Skip to the content
2 layers25.4 × 25.4 mmConst led, the printed circuit board in 3D

This is essentially a flashlight I designed because I wanted to use some free parts from TI. This uses the LM3410 driver to boost the voltage of the LiPo battery and drive the LEDs at a constant current.

Size
25.4 × 25.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
77
Nets
26
Pads
144
Tracks, vias
152, 24
Pours
6
Routed
Yes
KiCad
KiCad 4
Created
26 Feb 2018
Updated
4 May 2018

Overview

Const led is an open-source printed circuit board by njeff, from the njeff/portaled repository on GitHub. It is a 2-layer board of 25.4 × 25.4 mm with 77 parts on 26 nets, routed with 152 tracks and 24 vias.

It is built around the ATTINY85-20SU, LM3410XSD and MAX17043X+, with the MCP73831 among its other parts. Its parts include 9 resistors, 7 capacitors, 5 diodes, 4 ICs and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

4

README

README.md

PortaLED

This is essentially a flashlight I designed because I wanted to use some free parts from TI. This uses the LM3410 driver to boost the voltage of the LiPo battery and drive the LEDs at a constant current. I have it setup to drive two 3W LEDs in series at approximately 630 mA (at max brightness).

An ATTiny85 is used to control the whole system, and push button is used input.

This repository has the C firmware code and the KiCAD PCB design files. The PCB in the const-led folder has an additional battery gauge IC (MAX17043) for more accurate battery level tracking, and the one in const-led-ez doesn't. I only made the ez variant.

Features

  • 8 brightness levels (maybe adjusted to be a linear/exponential ramp)
  • Battery level blink out (blinks out the volts, then tenth of a volt)
  • Low voltage/battery level cutoff
  • USB LiPo charging circuit

Parts

77
QtyValueFootprintReferences
3RResistors_SMD:R_0603R7, R8, R9
210uCapacitors_SMD:C_1206C3, C4
24.7uCapacitors_SMD:C_0603C1, C2
2D_SchottkyDiodes_SMD:D_SMAD1, D3
2LEDLEDs:LED_0603D2, D5
2SW_SPSTPin_Headers:Pin_Header_Straight_1x02_Pitch1.00mmSW1, SW2
10.1uCapacitors_SMD:C_0805C7
10.3Resistors_SMD:R_0805R4
110kResistors_SMD:R_0603R3
110nCapacitors_SMD:C_0603C5
1150Resistors_SMD:R_0603R5
116upersonal_f:muRata_LL1
11kResistors_SMD:R_0603R6
11uCapacitors_SMD:C_0805C6
12kResistors_SMD:R_0603R2
1330Resistors_SMD:R_0603R1
1ATTINY85-20SUpersonal_f:SOIC-8_8x5.25x1.27mmU3
1Conn_01x02personal_f:JST-PH-2J2
1LEDPin_Headers:Pin_Header_Straight_1x02_Pitch2.54mmD4
1LM3410Housings_SSOP:MSOP-8-1EP_3x3mm_Pitch0.65mmU2
1MAX17043personal_f:TDFN-8_2x3x0.75mmU4
1MCP73831TO_SOT_Packages_SMD:SOT-23-5U1
1Micro_USB_Bpersonal_f:Micro_USB_B_NHJ1
1TESTMeasurement_Points:Measurement_Point_Round-SMD-Pad_SmallTP1

The 31 most common of 77 parts.

More from njeff/portaled

1
  • 2 layers76.2 × 30.5 mmConst led, the printed circuit board in 3D

    Const led

    njeff/portaled

    This is essentially a flashlight I designed because I wanted to use some free parts from TI. This uses the LM3410 driver to boost the voltage of the LiPo battery and drive the LEDs at a constant current.

    183 parts1

Similar boards

  • 2 layers40 × 100 mmRemote, the printed circuit board in 3D

    Remote

    lucanastasio/myHomeAutomation

    Home automation stuff

    57 parts1
  • 2 layers140 × 70 mmSmarthomeswitch, the printed circuit board in 3D

    Smarthomeswitch

    aalvarezlopez/smartswitch_hw

    Electronic switch schematics and pcb

    154 parts
  • 2 layersDriver, the printed circuit board in 3D

    Driver

    Caraffa-git/LM3410X-Laser-Driver

    Yet another CC laser diode driver based on LM3410X

    10 partsGPL-3.0
  • 2 layers95 × 185 mmCalculator, the printed circuit board in 3D

    Calculator

    AnhadSawhney/MechanicalKeyCalculator

    These are the CAD files for a calculator with mechanical keyswitches.

    151 parts1MIT
  • 2 layers35 × 38.4 mmHandgelenk, the printed circuit board in 3D

    Handgelenk

    Jeija/esp8266-smartwatch

    ESP8266 DIY WiFi Smartwatch with MPU-9250, RTC, OLED, FT232, ...

    61 parts233
  • 2 layers109 × 71 mmGamma split, the printed circuit board in 3D

    Gamma split

    ahtn/keyboard_pcb

    156 parts96
  • 2 layers35 × 47 mmXling, the printed circuit board in 3D

    Xling

    mcusim/Xling

    Xling, a pocket demon

    77 parts67

Questions

How big is the Const led PCB?

It measures 25.4 × 25.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Const led use?

77 parts, built around the ATTINY85-20SU, LM3410XSD, MAX17043X+ and MCP73831. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Const led KiCad files?

From the njeff/portaled repository on GitHub, at the commit this page was made from: the board is const-led/const-led.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Const led design in my own project?

Its repository states no licence, so its author keeps all rights: ask njeff before reusing the design.