
EINK DEV OLD PCB
p01t3rge1st/EINK_STM32
Projekt E-INK AiR 2025. Kod oraz schematy zostają umieszczone tutaj.

Projekt E-INK AiR 2025. Kod oraz schematy zostają umieszczone tutaj.
EINK DEV is an open-source printed circuit board by p01t3rge1st, from the p01t3rge1st/EINK_STM32 repository on GitHub. It is a 4-layer board of 79.5 × 53.3 mm with 80 parts on 95 nets, routed with 618 tracks and 85 vias.
It is built around the STM32WB55CEU6, MIC5219-3.3YMM and TP4056-42-ESOP8, with the SI1304BDL among its other parts. Its parts include 32 capacitors, 18 resistors, 10 connectors, 6 diodes and 4 inductors. It belongs with the lEDs and displays boards and the STM32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100n | Capacitor_SMD:C_0603_1608Metric | C14, C15, C16, C17, C18, C20, C21, C23, C24, C30 |
| 7 | 1u | Capacitor_SMD:C_0603_1608Metric | C1, C2, C5, C7, C8, C9, C10 |
| 4 | 10u | Capacitor_SMD:C_0603_1608Metric | C11, C12, C31, C32 |
| 4 | 220R | Resistor_SMD:R_0603_1608Metric | R11, R16, R17, R18 |
| 4 | R | Resistor_SMD:R_0603_1608Metric | R1, R6, R7, R8 |
| 3 | 220 | Resistor_SMD:R_0603_1608Metric | R12, R13, R15 |
| 3 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C19, C22, C25 |
| 3 | D | Diode_SMD:D_0603_1608Metric | D1, D2, D3 |
| 3 | LED | LED_SMD:LED_0603_1608Metric | D4, D5, D6 |
| 2 | 0p3 | Capacitor_SMD:C_0603_1608Metric | C28, C29 |
| 2 | 10p | Capacitor_SMD:C_0603_1608Metric | C26, C27 |
| 2 | 10u | Inductor_SMD:L_0603_1608Metric | L2, L3 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C3, C6 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 1 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C33 |
| 1 | 2,4Ghz LP 50Ohm | Filter:Filter_Mini-Circuits_FV1206 | FL1 |
| 1 | 2n7 | Inductor_SMD:L_0603_1608Metric | L4 |
| 1 | 32Mhz | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y2 |
| 1 | 32kHz768 | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm | Y1 |
| 1 | 400 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 5100 | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | Conn_01x02 | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J3 |
| 1 | Conn_01x03 | Connector:FanPinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | Conn_ARM_SWD_TagConnect_TC2030 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | Conn_Coaxial | Connector_Coaxial:U.FL_Hirose_U.FL-R-SMT-1_Vertical | J7 |
| 1 | FPC | Connector_FFC-FPC:TE_2-1734839-4_1x24-1MP_P0.5mm_Horizontal | J1 |
| 1 | Jumper_3_Bridged12 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | L | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | LOW POWER UART | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | MIC5219-3.3YMM | Package_SO:MSOP-8_3x3mm_P0.65mm | U3 |
| 1 | R2 | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | STM32WB55CEU6 | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | Si1304BDL | footprints:SC-70_SI1_VIS | Q1 |
| 1 | TP4056-42-ESOP8 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U2 |
| 1 | Thermistor_NTC | Resistor_SMD:R_0603_1608Metric | TH1 |
| 1 | UART1 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | USB_C_Plug_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | P1 |
| 1 | USER1 | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J8 |
| 1 | USER2 | Button_Switch_THT:SW_DIP_SPSTx03_Slide_6.7x9.18mm_W7.62mm_P2.54mm_LowProfile | J9 |
| 1 | uF | Capacitor_SMD:C_0603_1608Metric | C4 |

p01t3rge1st/EINK_STM32
Projekt E-INK AiR 2025. Kod oraz schematy zostają umieszczone tutaj.

FeatureNAB/air-sensor
Smart Air Quality Sensor built using ESP32, SEN66 and ESPHome



chimmmmy/echain
software to control a smart keychain with an e ink display, powered by seed studio nrf52840

ANSHUMANDOCX/ESP32-Weather-Dashboard
ESP32 weather dashboard using a 3.7 inch eink display

Outdatedcandy92/ESP32-Eink
A tiny E-Ink display driver board featuring an ESP32-C3 and an onboard battery charging IC. It wirelessly drives a 2.13-inch E-Ink display and is designed for portable, ultra-low-power projects such as status displays…


It measures 79.5 × 53.3 mm and has 4 copper layers, 1.6 mm thick.
80 parts, built around the STM32WB55CEU6, MIC5219-3.3YMM, TP4056-42-ESOP8 and SI1304BDL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the p01t3rge1st/EINK_STM32 repository on GitHub, at the commit this page was made from: the board is EINK_DEV.kicad_pcb and its schematic EINK_DEV.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask p01t3rge1st before reusing the design.