

CloudTempSensor
Cloud-based (MQTT actually) Temperature Sensor using ESP and MCP9808
- Size
- 69.9 × 58.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 66
- Pads
- 200
- Tracks, vias
- 387, 30
- Pours
- 11
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 2 Apr 2017
- Updated
- 24 Sep 2018
Overview
CloudTempSensor is an open-source printed circuit board by penguineer, from the penguineer/CloudTempSensor repository on GitHub. It is a 2-layer board of 69.9 × 58.4 mm with 57 parts on 66 nets, routed with 387 tracks and 30 vias.
It is built around the ESP-12E, MCP9808-E/MS and LM1117-3.3, with the MCP23016-I/SO and WS2812 among its other parts. Its parts include 33 resistors, 7 capacitors, 5 connectors, 4 ICs and 3 diodes. It belongs with the ESP8266 boards of this library.
Main components
5ESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi ModulesMCP9808-E/MS
MSOP-8-40℃~+125℃ 13bit 2.7V~5.5V 250ms I2C、SMBus ±0.5℃ MSOP-8 Temperature Sensors ROHSMicrochip TechnologyTemperature SensorsLM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedMCP23016-I/SO
SOIC-28-300mil-40℃~+85℃ 16 25mA 25mA 25uA 2V~5.5V 400kHz 600mV 8 I2C Interrupt Output Reset function、Cascading and address extension SOIC-28-300mil I/O Expanders ROHSMicrochip TechnologyI/O ExpandersWS2812
SMD5050-4P1.57mm 1000mcd 110mcd 120us 2kHz 3.7V~5.3V 300ns 320mcd 451nm 523nm 5mm 5mm 623nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit Top-mount SMD5050-4P RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 39R | Resistors_SMD:R_0603_HandSoldering | R2, R3, R4, R5, R6, R7, R8, R10, R11, R12, R13, R14, R15, R16, R17, R18 +1 |
| 9 | 10k | Resistors_SMD:R_0603_HandSoldering | R19, R20, R21, R22, R26, R27, R28, R31, R32 |
| 4 | 330R | Resistors_SMD:R_0603_HandSoldering | R24, R25, R29, R30 |
| 3 | 100n | Capacitors_SMD:C_0603_HandSoldering | C1, C5, C6 |
| 2 | 22µ | Capacitors_SMD:C_1206_HandSoldering | C4, C7 |
| 2 | SW_SPST | Buttons_Switches_SMD:SW_SPST_EVQPE1 | SW1, SW2 |
| 1 | 0 | Resistors_SMD:R_0603_HandSoldering | R33 |
| 1 | 10µ | Capacitors_SMD:C_1206_HandSoldering | C3 |
| 1 | 150R | Resistors_SMD:R_0603_HandSoldering | R23 |
| 1 | 33p | Capacitors_SMD:C_0603_HandSoldering | C2 |
| 1 | 3k9 | Resistors_SMD:R_0603_HandSoldering | R1 |
| 1 | CONN_01X03 | Pin_Headers:Pin_Header_Straight_1x03 | P4 |
| 1 | CONN_01X05 | Socket_Strips:Socket_Strip_Straight_1x05 | P2 |
| 1 | CONN_01X06 | Socket_Strips:Socket_Strip_Straight_1x06 | P3 |
| 1 | ESP-12E | ESP8266:ESP-12E | U4 |
| 1 | LM1117-3.3 | TO_SOT_Packages_SMD:SOT-223 | U2 |
| 1 | MCP23016 | Housings_SOIC:SOIC-28W_7.5x17.9mm_Pitch1.27mm | U1 |
| 1 | MCP9808 | Housings_SSOP:MSOP-8_3x3mm_Pitch0.65mm | U3 |
| 1 | Screw_Terminal_1x02 | n39-kicad:AKL_101-02 | J1 |
| 1 | USB_B | Connect:USB_Micro-B | P1 |
| 1 | VQE24 | n39-kicad:VQE24 | D1 |
| 1 | WS2812 | LEDs:LED_WS2812-PLCC6 | D3 |
| 1 | gn | LEDs:LED_1206 | D2 |
The 54 most common of 57 parts.
Similar boards
- 2 layers76.3 × 50.3 mm

- 2 layers129.5 × 106.7 mm

Buttonarray
Mission-DMX/hardware
This repository contains documentations, pcb designs and fpga designs of the console
103 parts - 2 layers49.5 × 30 mm

- 2 layers120 × 90 mm

- 2 layers33.7 × 97.8 mm

HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470 - 2 layers43 × 34.3 mm

- 2 layers47 × 37.5 mm

- 2 layers60 × 40 mm

Forcegauge
szbeni/forcegauge
Traning for climbing. Load cell with HX711 and real time plotting,
77 parts18GPL-3.0
Questions
How big is the CloudTempSensor PCB?
It measures 69.9 × 58.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the CloudTempSensor use?
57 parts, built around the ESP-12E, MCP9808-E/MS, LM1117-3.3 and MCP23016-I/SO. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CloudTempSensor KiCad files?
From the penguineer/CloudTempSensor repository on GitHub, at the commit this page was made from: the board is Board/Board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the CloudTempSensor design in my own project?
Its repository states no licence, so its author keeps all rights: ask penguineer before reusing the design.