Skip to the content
2 layers38.1 × 43.1 mmIn13-nixie device, the printed circuit board in 3D

In13-nixie device

nonik0/in13-nixie-device1

This Nixie project is a continutation of the same spirit of most of my earlier Nixie projects: take an existing Nixie device, house it in a clean, well-built metal case, and maybe do a few addtions or modifications…

Size
38.1 × 43.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
33
Nets
49
Pads
171
Tracks, vias
255, 37
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
10 Feb 2025
Updated
14 Apr 2026

Overview

In13-nixie device is an open-source printed circuit board by nonik0, from the nonik0/in13-nixie-device repository on GitHub. It is a 2-layer board of 38.1 × 43.1 mm with 33 parts on 49 nets, routed with 255 tracks and 37 vias.

It is built around the ESP32-C6-MINI-1U-H4, LM358 and AP2112K-3.3, with the MMBTA42 among its other parts. Its parts include 10 resistors, 5 capacitors, 5 connectors, 4 ICs and 2 switches. It belongs with the lEDs and displays boards and the ESP32 and RISC-V boards of this library.

Main components

4

README

README.md

IN13 Nixie Device

Overview

This Nixie project is a continutation of the same spirit of most of my earlier Nixie projects: take an existing Nixie device, house it in a clean, well-built metal case, and maybe do a few addtions or modifications along the way. For me, the magic of Nixie tubes lies in their soft, ghostly glow—subtle, warm, and inviting. A simple, high-quality enclosure helps keep the attention where it belongs: on the Nixie itself.

Over the years, I’ve owned a few different Nixie thermometers, but they all came in acrylic cases. Aside from being acrylic, they were also bulky compared to the slim IN-13 tube and also used LED edge-lit acrylic to indicate temperature ranges. I don’t hate edge-lit acrylic on principle, but pairing that aesthetic with the aesthetic of Nixie tubes feels like a cardinal sin to me. I know there’s a huge market for flashy Nixie clocks with rainbow LEDs and effects, and plenty of people enjoy that style, but it’s just not for me. In my house, there’s a Nixie device in every room—and not a single RGB LED in sight. That’s been a personal rule for a while now.

At some point while browsing other Nixie projects, my mental levee broke and I had to start this project. TODO prototype? I started by finding a case I liked and sized well with an IN-13 tube, and worked back from that. My challenge for this was creating relatively cramped single sided PCB custom made for the case I had chosen, and this project is the result! and I dove into building this. I started by picking out a metal case I liked that fit the IN-13 well, and worked backward from there. My main challenge for this project was designing a compact, single-sided PCB tailored specifically to the dimensions of the enclosure I had chosen, and what you see here is the result!

inspiration: https://yager.io/vumeter/vu.html https://www.tindie.com/products/eclipsevl/in-13-bargraph-nixie-tube-with-driver-and-dc-dc/

Hardware

The hardware is designed in KiCad 8.0, and all design files are included in the hardware/kicad8.0 directory.

The main hardware components are:

Firmware

TODO

Images

TODO

Parts

33
QtyValueFootprintReferences
510kResistor_SMD:R_0603_1608MetricR2, R3, R5, R6, R11
4TestPointTestPoint:TestPoint_Pad_1.0x1.0mmTP1, TP2, TP4, TP5
21uCapacitor_SMD:C_0603_1608MetricC3, C4
222uCapacitor_SMD:C_0805_2012MetricC9, C12
25.1KResistor_SMD:R_0603_1608MetricR12, R13
2PINHD_1x4_MaleIN13-Nixie-Device:Pads_1x4_2.54mmJ4, J5
2SW_PushIN13-Nixie-Device:Mitsumi_SOFSeries_SMD_ButtonSW1, SW2
1100nFCapacitor_SMD:C_0805_2012MetricC2
1220Resistor_SMD:R_0603_1608MetricR14
1220kResistor_SMD:R_1206_3216MetricR1
12kPCM_Potentiometer_SMD_AKL:Potentiometer_Bourns_TC33X_VerticalRV1
1330Resistor_SMD:R_0805_2012MetricR4
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U4
1AudioJack3IN13-Nixie-Device:Jack_3.5mm_CUI_SJ1-3523N_Horizontal_NoEdgeSilkscreenJ2
1ESP32-C6-MINI-1/UPCM_Espressif:ESP32-C6-MINI-1UU2
1HV ModuleIN13-Nixie-Device:AliExpress_HV_ModuleU11
1LEDLED_SMD:LED_0603_1608MetricD3
1LM358Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU1
1MMBTA42PCM_Package_TO_SOT_SMD_AKL:SOT-23Q1
1PINHD_1x3_FemaleConnector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_VerticalJ1
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01AJ3

Similar boards

  • 4 layers90 × 95 mmBldc48, the printed circuit board in 3D

    Bldc48

    kobertkirk/bldc

    A KiCad hardware design plus STM32 firmware for a hall-sensored e-bike or scooter hub motor:

    133 parts
  • 2 layers16.6 × 22.5 mmThermostat controller, the printed circuit board in 3D

    Thermostat controller

    wipmate/electronics

    A collection of small ESP32-powered PCBs for use in smart home appliances.

    16 parts
  • 2 layers61 × 61 mmCo2-sensor, the printed circuit board in 3D

    Co2-sensor

    blinry/co2-canary

    An open-hardware, ultra-low power CO2 sensor

    57 parts78
  • 2 layers55 × 35 mmPb esp32c6-cape, the printed circuit board in 3D

    Pb esp32c6-cape

    anujdeshpande/pocketbeagle-esp32c6

    PocketBeagle cape with ESP32-C6-MINI-1U (IPEX) — KiCad 10 design, works on PB1 and PB2.

    32 parts1CERN-OHL-P-2.0
  • 2 layers41.5 × 44.5 mmEssai opt, the printed circuit board in 3D

    Essai opt

    NABL-A/Projet-Kicad

    26 parts
  • 4 layers50 × 50 mmAether node, the printed circuit board in 3D

    Aether node

    Pot4too/aether-node

    57 parts
  • 4 layers49.3 × 45.4 mmKbxIrBlaster, the printed circuit board in 3D

    KbxIrBlaster

    kbx81/kbxIRBlaster

    ESP32-based IR MegaBlaster!

    88 parts58CC-BY-SA-4.0

Questions

How big is the In13-nixie device PCB?

It measures 38.1 × 43.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the In13-nixie device use?

33 parts, built around the ESP32-C6-MINI-1U-H4, LM358, AP2112K-3.3 and MMBTA42. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the In13-nixie device KiCad files?

From the nonik0/in13-nixie-device repository on GitHub, at the commit this page was made from: the board is hardware/kicad10.0/IN13-Nixie-Device.kicad_pcb and its schematic hardware/kicad10.0/IN13-Nixie-Device.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the In13-nixie device design in my own project?

Its repository states no licence, so its author keeps all rights: ask nonik0 before reusing the design.