Skip to the content
2 layers233.4 × 92.9 mmTitan keyboard, the printed circuit board in 3D

A QMK-powered keyboard for gaming, especially fighting games

Size
233.4 × 92.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
42
Nets
40
Pads
225
Tracks, vias
338, 0
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
22 Feb 2023
Updated
15 Sep 2023

Overview

Titan keyboard is an open-source printed circuit board by nekoewen, from the nekoewen/titan-keyboard repository on GitHub, published under the MIT licence. It is a 2-layer board of 233.4 × 92.9 mm with 42 parts on 40 nets, routed with 338 tracks and 0 vias.

Its parts include 19 switches, 18 diodes, 3 connectors and 1 IC. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.

README

README.md

The Titan

The Titan is a QMK-powered keyboard for playing video games, particularly but not exclusively fighting games. The design mixes in bits of the Sega Saturn controller (hence I named it after one of Saturn’s moons) and Hitbox controllers.

A photo of a completed Titan, with DSA keycaps A diagram of the default Titan layout from KLE

Bill of Materials

  • Pro Micro (or a compatible microcontroller, such as an Elite-C, BIT-C, KB2040, etc.) with headers
  • 17x 1N4148 through-hole diodes
  • 17x key switches (MX or Choc)
  • 17x keycaps; 15 should be 1u, and two should be 1.5u
  • 9x M2 standoffs
  • 18x M2 screws
  • 4 or more adhesive rubber feet
  • 2-pin reset switch (optional; 3x6x2mm DIP-2P switch, the same kind used on the Corne keyboard)
  • EC11 encoder switch with knob (optional)
  • WS2182B LED strip and 3 wires (optional)

Tools

  • Soldering iron with solder
  • Wire clippers
  • Wire stripper (if including an LED strip)
  • Screwdriver
  • Diode bending tool (optional; I use this one)

Build Guide

  1. Begin with the diodes. Bend the leads, insert them through the holes (the cathode is marked with a black line and should go on the square pad, so that the line on the diode matches the one printed on the PCB). Solder each diode, then use clippers to remove the excess leads.
  2. Take your Pro Micro and flash the firmware (see below). I recommend doing this before soldering it just in case you got a bad board.
  3. Solder the Pro Micro and its header pins to the underside of the board, with the Pro Micro’s components facing the board. You may want to use your clippers to trim off the excess part of the headers. If you’re adding a reset switch, put it into the PCB and solder its pins.
  4. If you’re going to use an EC11 encoder, solder it in place now. If you wait until you've soldered the switches, the top plate will being in the way will make it incredibly difficult to get the EC11 in place.
  5. From here you should be able to test the keyboard’s functionality. If you plug it in, it should register as a Titan keyboard, and you can use tweezers or a similar metal object to make contact on the switch pads to create the equivalent of keystrokes. If any of the keys don’t work, check to make sure you have the diodes soldered and facing the right direction, and also that the Pro Micro’s pins are all soldered in.
  6. Use screws to attach the standoffs to the top plate. It's a bit easier to do this step now.
  7. Put the top plate in place, and start pushing switches in place, though the plate and into the PCB so that each switch’s two leads go through the corresponding holes in the PCB. I like to put switches in the corners, solder them in place, and then fill in the rest of the switches. Once you’ve soldered all of the switches, I recommend testing the keyboard again to be sure that you have in fact soldered all of them. Once that’s done you can go ahead and put on the keycaps.
  8. If you’re including an LED strip for pretty lights, use 3 wires to solder the pads on the PCB to the corresponding ones on the strip. Be sure the DIn lead is going to LED DAT on the board, as they won’t work if you attach it to DOut on the LED strip. If you plug it into your computer now, it should light up!
  9. Flip the keyboard over, put the bottom plate in place (the placement of the screws make it so you need to orient it correctly), and use more screws to secure it in place.
  10. Finally, put some adhesive rubber feet on the bottom. You’re done!

Firmware

You can find a .hex file of the default Titan firmware in this repository. If you don’t have any need to customize the layout, you can just download this and flash it to your Pro Micro.

  1. Install QMK Toolbox if you haven’t already.
  2. Open titan_default.hex.
  3. Click the “Auto-Flash” checkbox.
  4. Plug the Pro Micro into your computer.
  5. Bridge the GND and RST pins with a metal object (or if it’s already soldered in place, press the reset switch).
  6. QMK Toolbox should automatically flash the firmware for you!

If you want to customize the firmware:

  1. Copy the “titan” folder from the firmware folder here into the “keyboards” folder of your QMK installation. You can modify the files in this folder as desired.
  2. Open a terminal window (for your OS if you’re using macOS or Linux, or QMK MSYS if you’re using Windows).
  3. Navigate to the QMK folder (typically cd qmk_firmware).
  4. Type “make titan:default” (or replace “default” with the name of your new keymap) and it should compile.
  5. Type “make titan:default:flash" (or replace flash with “dfu”) to flash it.

If you're using a KB2040 or similar controller, you'll need to use QMK's Converters feature, so for example compiling and flashing for a KB2040 would go as follows:

qmk flash -c -kb titan -km default -e CONVERT_TO=kb2040

Parts

42
QtyValueFootprintReferences
18DDiode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D2, D3, D11, D16, D17, D20, D24, D25, D26, D29, D30, D32, D33, D34, D37 +2
1AFOOTPRINTS:CherryMX_Choc_1uSW27
1BFOOTPRINTS:CherryMX_Choc_1uSW31
1CFOOTPRINTS:CherryMX_Choc_1uSW35
1DWNFOOTPRINTS:CherryMX_Choc_1uSW8
1ENTFOOTPRINTS:CherryMX_Choc_1uSW21
1ESCFOOTPRINTS:CherryMX_Choc_1uSW17
1JUMPFOOTPRINTS:CherryMX_Choc_1uSW18
1L1FOOTPRINTS:CherryMX_Choc_1uSW25
1L2FOOTPRINTS:CherryMX_Choc_1uSW38
1LED DATTestPoint:TestPoint_THTPad_2.0x2.0mm_Drill1.0mmJ2
1LED GNDTestPoint:TestPoint_THTPad_2.0x2.0mm_Drill1.0mmJ3
1LED VCCTestPoint:TestPoint_THTPad_2.0x2.0mm_Drill1.0mmJ1
1LEFTFOOTPRINTS:CherryMX_Choc_1uSW2
1LOGOFOOTPRINTS:LOGO MG***
1ProMicroFOOTPRINTS:ProMicroU1
1R1FOOTPRINTS:CherryMX_Choc_1uSW33
1R2FOOTPRINTS:CherryMX_Choc_1uSW39
1RESETFOOTPRINTS:1825965-1SW1
1RIGHTFOOTPRINTS:CherryMX_Choc_1uSW12
1RotaryEncoder_SwitchRotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mmSW4
1UPFOOTPRINTS:CherryMX_Choc_1uSW3
1XFOOTPRINTS:CherryMX_Choc_1uSW26
1YFOOTPRINTS:CherryMX_Choc_1uSW30
1ZFOOTPRINTS:CherryMX_Choc_1uSW34

Similar boards

  • 2 layers30 × 50 mmModuleV400, the printed circuit board in 3D

    ModuleV400

    stuartpittaway/diyBMSv4

    Version 4 of the diyBMS

    42 parts1.1k
  • 2 layers139.7 × 64.8 mmSprig console, the printed circuit board in 3D

    Sprig console

    hackclub/sprig

    🍃 Learn to code by making games in a JavaScript web-based game editor.

    42 parts1.1kMIT
  • 2 layers90.5 × 50 mmMain control board, the printed circuit board in 3D

    Main control board

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    42 parts1.1k
  • 2 layers67.6 × 30.5 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    42 parts1kGPL-3.0
  • 2 layers190 × 80 mmPcb shield, the printed circuit board in 3D

    Pcb shield

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    42 parts915
  • 2 layers98 × 80 mmMai io, the printed circuit board in 3D

    Mai io

    whowechina/mai_pico

    Pico controller for Maimai

    42 parts475
  • 2 layers50.8 × 90.4 mmOBOGS PANEL, the printed circuit board in 3D

    OBOGS PANEL

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    42 parts431

Questions

How big is the Titan keyboard PCB?

It measures 233.4 × 92.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Titan keyboard use?

42 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Titan keyboard KiCad files?

From the nekoewen/titan-keyboard repository on GitHub, at the commit this page was made from: the board is pcb/Titan Keyboard.kicad_pcb and its schematic pcb/KEY MATRIX.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Titan keyboard design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).