

OSHE RadarDetector ControlBoard
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 44
- Nets
- 108
- Pads
- 223
- Tracks, vias
- 338, 30
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 10 Jan 2026
- Updated
- 23 Apr 2026
Overview
OSHE RadarDetector ControlBoard is an open-source printed circuit board by OSHE-Github, from the OSHE-Github/Radar-Detector repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 100 × 100 mm with 44 parts on 108 nets, routed with 338 tracks and 30 vias.
It is built around the MPM3804GG-Z, TEENSY 4.1 and TL072IP, with the ICL7660CBAZ, LM337TG and C503B-GCN-CY0C0791 among its other parts. Its parts include 16 resistors, 12 capacitors, 6 ICs, 5 connectors and 1 diode. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
9MPM3804GG-Z
QFN-10(2x2)-40℃~+125℃ 0.9mm 1 11uA 2.3V~5.5V 2.4MHz 2mm 2mm 600mA 600mV~5.5V 91% Buck Short Circuit Protection、Overheat protection QFN-10(2x2) DC-DC Power Modules ROHSMonolithic Power SystemsDC-DC Power ModulesTEENSY 4.1
Development Boards & Kits - ARM ModuleSparkFun ElectronicsUncategorisedTL072IP
PDIP-8-15V~-5V、5V~15V -40℃~+85℃ 1.4mA 100dB 13V/us 18nV/√Hz@1kHz 18uV/℃ 2 3MHz 3mV 5pA 65pA Short-Circuit Protection、Built-in compensation、Latch-up suppression PDIP-8 FET Input Amplifiers ROHSTexas InstrumentsFET Input AmplifiersICL7660CBAZ
SOP-8Cascade support、Charge pump / inverting topology switching、Adaptive switching frequency SOP-8 Charge Pumps ROHSRenesas ElectronicsCharge PumpsLM337TG
TO-220AB0.003%Vout 0℃~+125℃@(Tj) 1 1.2V~37V 1.5A 40V 77dB@(120Hz) Adjustable Negative Over Current Protection、Over Temperature Protection、Short Circuit Protection TO-220AB Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiDropout Regulators(LDO)C503B-GCN-CY0C0791
插件,D=5mmLED Indication - DiscreteCree LEDLM317LZ
TO-92-40℃~+125℃@(Tj) 1 1.2V~37V 100mA 40V 80dB@(120Hz) Adjustable Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-92 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSMF5.0A
SOD-123FLESD And Surge Protection (TVS/ESD)hongjiachengUSB4125-GF-A-0190
SMD-30℃~+85℃ 1 20 thousand cycles 3A 48V 6P Black Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB Connectors
README
README.mdRadar-Detector
Project Details
a fully open-source radar detector that can be easily replicated by others. Unlike existing commercial solutions, which are proprietary, this design will provide transparency, customization, and accessibility to users. By creating the first truly open-source radar detector, the project expands available options for individuals interested in building, modifying, or better understanding radar detection technology.
This device is powered by the 12V port that's in every commercial vehicle by using a 5V adapter and USB-C connector on board.
Current State
The current Design includes
- Completed RF and Control Board
- Completed Antenna and Waveguide
- A breadboarded circuit for K band detection
Semester End Report
For the Enterprise Program at Michigan Tech there is a end of semester report for the project to summarize the progress of the project. Link
Relevant Standards
- Traces Were sized appropriately for current being drawn
- No traces can be ran under the main RF lines
- There was fusing put in front of the main power input from the USB-C
- Decoupling capacitors used to reduce noise from voltage sources going into sensitive components
Constraints of Design
- when working with high frequencies up to 40GHz you have to use special small components that can handle it
- The material to make a PCB that can handle that high of frequencies is very expensive
- Amplifiers for this frequency are very expensive
Next Semester Goals
- Look into possible cheaper solutions using modules like what we found for the K band
- Test the Ka band implementation once we have the antenna
- Look into the design on the component for the K band and see if parts of it are re-creatable
Parts
44| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0.1μF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C7, C11, C13, C14 |
| 4 | 240 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R10, R11, R13 |
| 2 | 100K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R7 |
| 2 | 10μF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C9, C10 |
| 2 | 10μF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 2 | 1μF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C8, C12 |
| 2 | 200K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4, R6 |
| 2 | 22μF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | C503B-GCN-CY0C0791 | footprints:C503B | CR1, CR3 |
| 2 | Conn_01x09 | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J3, J5 |
| 2 | Conn_01x11 | Connector_PinHeader_2.54mm:PinHeader_1x11_P2.54mm_Vertical | J4, J5 |
| 2 | MPM3804GG-Z | footprints:QFN2p0x2p0x0p9_MNP | U2, U3 |
| 1 | 143 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R14 |
| 1 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R16 |
| 1 | 330 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R12 |
| 1 | 35.7K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5 |
| 1 | 3A | Fuse:Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F1 |
| 1 | 3k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R15 |
| 1 | 44.2K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R8 |
| 1 | ICL7660CBAZ | footprints_NEW:SOIC8_4X5_INR | U4 |
| 1 | LM317LZ | footprints_NEW:TO-92_STM | CR2 |
| 1 | LM337TG | footprints_NEW:TO220AB-3_ONS | U5 |
| 1 | SMF5.0A | ALL NEW Footprints and schematic:TVS_SMF5.0A | D1 |
| 1 | TL072IP | footprints_NEW:P8 | U6 |
| 1 | Teensy4.1 | footprints_NEW:Teensy41 | U1 |
| 1 | USB4125-GF-A-0190 | footprints:CONN6_125-GF-A-0190_GCT | J1 |
More from OSHE-Github/Radar-Detector
1- 2 layers100 × 100 mm

Similar boards
- 8 layers50 × 50 mm

Omodri laas
open-dynamic-robot-initiative/open-motor-driver-initiative
Open-source drive for brushless motors, following the open dynamic robot initiative
265 parts122BSD-3-Clause - 4 layers100 × 70 mm

SEM
Serhio4522/SEM_hitachi-
Digitization of a Hitachi scanning electron microscope (SEM) — hardware design, FPGA firmware, and analog frontend schematics.
288 parts1 - 2 layers98.1 × 99.7 mm

- 2 layers42.1 × 40.9 mm

Atmega hooting wiring
PhysicsUofRAUI/hooting_owl
Hold code and eventually the pcb layout for my hooting owl retrofit
16 partsMIT - 2 layers97.8 × 57.8 mm

- 2 layers60 × 40 mm

Canary
offgridevices/offgrid-hardware
Open hardware from OffGrid Devices. One folder per board. CERN-OHL-S.
52 partsCERN-OHL-S-2.0 - 2 layers91.4 × 101.6 mm

Vector gen
qu1j0t3/vector_gen
In first version of PCB there is a bug that leaves U6 Vss/Vdd pins floating and U5 Vdd floating:
103 parts13 - 2 layers100 × 60 mm

Questions
How big is the OSHE RadarDetector ControlBoard PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the OSHE RadarDetector ControlBoard use?
44 parts, built around the MPM3804GG-Z, TEENSY 4.1, TL072IP and ICL7660CBAZ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the OSHE RadarDetector ControlBoard KiCad files?
From the OSHE-Github/Radar-Detector repository on GitHub, at the commit this page was made from: the board is Front-End KiCad/Radar_Detector/FINAL - LOWER OSHE CONTROL BOARD/OSHE_RadarDetector_ControlBoard.kicad_pcb and its schematic Front-End KiCad/Radar_Detector/FINAL - LOWER OSHE CONTROL BOARD/FINAL - LOWER OSHE CONTROL BOARD/OSHE_RadarDetector_ControlBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the OSHE RadarDetector ControlBoard design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).