Skip to the content
4 layers65 × 30 mmLittle witch, the printed circuit board in 3D

The Little WitCH is a tiny but capable dev board for the WCH32V307, boasting:

Size
65 × 30 mm
Copper layers
4
Thickness
1.59 mm
Parts
73
Nets
93
Pads
338
Tracks, vias
1,415, 167
Pours
61
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
28 Apr 2026
Updated
30 Jul 2026

Overview

Little witch is an open-source printed circuit board by pianohacker, from the pianohacker/little-witch repository on GitHub. It is a 4-layer board of 65 × 30 mm with 73 parts on 93 nets, routed with 1,415 tracks and 167 vias.

It is built around the LM66100DCK and SIT8008BI-73-33N-25.000000. Its parts include 24 capacitors, 22 resistors, 4 ICs, 4 connectors and 2 diodes. It belongs with the RISC-V boards of this library.

Main components

2

README

README.md

Little WitCH

The Little WitCH is a tiny but capable dev board for the WCH32V307, boasting:

  • The WCH32V307 itself, with a single RISC-V RV32IMACF core
  • Gigabit Ethernet via the MXL86110C PHY
  • Raspberry-Pi-compatible I/O (with caveats), exposing:
    • Two SPI buses
    • Two I2C buses
    • PCM audio out
    • SDIO/eMMC
    • and/or 28 3.3V GPIO pins
  • USB-C 2.0
  • USB-1.1 via Raspberry-Pi-Zero-compatible test points
  • Tag-Connect TC2030 SWD debugging

Raspberry Pi compatibility

The WCH32V307's pin remapping can't make it a perfect match for the Raspberry Pi's peripherals. The biggest caveat is the SPI and PCM outputs, which are all multiplexed together and overlapping:

  • SPI3 is exposed on the same pins as the Pi's SPI0 bus.
  • PCM is exposed on the same pins as the Pi, but only supports output.
  • SPI2 can be exposed on the same pins as the Pi's SPI1 bus, but these pins overlap with the MDIO bus of the Ethernet PHY. Also, as these pins overlap with the PCM pins, SPI2 must be switched to by cutting and resoldering three solder jumpers below the USB-C port.

That said, this should still allow compatibility with a wide number of Pi Zero / Pi 4 HATs. Will mention specific examples here as they are tested.

Solder jumper reconfiguration

There are three sets of solder jumpers that can modify the behavior of this board:

  • The jumpers mentioned above, which collectively switch pins 12, 35, and 40 between SPI2 and PCM (via I2S3). These default to PCM. Note: to be explicit, to switch to SPI2 on these pins, the bridge between the first two pads of all three jumpers must be cut and the 2nd and 3rd jumpers solder-bridged.
  • A jumper to set the value of BOOT1. This defaults to 0.
  • A jumper to enable the power LED, which defaults to lit.

Authors

This is a collaboration between Jesse Weaver (pianohacker) and Pikkolo Assembly.

License

Little WitCH © 2026 by Jesse Weaver is licensed under CC BY-NC-SA 4.0. To view a copy of this license, visit https://creativecommons.org/licenses/by-nc-sa/4.0/

Parts

73
QtyValueFootprintReferences
18100nCapacitor_SMD:C_0402_1005MetricC2, C3, C4, C5, C6, C11, C14, C16, C18, C19, C20, C22, C23, C24, C26, C27 +2
71KCapacitor_SMD:C_0402_1005MetricR5, R17, R18, R19, R20, R21, R22
4MountingHole_PadMountingHole:MountingHole_2.7mm_M2.5_PadH1, H2, H3, H4
310uCapacitor_Tantalum_SMD:CP_EIA-2012-12_Kemet-RC1, C7, C10
34.7KCapacitor_SMD:C_0402_1005MetricR14, R15, R16
2100Capacitor_SMD:C_0402_1005MetricR11, R12
210kResistor_SMD:R_0402_1005MetricR7, R25
25.1kResistor_SMD:R_0402_1005MetricR8, R9
1100Resistor_SMD:R_0402_1005MetricR27
1100K ±1%Resistor_SMD:R_0603_1608MetricR24
1100kResistor_SMD:R_0402_1005MetricR10
11uCapacitor_SMD:C_0402_1005MetricC15
11uInductor_SMD:L_1008_2520MetricL1
12.49K ±1%Resistor_SMD:R_0402_1005MetricR13
122uCapacitor_SMD:C_0805_2012MetricC13
1260Resistor_SMD:R_0402_1005MetricR26
14.7uCapacitor_SMD:C_0805_2012MetricC12
1453K ±1%Resistor_SMD:R_0603_1608MetricR23
1BOOT0Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2SW2
1BOOT1Library:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_DotJP7
1CH32V307Package_QFP:LQFP-64_10x10mm_P0.5mmU1
1Conn_ARM_SWD_TagConnect_TC2030-NLConnector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_VerticalJ3
1GCT-USB4105Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_HorizontalJ4
1GNDTestPoint:TestPoint_Pad_D2.0mmTP1
1GPIO12Library:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_DotJP1
1GPIO35Library:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_DotJP2
1GPIO40Library:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_DotJP6
1LEDLED_SMD:LED_0603_1608MetricD3
1LM66100DCKPackage_TO_SOT_SMD:SOT-363_SC-70-6U4
1MXL86110C-AQB-RLibrary:QFN40_5X5_MXLU2
1P. LEDJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP5
1POWERLED_SMD:LED_0603_1608MetricD2
1RESETButton_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2SW1
1RPI GPIOConnector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_VerticalJ5
1SIT8008BI-73-33N-25.000000Oscillator:Oscillator_SMD_SiT_PQFN-4Pin_2.0x1.6mmY1
1TMJG0803HENLLibrary:RJ45_TMJG0803HENLJ2
1TPS62A0568PDRLRPackage_TO_SOT_SMD:SOT-563U3
1USB1_DNTestPoint:TestPoint_Pad_D1.5mmTP2
1USB1_DPTestPoint:TestPoint_Pad_D1.5mmTP3
1VBUSTestPoint:TestPoint_Pad_D2.0mmTP4

Similar boards

  • 4 layers70 × 54 mmPicoLab, the printed circuit board in 3D

    PicoLab

    CoretechR/PicoLab

    Web-GUI Embedded Multitool

    285 parts327GPL-3.0
  • 4 layers91 × 53.1 mmNff pcb, the printed circuit board in 3D

    Nff pcb

    o7-machinehum/flipper-blackhat

    Linux based WiFi pentesting device for the Flipper Zero.

    184 parts300
  • 6 layers55 × 95 mmEcho r1-rev1, the printed circuit board in 3D

    Echo r1-rev1

    amachronic/echoplayer

    Echo - Open Hardware Music Player

    154 parts281CERN-OHL-S-2.0
  • 2 layers115.2 × 78.6 mmL0destar, the printed circuit board in 3D

    L0destar

    m4rkw/l0destar

    l0destar open-source tracker project

    164 parts43
  • 2 layers54 × 12.5 mmBrodBoost C2, the printed circuit board in 3D

    BrodBoost C2

    axiometa/BrodBoost-C2

    USB - C Breadboard Powersupply: BrodBoost-C

    31 parts36CERN-OHL-S-2.0
  • 4 layers112.1 × 102.1 mmWarpSE, the printed circuit board in 3D

    WarpSE

    garrettsworkshop/WarpSE

    WIP 25 MHz MC68HC000-based accelerator card for Macintosh SE

    146 parts26
  • 2 layers100 × 63.7 mmFcart, the printed circuit board in 3D

    Fcart

    hi0t/fcart

    Open source flash cartridge

    115 parts23GPL-3.0
  • 4 layers34.5 × 39 mmEpd watch, the printed circuit board in 3D

    Epd watch

    andr00d/epd_watch

    epd watch project

    63 parts18MIT

Questions

How big is the Little witch PCB?

It measures 65 × 30 mm and has 4 copper layers, 1.59 mm thick.

What parts does the Little witch use?

73 parts, built around the LM66100DCK and SIT8008BI-73-33N-25.000000. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Little witch KiCad files?

From the pianohacker/little-witch repository on GitHub, at the commit this page was made from: the board is little-witch.kicad_pcb and its schematic ethernet.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Little witch design in my own project?

Its repository states no licence, so its author keeps all rights: ask pianohacker before reusing the design.