

Picopoweredv3
A simple microcontroller built around the RP2040.
- Size
- 39.7 × 56.8 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 54
- Nets
- 63
- Pads
- 255
- Tracks, vias
- 554, 103
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 17 Jun 2025
- Updated
- 11 Sep 2025
Overview
Picopoweredv3 is an open-source printed circuit board by nimitvijayvargee, from the nimitvijayvargee/picopowered repository on GitHub. It is a 4-layer board of 39.7 × 56.8 mm with 54 parts on 63 nets, routed with 554 tracks and 103 vias.
It is built around the RP2040, W25Q128JVSIQ and AP2112K-3.3, with the ABM8-272-T3, BAT60A and WS2812B among its other parts. Its parts include 18 capacitors, 15 resistors, 5 diodes, 5 connectors and 4 switches. It belongs with the RP2040 boards of this library.
Main components
6RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystalsBAT60A
SOD-323Schottky DiodesSlkorWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.mdpicopowered
A simple microcontroller built around the RP2040.
Changelog (V3)
- Redesigned board layout
- Doubled headers
- Dip switches and SD card slot connected to GP13-15 and GP16-19+29 respectively
- Better power system and circuit design
Changelog (V2)
- Replaced 2020 Neopixel with more available 5050 footprint.
- Fixed seperation between 1v1 and 3v3 power planes.
- Better positioning and tracing of the components to improve overall signal integrity.
- Added a regular LED to keep it somewhat compatible with regular Pico SDK Code.
- Modified USB C port to be THT Mounted rather than completely SMD.
- Moved GPIO 29 from VSYS Sense to an exposed pad on the bottom side of the PCB.
Featureset
| Stat | Raspberry Pi Pico 1 | Picopowered V1-RP2040 |
|---|---|---|
| Flash | 2MB | 16MB |
| Reset Button | No | Yes |
| LED | Yes (1 Color) | Yes (RGB Neopixel) |
| User GPIO Button | No | Yes |
| USB Type | Micro-B | C |
Disadvantages
- Linear regulator requuires minimum of 3.3 Volts, unlike Pico's buck boost converter which can be powered by 1.8 Volts.
No ADC_VREF (connected to GND instead) because the power by linear regulator is filtered already.ADC VREF now works with picopowered V2 and V3- No Power Mode selection (stems from power supply used)
Most of the disadvantages occur only due to the Pico's superior power supply system, but the system on the PicoPowered board is more filtered and smooth.
BOM
| Part | Cost (USD) |
|---|---|
| PCB + Assembly | 120 |
| Solder Wire | 3 |
| Headers | 3 |
For parts specific BOM, check picopowered.csv in /Production/
Gallery
V3 (Latest)

V2

V1

Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0402_1005Metric | C3, C4, C8, C9, C10, C11, C12, C13, C14, C17, C18 |
| 5 | 10K | Resistor_SMD:R_0402_1005Metric | R2, R12, R13, R14, R15 |
| 2 | 10u | Capacitor_SMD:C_0402_1005Metric | C5, C6 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C15, C16 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 2 | 330 | Resistor_SMD:R_0402_1005Metric | R8, R9 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | Conn_02x11_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x11_P2.54mm_Vertical | J6, J7 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D3, D5 |
| 1 | 10 | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 1K | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 1N4148 | Diode_SMD:D_SOD-123 | D2 |
| 1 | 2.2u | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 200 | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | ABM8-272-T3 | kicad-lib:XTAL_ABM8-272-T3 | Y1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | BAT60A | Diode_SMD:D_SOD-323 | D4 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_B3U-1000P | S1 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | LOGO | lib:orph | G*** |
| 1 | LOGO | lib:orph_cu | G*** |
| 1 | Micro_SD_Card | lib:Micro_SD_READER | J5 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_B3U-1000P | S2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | SW_DIP_x03 | Button_Switch_THT:SW_DIP_SPSTx03_Slide_6.7x9.18mm_W7.62mm_P2.54mm_LowProfile | SW2 |
| 1 | Solder Jumper | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | USB_C_Plug_USB2.0 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | P1 |
| 1 | USER | Button_Switch_SMD:SW_SPST_B3U-1000P | S3 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U2 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
More from nimitvijayvargee/picopowered
2- 4 layers21.6 × 52.1 mm

- 4 layers21.8 × 52.3 mm

Similar boards
- 2 layers138.8 × 96.4 mm

- 4 layers60 × 56.1 mm

- 4 layers60 × 56.1 mm

AvionicsPower
esb8/AvionicsPower
PCB of a Power Management and supply board for an Avionics stack.
82 parts2 - 4 layers20.3 × 99.1 mm

Proton
ewyrick-mark-1/Chromatone
Chromatone is an embedded audio visualizer running on the Raspberry Pi RP2350. It samples audio through the ADC, performs a real-time FFT, detects musical notes, and drives an RGB LED output based on the results.
119 parts1 - 2 layers49.7 × 28.8 mm

Koyomi keyboard adapter
exentio/koyomi-keyboard-adapter
Adapter board for Vaio P keyboards
35 parts4CERN-OHL-S-2.0 - 4 layers41 × 41 mm

- 4 layers50.8 × 106.6 mm

- 6 layers40 × 40 mm

Integrated FOC Stepper Driver
chpaxson/Echo-Telepresence
UC Berkeley ME 135/235 Spring 2025 Term Project
77 parts2
Questions
How big is the Picopoweredv3 PCB?
It measures 39.7 × 56.8 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Picopoweredv3 use?
54 parts, built around the RP2040, W25Q128JVSIQ, AP2112K-3.3 and ABM8-272-T3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Picopoweredv3 KiCad files?
From the nimitvijayvargee/picopowered repository on GitHub, at the commit this page was made from: the board is v3/PCB/picopoweredv3.kicad_pcb and its schematic v1/PCB/picopowered.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Picopoweredv3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask nimitvijayvargee before reusing the design.