Skip to the content
2 layers100 × 100 mmParvus psu, the printed circuit board in 3D

TDA7293 based audio power amplifier

Size
100 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
67
Nets
30
Pads
148
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 5 (file 20171130)
Created
4 Feb 2018
Updated
18 Aug 2021

Overview

Parvus psu is an open-source printed circuit board by nradulovic, from the nradulovic/hw_parvus repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 100 × 100 mm with 67 parts on 30 nets.

It is built around the BC546B and BC556B. Its parts include 22 resistors, 15 capacitors, 9 connectors, 8 transistors and 7 diodes. It belongs with the audio and music and power boards of this library.

Main components

2

README

README.rst

.. contents:: Table of Contents :depth: 3

Introduction

This document shall describe rationales used to design and build audio power amplifier using TDA7293 integrated circuit.

Architecture

The amplifier architecture consists of the following sections:

The amplifier consists of the following section:

  • Amplifier (AMP) board (left and right channels)
  • Input/output filtering and Interface (IOI) board
  • Power supply and control (PSC) board

.. image:: images/board_overview.png

Each of these sections are implemented as a separate board.

Amplifier (AMP) board

Connections

The board features the following conntectors:

  • Power Supply Input - PSI: Vcc, GND, Vee
  • Speaker Output - SPO: Out, GND
  • Signal Input - SGI: In, SGND
  • Control and Mute Slave - CMS: Power sense, Mute, Clip, GND

.. image:: images/amp_symbol.png

3D Render with components

.. image:: images/3d_all.png

3D Render of board top layer

.. image:: images/3d_rendr_top.png

3D Render of board bottom layer

.. image:: images/3d_rendr_bottom.png

PCB Silkscreen plan

.. image:: images/pcb_silkscreen.png

Schematic

.. image:: images/schematic.png

Input low-pass filter

For input filter we choose the frequency between 300kHz and 400kHz::

text
    +---+ Rlp1    +---+ Rlp2
0---+   +----+----+   +---+---o Toward Amplifier IC block
    +---+    |    +---+   |
           ----- Clp1   ----- Clp2
           -----        -----
             |            |
            === Ground   === Ground

Using the 2nd order CR low-pass filter calculator at URL: http://sim.okawa-denshi.jp/en/CRCRtool.php we arrive at:

.. math::

text
Rlp1 = 100 Ohm, Rlp2 = 100 Ohm

Clp1 = 220pF,   Clp2 = 2.2nF

fp1 = 352kHz

fp2 = 14MHz

For more details please refer to: http://www.johnhearfield.com/RC/RC4.htm

The ground loop breaker resistor

A ground loop breaker resistor is located between SGND and GNDPWR grounds. The value of this resistor should be around 10 ohms.

Gain value

Using inverted topology since we want to reduce common mode distortion in the input stage. But in case of TDA7293 IC it is not easy to use inverted topology since the mute circuit is implemented on positive OPAMP input.

The equivalent gain circuit resistance needs to stay below 600ohms. This is so because all noise measurements in data-sheet were done with 600ohms or 0ohms.

Using low feedback gain is preferred for several reasons:

  • there is more loop gain available to reduce the distortion
  • reduced outout noues
  • lower offset at output

Nominal gain of an non-inverting amplifier is:

.. math::

text
G=Rf/Rg+1

Since we have a voltage divider with same resistors in the front of the amplifier the total gain becomes:

.. math::

text
G=Rf/Rg

The minimum gain specified in the TDA7293 datasheet is 26dB or 20 times. Just to be on the safe side we choose 10% bigger value: 22

Chosen values for E24 series:

  • Rf = 12kOhm
  • Rg = 510 Ohm

Chosen values for E48 series:

  • Rf = 11kOhm
  • Rg = 499 Ohm

Frequency compensation

The TDA7293 data-sheet does not provide enough of relevant data in order to model the IC in AC domain. Since we can't model it there are no optimizations available for the negative feedback circuit. But we can safely assume that there are high frequency poles present in the TDA7293 transfer function. For this reason we will add a few pF to calculated lead compensation capacitor below (see Cadd).

Lead compensation ^^^^^^^^^^^^^^^^^

Equivalent feedback network with lead compensation circuit::

text
      o Vout
      |
      *------+
      |      |
     +-+ Rf  |
     | |   ----- Cf=Cl (+Csi, see Input pin capacitance compensation)
     | |   -----
     +-+     |

Vf | | o-----*------+ | +-+ Rg | | | | +-+ | o Input

Resistors Rf and Rg are part of feedback network. Capacitor Cf is the compensation capacitor. The transfer function of this network is given as:

.. math::

text
Vf(s)=I(s)*Rg

Vout(s)=I(s)*(Rf||Cl + Rg)=I(s)*(Rf/(1+s*Rf*Cl)+Rg)

H(s)=Vf(s)/Vout(s)=(Rg/(Rf+Rg))*((1+s*Rf*Cl)/(1+s*Re*Cl))

Zero:

.. math::

text
wz=1/(Rf*Cl)

Pole:

.. math::

text
wp=1/(Re*Cl)

Where:

.. math::

text
Re=Rf||Rg=Rf*Rg/(Rf+Rg)

Rough estimation is to put additional 1-3pF in parallel to Rf.

.. math::

text
Cadd = 3pF

Input pin capacitance compensation

text
Input pins have the following parasitic capacitances associated:

* Cdiff
* Cm
* Cstray

The TDA7293 data-sheet does not specify any parameter regarding parasitic
input capacitances. Voltage feedback OPAMPS usually have both differential and
common-mode input impedances specified. In the absence of any information, it
is safe to use the model given in the next figure::

                   +----+ Zdiff
    +input o---+---|    |---+---o -input
               |   +----+   |
               |            |
              +-+ Zcm1     +-+ Zcm2
              | |          | |
              | |          | |
              +-+          +-+
               |            |
              ===          ===

We can use a rough estimation of values based on experience on using other 
audio FET OPAMPS, and typical values are around ``Cdiff=5pF``, ``Cm=4pF`` 

Parts

67
QtyValueFootprintReferences
6100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR6, R9, R10, R12, R14, R15
51N4148Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD3, D4, D5, D6, D7
522kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR16, R17, R18, R19, R20
5BC546BPackage_TO_SOT_THT:TO-92_Inline_WideQ1, Q2, Q3, Q4, Q5
4470nCapacitor_THT:C_Rect_L7.2mm_W8.5mm_P5.00mm_FKP2_FKP2_MKS2_MKP2C2, C3, C10, C11
4MountingHoleMountingHole:MountingHole_3.2mm_M3_ISO7380_PadMH1, MH2, MH3, MH4
310kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4, R5, R7
322nCapacitor_THT:C_Rect_L18.0mm_W7.0mm_P15.00mm_FKS3_FKP3C4, C5, C6
3BC556BPackage_TO_SOT_THT:TO-92_Inline_WideQ6, Q7, Q8
21Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R3
2100Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR11, R13
22u2Capacitor_THT:CP_Radial_D5.0mm_P2.50mmC12, C14
24k7Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_HorizontalR21, R22
26m8Capacitor_THT:CP_Radial_D26.0mm_P10.00mm_SnapInC8, C9
2GBU2508FDiode_THT:Diode_Bridge_Vishay_GBUD1, D2
110Resistor_THT:R_Axial_DIN0918_L18.0mm_D9.0mm_P22.86mm_HorizontalR1
1100nCapacitor_THT:C_Rect_L26.5mm_W10.5mm_P22.50mm_MKS4C1
110uCapacitor_THT:CP_Radial_D8.0mm_P2.50mmC15
1470nCapacitor_THT:C_Rect_L18.0mm_W11.0mm_P15.00mm_FKS3_FKP3C7
147kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR8
14u7Capacitor_THT:CP_Radial_D5.0mm_P2.50mmC13
1Kicad_LogoSymbol:KiCad-Logo_5mm_CopperLOGO1
1Kicad_LogoSymbol:OSHW-Logo2_7.3x6mm_SilkScreenLOGO2
1ac_inputTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-3-5.08_1x03_P5.08mm_HorizontalJ3
1ctrl_1Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ8
1ctrl_2Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ9
1power_1Connector_Phoenix_MC:PhoenixContact_MCV_1,5_3-G-3.81_1x03_P3.81mm_VerticalJ5
1power_2Connector_Phoenix_MC:PhoenixContact_MCV_1,5_3-G-3.81_1x03_P3.81mm_VerticalJ6
1signalConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ7
1switchTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_HorizontalJ2
1tr_priTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-3-5.08_1x03_P5.08mm_HorizontalJ4
1tr_secTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-3-5.08_1x03_P5.08mm_HorizontalJ1

More from nradulovic/hw_parvus

1
  • 2 layers70 × 66 mmParvus amp, the printed circuit board in 3D

    Parvus amp

    nradulovic/hw_parvus

    TDA7293 based audio power amplifier

    50 parts3GPL-3.0

Similar boards

  • 2 layers130 × 75 mmQ17-SIGMA PSU, the printed circuit board in 3D

    Q17-SIGMA PSU

    stefaweb/audio-psu

    Some power supply PCBs I developed.

    84 parts10GPL-3.0
  • 2 layers92.5 × 45 mm24V psu, the printed circuit board in 3D

    24V psu

    SpinningVinyl/PreConsonantPSU

    24V PSU for the PreConsonant phono preamplifier

    27 parts2
  • 2 layers160 × 99.1 mmFM VCO, the printed circuit board in 3D

    FM VCO

    mimeiners/ans

    HSB B.Eng. ET M 6.10 ANS

    104 partsApache-2.0
  • 2 layers85 × 107 mmPoweramp, the printed circuit board in 3D

    Poweramp

    electrucio/ltspice_pcb_viewer

    Umbrella project for visualizing and cross-exploring electronics designs (LTspice / KiCad schematics and PCBs). The project is composed of independent modules under modules/ that will be integrated into a single…

    47 parts
  • 2 layers84 × 54 mmLPTastatur, the printed circuit board in 3D

    LPTastatur

    stonedDiscord/Automatenplatinen

    Reverse engineerte Hardware aus deutschen Spielautomaten.

    23 parts5BSD-2-Clause
  • 2 layers34.4 × 46.6 mmOdysseyDaughterCardHorizSyncGenerator, the printed circuit board in 3D

    OdysseyDaughterCardHorizSyncGenerator

    Vibrant-Media-Lab/OdysseyNowDaughterCards

    Replacement daughter card schematics and layouts for the Magnavox Odyssey BLAK version.

    17 parts3
  • 2 layers95.3 × 58.4 mmClassA2, the printed circuit board in 3D

    ClassA2

    smileym4n-collab/Kicadprojects

    72 parts
  • 2 layers138.1 × 114.3 mmSilakka54, the printed circuit board in 3D

    Silakka54

    Squalius-cephalus/silakka54

    54-key column staggered split keyboard

    67 parts638MIT

Questions

How big is the Parvus psu PCB?

It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Parvus psu use?

67 parts, built around the BC546B and BC556B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Parvus psu KiCad files?

From the nradulovic/hw_parvus repository on GitHub, at the commit this page was made from: the board is parvus_psu/parvus_psu.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Parvus psu design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).