4 layers115.5 × 96.2 mm
Closed deck x4
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
245 parts19
2 layers98.2 × 53.3 mm
Pre Ignition
OpenLogicEFI/Hardware19Hardware is based off an open source project called Speeduino by Josh Stewart.
- Size
- 98.2 × 53.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 102
- Nets
- 139
- Pads
- 395
- Tracks, vias
- 569, 168
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 29 Mar 2020
- Updated
- 19 Oct 2026
Overview
Pre Ignition is an open-source printed circuit board by OpenLogicEFI, from the OpenLogicEFI/Hardware repository on GitHub. It is a 2-layer board of 98.2 × 53.3 mm with 102 parts on 139 nets, routed with 569 tracks and 168 vias.
It is built around the TC4427EOA, SRV05-4-P-T7 and L78M05ABDT-TR, with the ULN2003A, 1N4148WS and AO3400A among its other parts. Its parts include 40 resistors, 28 capacitors, 7 ICs, 7 connectors and 5 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
8
TC4427EOA
SOIC-8-40℃~+85℃ 1.5A 1.5A 19ns 19ns 2 2.4V 4.5V~18V 400uA 800mV MOSFET SOIC-8 Gate Drivers ROHSMicrochip TechnologyGate Drivers
SRV05-4-P-T7
SOT-23-612V 1A@8/20us 3.5pF 500W@8/20us 5V 5uA 6V ESD Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSPROTEKESD And Surge Protection (TVS/ESD)
L78M05ABDT-TR
TO-252-2(DPAK)-40℃~+125℃@(Tj) 1 2V@(350mA) 35V 40uV 500mA 5V 62dB@(120Hz) 6mA Fixed Over Temperature Protection、Short Circuit Protection Positive TO-252-2(DPAK) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
ULN2003A
SOP-16-40℃~+85℃ 0.93mA 100uA 15pF 20uA 30V 50V Seven channels SOP-16 Darlington Transistor Arrays ROHSUMWDarlington Transistor Arrays
1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes
AO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
B5819
SOD-523SOD-523 Schottky Diodes ROHSDongChenSchottky Diodes
ZMM5V6-MS
LL-341 Independent 100nA 25Ω 450Ω 5.2V~6V 5.6V 500mW LL-34 Zener Diodes ROHSMSKSEMIZener Diodes
README
README.mdOpenLogicEFI
Formerly: DetonationEMS
OpenLogicEFI ECU's are based off an open source project called Speeduino by Josh Stewart. Currently all released boards use official Speeduino firmware. In TunerStudio set to "Board Layout" to "Speeduino 0.4"
License
All designs are released under the TAPR Open Hardware License v1.0
Documentation
-
The Official Speeduino Manual, documents and discord are the best places to start.
Parts
102| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C3, C7, C10, C12, C14, C15, C16, C17, C19, C21, C22 |
| 10 | 1K | Resistor_SMD:R_0603_1608Metric | R1, R2, R4, R8, R10, R17, R18, R22, R26, R31 |
| 10 | 470 | Resistor_SMD:R_0603_1608Metric | R9, R12, R32, R33, R34, R35, R36, R37, R38, R40 |
| 8 | 220nF | Capacitor_SMD:C_0603_1608Metric | C4, C18, C20, C23, C24, C25, C27, C28 |
| 7 | 100K | Resistor_SMD:R_0603_1608Metric | R3, R5, R6, R14, R15, R16, R19 |
| 3 | 2.4k | Resistor_SMD:R_0603_1608Metric | R7, R20, R23 |
| 3 | SRV05-4-P-T7 | Package_TO_SOT_SMD:SOT-23-6 | U1, U4, U5 |
| 2 | 10 | Resistor_SMD:R_1206_3216Metric | R21, R24 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R11, R39 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C9, C11 |
| 2 | 2.49k | Resistor_SMD:R_0603_1608Metric | R27, R28 |
| 2 | Conn_01x04 | Misc:1X4-PROTO | J3, J6 |
| 2 | Conn_01x04 | Detonation:1x02-Proto | J2, J5 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | LED1, LED2 |
| 2 | Pullup | Detonation:1x02-Proto | JP1, JP2 |
| 2 | STP62NS04Z | Package_TO_SOT_THT:TO-220-3_Vertical | Q1, Q2 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C8 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R13 |
| 1 | 1N4148WS | Diode_SMD:D_SOD-323F | D2 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 2K | Resistor_SMD:R_0603_1608Metric | R25 |
| 1 | 3.9k | Resistor_SMD:R_0603_1608Metric | R29 |
| 1 | 330nF | Capacitor_SMD:C_1206_3216Metric | C6 |
| 1 | 330nF | Capacitor_SMD:C_0603_1608Metric | C26 |
| 1 | 47pF | Capacitor_SMD:C_0603_1608Metric | C13 |
| 1 | 51k | Resistor_SMD:R_0603_1608Metric | R30 |
| 1 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | Arduino_Mega2560_Shield-Arduino | MyLibs:Arduino_Mega2560_Shield_IO_Only_No_Silk_Screen | XA1 |
| 1 | B5819 | Diode_SMD:D_SOD-123 | D1 |
| 1 | Conn_01x04 | Detonation:1x1-GPIO | J7 |
| 1 | Conn_02x12_Counter_Clockwise | Connector_Molex:Molex_Micro-Fit_3.0_43045-2400_2x12_P3.00mm_Horizontal | J4 |
| 1 | Jumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP5 |
| 1 | L78M05ABDT-TR | Detonation:TO-252-2-Thermal | IC1 |
| 1 | LOGO | Detonation-Logos:Design by 25mm | G3 |
| 1 | Logo_Open_Hardware_Small | Detonation:Pre-Ignition-800 | G2 |
| 1 | Logo_Open_Hardware_Small | Detonation:SpeeduinoCompatible-17mm | G1 |
| 1 | MOV | Detonation:MOV07D220KTR | RV1 |
| 1 | MPXH6400 | Detonation:MPXH6250 | IC2 |
| 1 | Pololu_Breakout_DRV8825 | Detonation:DVR8825-Labeled-Front | A1 |
| 1 | TC4427 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | ULN2003A | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | VR-HALL | Misc:3x1-GPIO | JP3 |
| 1 | VR-Hall | Misc:3x1-GPIO | JP4 |
| 1 | VR_Header | Misc:DIP-8_W7.62mm_Socket_VRConditioner | J1 |
| 1 | ZMM5V6-M | Diode_SMD:D_MiniMELF | D3 |
| 1 | ~ | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP6 |
More from OpenLogicEFI/Hardware
12- 2 layers115.5 × 96.2 mm
Closed deck x4
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
223 parts19 - 2 layers98.8 × 69.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
167 parts19 - 2 layers100 × 99.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
166 parts19 - 4 layers98.8 × 69.8 mm
SparkGapX4
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
166 parts19 - 2 layers98.8 × 69.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
159 parts19 - 2 layers100 × 100 mm
1.3e
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
157 parts19 - 2 layers100 × 99.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
152 parts19 - 2 layers100 × 100 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
142 parts19 - 2 layers100 × 100 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
141 parts19 - 2 layers100 × 100 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
136 parts19 - 2 layers98.2 × 53.3 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
104 parts19
Similar boards
- 2 layers182.5 × 165 mm
Digital inputs
rusefi/stim
GPIO: output: x4 address pins output: x4 test control pins output: mux off
182 parts - 2 layers20 × 100 mm
- 4 layers243.8 × 171.5 mm
- 4 layers243.8 × 245.5 mm
Neotron Common Hardware
Neotron-Compute/Neotron-Common-Hardware
Contains KiCad footprints and symbols shared across multiple Neotron projects.
287 parts4CC-BY-SA-4.0 - 2 layers50 × 72 mm
- 4 layers243.8 × 171.5 mm
- 4 layers100 × 80 mm
- 4 layers164 × 118 mm
OpenEFI rev4 bkp
Churrosoft/OpenEFI-PCB
Coleccion de PCB y planos recomendados para montar una OpenEFI
345 parts8CERN-OHL-S-2.0
Questions
How big is the Pre Ignition PCB?
It measures 98.2 × 53.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pre Ignition use?
102 parts, built around the TC4427EOA, SRV05-4-P-T7, L78M05ABDT-TR and ULN2003A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pre Ignition KiCad files?
From the OpenLogicEFI/Hardware repository on GitHub, at the commit this page was made from: the board is Engine Managment/Pre-Ignition/Pre-Ignition x2/MX2B/Pre_Ignition.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pre Ignition design in my own project?
Its repository states no licence, so its author keeps all rights: ask OpenLogicEFI before reusing the design.