E1 |
| 1 | 3.9 nH | Inductor_SMD:L_0402_1005Metric | L4 |
| 1 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C4 |
| 1 | C | Capacitor_SMD:C_0402_1005Metric | C13 |
| 1 | CONSMA001-G | downloaded_libs:LINX_CONSMA001-G | J1 |
| 1 | Conn_01x24 | Connector_PinSocket_2.54mm:PinSocket_1x24_P2.54mm_Vertical | J6 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J9 |
| 1 | Conn_02x04_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J2 |
| 1 | Conn_02x10_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J3 |
| 1 | Conn_02x13_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x13_P2.54mm_Vertical | J4 |
| 1 | FT231XS-U | Package_SO:SSOP-20_3.9x8.7mm_P0.635mm | U2 |
| 1 | HZ0805E601R-10 | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | ICM-20948 | downloaded_libs:QFN40P300X300X105-24N | U5 |
| 1 | Perfboard | SCUM:Perfboard | U1 |
| 1 | S-85S1AB10-I6T1U | downloaded_libs:SOFL50P180X50-6N | U6 |
| 1 | S-85S1AB15-I6T1U | downloaded_libs:SOFL50P180X50-6N | U7 |
| 1 | S-85S1AB18-I6T1U | downloaded_libs:SOFL50P180X50-6N | U12 |
| 1 | scum3 | SCUM:QFN-100_EP_12x12_Pitch0.4mm | U8 |
More from PisterLab/scum-dev-board
8- 2 layers41.7 × 73.2 mm

- 6 layers36.3 × 46 mm

- 2 layers142.2 × 96.5 mm

- 2 layers41.7 × 36.1 mm

- 2 layers41.7 × 36.1 mm

- 2 layers42.5 × 34.3 mm

- 2 layers41.4 × 35.1 mm

- 2 layers46 × 59 mm

Similar boards
- 4 layers40 × 17.6 mm

- 4 layers40 × 100 mm

ASK
Tanki777/telecomlab_fso
The flowgraphs transmit a random source, which are bytes with values between 0 and 255. A random sequence of 30,000 bytes is sent and repeated while the flowgraph is running.
83 partsGPL-3.0 - 2 layers40 × 25 mm

FIC-100A
Reemuson/FIC-100A
USB IR Adapter compatible with Fluke 287 and 289 series multimeters
40 parts1CERN-OHL-W-2.0 - 4 layers86.3 × 25 mm

- 2 layers80 × 25 mm

RedPink STM32C09 Board
ARMontt/RedPink-CAN-USB
Device for Industrial - Automotive development
39 partsCC0-1.0 - 4 layers159 × 132.3 mm

- 4 layers120 × 75 mm

Current Sources Improved
mjmorano/Precision-Current-Source
Once it's uploaded connect the Arduino pins to the 6 pin header on the current source as follows:
95 parts - 4 layers82.8 × 88.9 mm

Metal detector test
bobasaurus/lumber-plunder-metal-detector
A VLF induction balance metal detector with a wooden body
111 parts11GPL-3.0
Questions
How big is the Spock PCB?
It measures 46.1 × 83.1 mm and has 2 copper layers, 0.79 mm thick.
What parts does the Spock use?
58 parts, built around the FT231XS-U, S-85S1AB10-I6T1U, S-85S1AB15-I6T1U and S-85S1AB18-I6T1U. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Spock KiCad files?
From the PisterLab/scum-dev-board repository on GitHub, at the commit this page was made from: the board is spock/Spock.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Spock design in my own project?
Its repository states no licence, so its author keeps all rights: ask PisterLab before reusing the design.