Skip to the content
4 layers55.9 × 22.9 mmRiotee Board, the printed circuit board in 3D

The Riotee board is a development board for battery-free wireless devices. The on-board wireless microcontroller runs off energy harvested from, for example, a solar panel and uses only tiny capacitors as energy…

Size
55.9 × 22.9 mm
Copper layers
4
Thickness
1.64 mm
Parts
83
Nets
109
Pads
324
Tracks, vias
586, 203
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
14 Jan 2023
Updated
15 Feb 2026

Overview

Riotee Board is an open-source printed circuit board by NessieCircuits, from the NessieCircuits/Riotee_Board repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 4-layer board of 55.9 × 22.9 mm with 83 parts on 109 nets, routed with 586 tracks and 203 vias.

It is built around the SC0914(13), W25Q16JVUXIQ and 74LVC2T45GT, with the TLV73333PDBV, TPS71721DCK and TS5A3166YZP among its other parts. Its parts include 32 resistors, 28 capacitors, 10 ICs, 4 connectors and 3 diodes. It belongs with the RP2040 boards of this library.

Main components

12

README

README.md

Riotee Board Hardware Design Files

Kibot ERC/DRC

The Riotee board is a development board for battery-free wireless devices. The on-board wireless microcontroller runs off energy harvested from, for example, a solar panel and uses only tiny capacitors as energy storage. For uploading new software, the board can be connected to a PC via USB. During sotware upload and debugging, the microcontroller is powered with a fixed supply voltage from USB. After programming, the board automatically switches over to untethered, battery-free operation.

Latest design files:

Specification

3D rendering

Essentially, the Riotee board combines a Riotee probe and a Riotee module on a single board. The board has two 0.1" pin sockets that expose all relevant signals from the battery-free device, including 10 GPIOs that can be flexibly used for I2C, SPI or for reading analog sensors. These headers are also used to connect riotee shields to build fully featured devices without having to design custom PCBs. The board comes with a push button, an LED and a connector for a solar panel.

Specification:

  • 56mm x 23mm board with two expansion headers for shields
  • Boost converter with software-defined maximum power point tracking and energy measurement
  • 66uF on-board capacitance
  • 2V regulated output voltage
  • 64 MHz ARM Cortex-M4 MCU with integrated 2.4GHz radio
  • 128kB non-volatile FRAM to retain appliccation state across power outages
  • Ultra-low power RTC with power management functionality
  • Capacitor voltage sensing and ultra low power comparator with software-controlled thresholds
  • USB-C connector
  • CMSIS-DAP compatible: Supports programming via pyOCD and OpenOCD
  • Makes UART output from battery-free device available via USB
  • Push button and User LED

Firmware

The board has a dedicated controller (Raspberry Pi RP2040) that manages the upload of new firmware and the communication with a PC. This controller is powered from USB whenever the board is connected to a PC. The software running on the controller is the same as on the Riotee probe and can be found in this repository. To upgrade the firmware on the controller, connect a wire from one of the ground pins to the test pad labelled 'USB_BOOT' on the bottom of the board, while plugging in the USB cable. A removable storage drive should appear on your PC. Drop a UF2 compatible binary into the drive.

Parts

83
QtyValueFootprintReferences
190.1uCapacitor_SMD:C_0402_1005MetricC3, C4, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C28 +3
1012RResistor_SMD:R_0402_1005MetricR9, R10, R15, R16, R17, R18, R21, R22, R24, R25
85.1kResistor_SMD:R_0402_1005MetricR8, R11, R12, R19, R23, R26, R27, R28
6120RResistor_SMD:R_0402_1005MetricR7, R13, R14, R20, R30, R31
64.7uCapacitor_SMD:C_0402_1005MetricC5, C7, C23, C24, C25, C27
474LVC2T45GTriotee:NXP_SOT833-1U3, U4, U5, U6
31kResistor_SMD:R_0402_1005MetricR1, R4, R5
212pCapacitor_SMD:C_0402_1005MetricC1, C2
21MResistor_SMD:R_0402_1005MetricR29, R32
227RResistor_SMD:R_0402_1005MetricR2, R3
2LEDLED_SMD:LED_0402_1005MetricD1, D3
112402012E212Ariotee:AMPH_12402012E212AJ1
1CNK_KMR2riotee:CNK_KMR2_SWSW1
1Conn_01x02riotee:JST_S2B-PH-SM4-TB(LF)(SN)J4
1Conn_01x10riotee:PinSocket_1x10_P2.54mm_VerticalJ3
1Conn_01x12riotee:PinSocket_1x12_P2.54mm_VerticalJ2
1Crystal_GND24riotee:RALTRON_RH100Y1
1DNPResistor_SMD:R_0402_1005MetricR6
1DNPCapacitor_SMD:C_0402_1005MetricC26
1D_SchottkyDiode_SMD:D_SOD-523D2
1RP2040riotee:RP_RP2040U1
1RioteeModuleriotee:NC_RioteeModuleU10
1SI2302CDSriotee:VSH_SOT-23-3Q1
1TLV73333PDBVriotee:TI_DBV0005AU7
1TPS71721DCKriotee:TI_DCK0005AU8
1TS5A3166YZPriotee:TI_YZP0005U9
1TestPointTestPoint:TestPoint_Pad_D1.0mmTP1
1W25Q16JVUXIQriotee:WB_UX8U2

The 81 most common of 83 parts.

Similar boards

  • 4 layers43.2 × 22.9 mmRiotee probe, the printed circuit board in 3D

    Riotee probe

    NessieCircuits/Riotee_ProbeHardware

    The Riotee probe lets you program a Riotee module that is soldered onto your PCB or plugged into a breadboard. It has a standard 10-pin 0.1" connector compatible with the popular Tag-Connect cables that allow in-circuit…

    74 parts7CERN-OHL-W-2.0
  • 2 layers51 × 21 mmMitayi Pico D1, the printed circuit board in 3D

    Mitayi Pico D1

    CIRCUITSTATE/Mitayi-Pico-D1

    Open-Source RP2040 Microcontroller Development Board

    75 parts36MIT
  • 8 layers78 × 55 mmJetson AI Cam CopperPilot, the printed circuit board in 3D

    Jetson AI Cam CopperPilot

    CopperPilot/Jetson-AI-Cam-CopperPilot

    A carrier for Jetson Nano, Xavier NX and TX2 NX with two IMX219 cameras on a 39 mm stereo baseline, dual 4K outputs and CAN.

    305 parts15
  • 2 layers16 × 43 mmNrf24 remote, the printed circuit board in 3D

    Nrf24 remote

    dragonlock2/kicadboards

    Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere

    72 parts14Apache-2.0
  • 4 layers299 × 127 mmLaunch, the printed circuit board in 3D

    Launch

    system76/launch

    System76 Launch Configurable Keyboard

    385 parts1.4kGPL-3.0
  • 4 layers96 × 28 mmThelio io, the printed circuit board in 3D

    Thelio io

    system76/thelio-io-hardware

    KiCad electrical design of Thelio Io board

    78 parts70GPL-3.0
  • 2 layers85.2 × 107.8 mmVCU Module, the printed circuit board in 3D

    VCU Module

    VikingMotorsports/2027-SAE-Electric-VCU

    temp VMS VCU repo

    66 parts3
  • 2 layers68.6 × 53.3 mmSassuino uno dip, the printed circuit board in 3D

    Sassuino uno dip

    jre/sassuino

    Arduino-like AVR development board

    34 parts

Questions

How big is the Riotee Board PCB?

It measures 55.9 × 22.9 mm and has 4 copper layers, 1.64 mm thick.

What parts does the Riotee Board use?

83 parts, built around the SC0914(13), W25Q16JVUXIQ, 74LVC2T45GT and TLV73333PDBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Riotee Board KiCad files?

From the NessieCircuits/Riotee_Board repository on GitHub, at the commit this page was made from: the board is kicad/riotee-board.kicad_pcb and its schematic kicad/controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Riotee Board design in my own project?

Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).