Skip to the content
2 layers81 × 34 mmCosin tag, the printed circuit board in 3D

KiCad PCB layouting workshop

Size
81 × 34 mm
Copper layers
2
Thickness
1.6 mm
Parts
65
Nets
18
Pads
147
Tracks, vias
470, 4
Routed
Yes
KiCad
KiCad 4
Created
11 Apr 2016
Updated
6 Jul 2016

Overview

Cosin tag is an open-source printed circuit board by onitake, from the onitake/pcb-workshop repository on GitHub. It is a 2-layer board of 81 × 34 mm with 65 parts on 18 nets, routed with 470 tracks and 4 vias.

Its parts include 49 diodes, 6 resistors, 5 transistors, 1 capacitor and 1 IC. It belongs with the AVR (ATmega, ATtiny) boards of this library.

README

README.md

PCB layouting workshop

These are the example files and a short presentation for an introduction to printed circuit board layouting with KiCad.

The design is loosely based on Larry Ogrodnek's nametag, with some modifications and enhancements. There's both through-hole and SMD versions. The THT version is designed for 5mm LEDs, thus making it very large. A new 3mm version is being worked on.

The software for the microcontroller is in a separate project.

You can also find an example for a LED dot matrix display tag. (currently broken, the pinout is wrong)

Description

The circuit is grouped in 4 parts:

  • 5 LED blocks
  • Transistor drivers for each block (based on 2N7002 N-FETs)
  • ATtiny13 microcontoller
  • CR2032 battery

Each block consists of a total of 20 LEDs in parallel, which can be soldered on as desired.

It should be noted that the CR2032 has a high internal resistance and can only deliver small currents, up to about 40mA.

The current-limiting resistors for each block should thus be adjusted accordingly, to prevent brown-out of the MCU. Note that the transistors also have a relatively high on resistance.

If a Li-Ion or LiPo battery is used instead of the button cell, much higher currents are possible.

The parts are fairly standard and can be ordered from any supplier, such as Farnell, DigiKey, Reichelt, ...

License

This documentation is copyright © 2016 by Chaostreff Basel and describes Open Hardware and is licensed under the CERN OHL v. 1.2. Please see the the LICENSE file for applicable conditions.

The author's contact information can be found in AUTHORS.

Parts

65
QtyValueFootprintReferences
49LEDLEDs:LED_0805D1, D2, D3, D10, D21, D22, D23, D24, D25, D26, D27, D28, D29, D30, D31, D32 +33
52N7002TO_SOT_Packages_SMD:SOT-23_HandsolderingQ1, Q2, Q3, Q4, Q5
310Resistors_SMD:R_0603_HandSolderingR1, R3, R5
1100kResistors_SMD:R_0603_HandSolderingR6
1100nResistors_SMD:R_1206_HandSolderingC2
124Resistors_SMD:R_0603_HandSolderingR4
13Vnametag:CR2032BT1
18.2Resistors_SMD:R_0603_HandSolderingR2
1ATTINY13-SSSMD_Packages:SOIC-8-NIC1
1ISPPin_Headers:Pin_Header_Straight_2x03P1
1RESETButtons_Switches_SMD:SW_SPST_EVQP0JP1

More from onitake/pcb-workshop

3
  • 2 layers89 × 35 mmNametag smd, the printed circuit board in 3D

    Nametag smd

    onitake/pcb-workshop

    KiCad PCB layouting workshop

    116 parts
  • 2 layers180 × 54 mmNametag, the printed circuit board in 3D

    Nametag

    onitake/pcb-workshop

    KiCad PCB layouting workshop

    116 parts
  • 2 layers84 × 60 mmMatrixtag, the printed circuit board in 3D

    Matrixtag

    onitake/pcb-workshop

    KiCad PCB layouting workshop

    24 parts

Similar boards

  • 2 layers42 × 67 mmLalboard, the printed circuit board in 3D

    Lalboard

    JesusFreke/lalboard

    A 3D-printed keyboard inspired by the DataHand

    65 parts993
  • 2 layers198.1 × 30.5 mmSplitflap driver, the printed circuit board in 3D

    Splitflap driver

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    65 parts744MIT
  • 2 layers74.8 × 32.5 mmMooltipass mini, the printed circuit board in 3D

    Mooltipass mini

    limpkin/mooltipass

    Github repository dedicated to the mooltipass project

    65 parts531
  • 2 layers60 × 100 mmV3 Connector Only, the printed circuit board in 3D

    V3 Connector Only

    PiTracLM/PiTrac

    Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)

    65 parts439GPL-2.0
  • 2 layers45 × 58.2 mmOpentama, the printed circuit board in 3D

    Opentama

    Sparkr-tech/opentama

    An open-source reference design for MCUGotchi

    65 parts237
  • 2 layers40 × 120 mmPhotodiode board v3, the printed circuit board in 3D

    Photodiode board v3

    0x23/nmWave-Interferometer

    An Open Source Interferometer for Accurate Distance Measurements

    65 parts151MIT
  • 2 layers78 × 130 mmLofence, the printed circuit board in 3D

    Lofence

    kiu/lofence

    LoFence is a LoRaWAN capable IoT electric fence monitoring system running on the The Things Network.

    65 parts142MIT

Questions

How big is the Cosin tag PCB?

It measures 81 × 34 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Cosin tag use?

65 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Cosin tag KiCad files?

From the onitake/pcb-workshop repository on GitHub, at the commit this page was made from: the board is cosin_tag.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Cosin tag design in my own project?

Its repository states no licence, so its author keeps all rights: ask onitake before reusing the design.